Видео

Excellent video! Thanks for sharing!!

What year is that deck you got

Where can i purchase this? TIA

Thanks! Very informative

Great tutorial! Way better than any other on RUclips! Thanks for making my job so much easier

Thank you

I like it

I forgot to mention in the video, but once you put the controller cover back on, switch your F&R switch from Neutral to Reverse 5 times in a row and wait for it to beep 4 times. This tells the controller to reprogram for the wire you installed and will get you maximum speed.

That's actually the friction wheel the drive disk is behind it looks like a pancake what is on the crankshaft

Why does it look like you were putting black dirt over the top of nice gravel

I put the same lift kit on mine when you put your front tires on did they rub against the new mounts for the tie rods?

I hooked it up the way you said.i put the positive wire on positive terminal , the ground wire has a terminal on it don't no were to put it. Help

Interesting to watch this. Makes me happy I own a Yamaha with independent (shock absorbed) front suspension and rack and pinion steering. Just a much better system than the EZGO.

Thanks so much! This worked on my lx280.

Best lift vid I’ve seen. 😊

Hey, great videos, you do a fantastic job my friend. Keep up the great work.

Great video. I probably couldn’t do this myself. Your awesome. Only thing I noticed is that the turn signal is usually on the outside. So either you install your lights upside down or to the opposite side of the cart. Either way great install. Works flawlessly. 🫡

Where can I buy me one of these cabs I really need one

Hello I am having trouble setting up my coward and reverse switch do you have any pictures or videos helping me link up all my cables ?

Well done! I'm new to golf carts and wanted to commend you on an excellent how-to video. As well would like to ask about the cart in the video. Is that engine/drivetrain setup factory or something you installed? I'm currently working on installation of a gas engine setup, replacing the factory electric setup on a late 90's model EZGO and if you could do a walk through of yours, that'd be great. New subscriber, keep up the good work.

Awesome video!!! Thanks

Good 👍 video pal

Thanks for the video! With the help of my brother-in-law, this 67 year old man just installed a 6” lift just like the one you installed. Great tip about the leaf springs on the rear. Only took us 3.5 hours. Very good information!!

Nice video. How has deck worked out after regular mowing ? I am thinking of doing this and would like to know if there are any negatives? Thanks in advance.

What an excellent video. You go through every step. Well done.

Hello, I noticed that there's a lot of wiggle. I have a similar issue, is that normal? Or does the whole assembly probably need changing? My frame is from the early 80's.

thank you for a very good and concise video showing exactly how to remove and replace the carburetor! best video on this I have found 🎉

What is the spec on the stop plate for belt tension arm?

Great video.

Great video, mate. Really enjoying your content 👍🏻

Please use Jack stands.. Never rely on hydraulics.

very helpful - thank you

Good job! Very simple and the camera was always on the job, without music or excessive talking. I enjoyed it!!

Great job! Definitely feel prepared to go do my lift on my ezgo tomorrow

Thank you. Hard to find honest fixes! Feeling more prepared!

I work with computers and have little experience working on things like this. I was wondering if any type of grease should be going on to these bolts when reinstalling and also would it make sense to replace those small rubber bushings since you already have everything off?

Thanks for sharing this info Tim! I've never installed this type wheel weight and your explanation makes it look pretty simple.

Dude, you should press your burns in and not hammer them and you’re supposed to use at least at bare minimum a socket. That’s approximately the same size as the outer ring. I hope you didn’t damage your bearings.

Good job man👍 look here too interesting @K.A.V

Great video bro! Helped with my install 100% appreciate it!

Is there anyway you could post a video of your wiring form your forward and reverse switch? I'm having issues wiring mine. Mine is a 1986 marathon EZGO. I see you have a cable running from the front of the forward and reverse switch to the negative side? I also see a cable on top of the solenoid, what is that connected too?

Great instructional video and not a step missing. 👍👍

Awesome video…you go straight for the meat of the job. I feel confident doing my 2006 TXTE now. Thanks for the help! Looking forward to seeing the big tires on yours.

What year is this?

Does it matter where the idle is at for the start up

Excellent job and please post more projects that have your interest because many others share the same interest... You did more than lift your cart, you lifted the confidence for others to lift their cart too. That's a three point fact. Best of luck. Brian

Great video! I have a 4100 with 2,450 hrs. I have a couple of tractors and I will never get rid of this one. The turn radius is incredible. The hands free option going from 2x4 to 4x4 is something every tractor should have. Let me know if you ever want to sell the loader. I put a battery tender on my battery with a quick connect. I keep it on a trickle when its parked.

What year is this cart? Thanks!

Great video, thanks!

how can I get one for a 425?