Видео

Thanks & My pleasure bro

ok i will try

folding and lining can be control by foil adjustment tight and loose if your foil alignment one side tight and one side loose than lining will be appear on blister Please try thanks for watching

Kaise kiye the

Yes for powder flowbility

Iske liye long video dekho Powder ka flow check karne k liye

Thanks

Thanks

👍

Thank you

Haan mujhe pata h Lekin ye alag systems hai

Bhai aisa b hota h Ye old machine par PRC set karne ka tarika h Jis machine par PRC ya servo nahi h Ye video bas unke liye h But aap ne dekh liye uske liye aap ka dhanyabaad 🙏🙏🙏

Thanks 😊 dear

Thanks for watching

Thanks

Very nice

Thanks

your welcome 🙏🙏🙏🙏🙏

welcome🙏🙏

Thanks dear

Thanks a lot 😊

Yes in this video I have only explain the formula and limit of Uncertainty but in another video I have explain the Uncertainty so you can check the video as link mentioned below ruclips.net/video/ma8jVTzTSow/видео.htmlsi=-VZshK3y1U_WxQUM Thanks for watching 👍👍👍👍

Yes

Replace your Printing drum also replace the Roller Pad In strip you can change the stereo

Thank you bro 🙏🙏🙏🙏

Welcome and Keep watching

Most welcome👍👍👍👍👍

The blister cutter gear formula in a blister packing machine is essential for determining the gear ratio required for cutting blisters accurately. Here's a general formula: Blister Cutter Gear Formula: The formula for calculating the gear ratio R needed for the blister cutter in a blister Packing machine is: R=Np X Nm/Nc X Ns/Nf Where: R=Gear Ratio Np=Number of teeth on the pinion gear (drive gear on the motor shaft) Nm= Number of teeth on the driven gear (connected to the pinion) Nc= Number of teeth on the crankshaft gear (connected to the cutting mechanism) Ns = Number of strokes per minute (desired cutting speed) Nf= Frequency of the machine (cycles per minute) Explanation: Np x Nm is the gear ratio between the motor shaft and the driven gear. Nc is the gear ratio between the driven gear and the crankshaft gear. Ns is the desired cutting speed in strokes per minute. Nf is the frequency of the machine, which is cycles per minute. Let's say: Np=20 (teeth on the pinion gear) Nm=80(teeth on the driven gear) Nc=60 (teeth on the crankshaft gear) Ns=100 (desired cutting speed in strokes per minute) Nf= 120(frequency of the machine, cycles per minute) R=20x80/60 x 100/120 R=22.67 x 0.833 R=22.23 So, in this example, the gear ratio R needed for the blister cutter would be approximately 22.23. This formula helps ensure that the cutting mechanism moves at the desired speed and is synchronized with the machine's operation. Adjustments to these parameters can be made based on the specific requirements of the blister packing machine. I hope you are understand well......Thanks for watching

Definitely bro, keep watching and enjoy 😍😍😍😍😍

Ok

@@PHARMAACQUAINTANCE number send kro

Thanks 😊

Hii

Hello thanks for watching the video

hai lekin kaha k liye

Ek baar video dhiyan se dekho usme bataya hai

Please check the Long video for Artwork related complete guide Link is mentioned below: ruclips.net/video/af6Auv-Rkj0/видео.html Thanks for watching

ok sir

@@PHARMAACQUAINTANCE ruclips.net/video/hcCqKfpuNFU/видео.htmlsi=3ccMAUCq4i_wJa3M Sir my Blister capsule PRC machine

You're welcome 😊

ok Boss, Try karte hai

As per your SOP or protocol

Thank you so much for watching the video🙏🙏🙏🙏🙏🙏🙏🙏

So nice of you

ok I will try

As soon as possible

Welcome

Thanks

Jo reading's show hogi wahi to result hoga Peak dawane k baad reading stable ho jaati hai

Same procedure you can follow or in Blister machine Pin hole detection system can be installed.