- Видео 105
- Просмотров 89 720
Sachin Fulsundar
Индия
Добавлен 11 июн 2012
The Channel helps you understand on Plastic Injection Molding Simulation Technology. Look out for more workflow flow video which unable you on Simulation Technology. Don't forget to subscribe and comment on videos
Autodesk Moldflow Adviser Warpage Interpretation
Short Clip-on warpage interpretation for Moldflow Adviser
Просмотров: 80
Видео
Improve your productivity with Moldflow Short cut keys
Просмотров 7421 день назад
Use your keyboard short keys to recall the commands. Reduce your nos of clicks to perform commands
Assembly Analysis - What's New in Autodesk Moldflow 2024
Просмотров 3835 месяцев назад
Assembly Analysis workflow in Autodesk Moldflow 2024
Thank you to Audience - 100th Episode of Moldflow's Tips and Workflow
Просмотров 565 месяцев назад
Thank you to Audience - 100th Episode of Moldflow's Tips and Workflow
Corrected shrinkage 3D - STAMP (Shrinkage Tested Adjusted Mechanical Properties)
Просмотров 1875 месяцев назад
Clip shows the workflow for STAMP - Shrinkage Correction factor for 3D mesh. Part of the Moldflow 2024 Enhancements
How to Raise Support ticket - Autodesk Moldflow
Просмотров 585 месяцев назад
Clip shows a workflow / procedure to raise the support ticket to Autodesk support team
What's New in Moldflow 2024 - Hot Gate Tetrahedral elements
Просмотров 3926 месяцев назад
Discription : Now with Moldflow 2024 user can directly import the Hot runner feed system with parts. Assign the Hot gate attributes to Tetrahedral elements. This will help to significantly reduce the time needed to create a feed system.
Negative Sink Marks Predictions - What's New in Autodesk Moldflow 2024
Просмотров 2496 месяцев назад
Sink marks are indentations on the surface of a plastic part and are often found on the opposite side of ribs. When a narrow thickness is surrounded by a large thickness, you can have a negative sink mark (or effectively a bump.
Coupled Analyses of Fiber Orientation and Polymer Flow
Просмотров 3817 месяцев назад
In the Autodesk Moldflow Insight 2024 release, two new options are available in 3D analyses to consider the fiber orientation's impact on thermal conductivity and polymer rheology, respectively. With these options enabled, the fiber solution and flow solution are fully coupled in the Flow solver. This means that the fiber solution is not only calculated based on the flow solution but also subse...
Min Max Histogram Moldflow 2024 -EP1
Просмотров 5027 месяцев назад
What's new in Autodesk Moldflow 2024 - discuss about the interface enhancement with the introduction of Min & Max and Histogram. How it has eased the result interpretations.
Automation in Moldflow using API's and Scripts
Просмотров 62711 месяцев назад
Automate the repetitive tasks in Moldflow using API and Scripts. Applicable for Synergy and Insight Solver
Autodesk Moldflow Report Automation - Audi Report
Просмотров 449Год назад
Like to Introduce to Report Automation in Moldflow Synergy 2023.02 via script- Audi Report
Void Prediction in Autodesk Moldflow
Просмотров 548Год назад
Void Prediction for the thicker part has been Alway challenging. Clip shows the work on how to predict the void within the part using volumetric shrinkage.
Use of Relative RAM Speed In Moldflow Analysis
Просмотров 382Год назад
Mapping of Relative RAM speed from XY Plot to Injection Control in Autodesk Moldflow Insight
Node Layer Number Across the Thickness
Просмотров 226Год назад
How to find node layer number across the thickness in Moldflow Insight.
Fusion 360 Injection Molding - Report Generation
Просмотров 151Год назад
Fusion 360 Injection Molding - Report Generation
Access to Moldflow 2021.2 Via Moldflow Synergy 2023
Просмотров 638Год назад
Access to Moldflow 2021.2 Via Moldflow Synergy 2023
Face Split & Element Alignment - Moldflow Synergy
Просмотров 280Год назад
Face Split & Element Alignment - Moldflow Synergy
Design Advise Analysis Fusion 360 & Moldflow Adviser
Просмотров 391Год назад
Design Advise Analysis Fusion 360 & Moldflow Adviser
Design and Process Optimization in Autodesk Moldflow
Просмотров 370Год назад
Design and Process Optimization in Autodesk Moldflow
Autodesk Moldflow Weldline - Dual Domain and 3D mesh
Просмотров 859Год назад
Autodesk Moldflow Weldline - Dual Domain and 3D mesh
Autodesk Moldflow Conformal cooling Comparison between Dual Domain and 3D Tetrahedral mesh - EP2
Просмотров 387Год назад
Autodesk Moldflow Conformal cooling Comparison between Dual Domain and 3D Tetrahedral mesh - EP2
Autodesk Moldflow Conformal cooling Comparison between Dual Domain and 3D Tetrahedral Mesh- EP1
Просмотров 916Год назад
Autodesk Moldflow Conformal cooling Comparison between Dual Domain and 3D Tetrahedral Mesh- EP1
Autodesk Moldflow 2023 3D Grill Elements
Просмотров 621Год назад
Autodesk Moldflow 2023 3D Grill Elements
EP2 What's New In Autodesk MF2023 User Interface and Capability Enhancements
Просмотров 433Год назад
EP2 What's New In Autodesk MF2023 User Interface and Capability Enhancements
Fusion 360 SIM Extension - Injection Molding
Просмотров 248Год назад
Fusion 360 SIM Extension - Injection Molding
Autodesk Fusion 360 - Product Design Extension, Design Analysis
Просмотров 2482 года назад
Autodesk Fusion 360 - Product Design Extension, Design Analysis
把软件交给印度人搞,是没有前途的,印度啥都不行
In sheet3 for final ram speed calculations =((OrigArea-OrigProfTotArea)/ShotSize)+E10 Here OrigProfTotArea is always 0 Is there right ,or you missing something in calculations
I will try this and give you feed back.Looks like you have used the existing circuit and added baffle with in that. Mostly Baffle / bubbler will be on seperate circute , will create and try send another comment later ( IF Everything works as you taught)
Thanks for your comments and feedback. Please give an try and let me know if any challenges
hello Mr.Sachin the intermediate cooling results doesn't work ... i tried to increase it multiple times but it only shows the same number every time ....tried to set it to write at specified periods but failed also ... do you have any solution for that ?
Hello Mustafa, great to know that you are exploring transient cooling. In setting there is option to increase default iterations. Possible for you to raise the support ticket to Autodesk team. They will surely guide you on same. Thanks Sachin
@@sachinfulsundar5012 Thanks
Should it be the node insert mesh with the node part meshes connected together or not?
Sir I want to know flow length of any material
Hello Krishna- Usually most of the resin manufacturers have the flow length of the material part wall thickness plot. Whichever material supplier with whom you are working please reachout to them
Sir it is not mention in TDS
You need to get in touch with resin manufacturers, it’s won’t be mention in TDS. They do special test for it.
Thank you for this tutorial. I tried by myself and your video confirm the need to import the study into moldflow to have the results. I tried to copy the study from moldflow to a folder then calculate with command prompt and copy the results back into the moldflow folder BUT it chrashes moldflow. I m searching for a solution to copy the result into the original moldflow folder
Good teaching skill 👍🏼
Great improvements, very easy to see the detailed results in short time thanks Autodesk team, Could Histogram be used in Thickness analysis plot too?
Great suggestion!
hi sir please share Ur contact number ?
How about Moldflow 2024 ?
Hi sir. Im a mould design engineer. Having 3 year+ experience. I need to do moldflow course. Can you provide me a suitable person or online platform.
Thanks Sir
SHOW
Hi Mr. Sachin Fulsundar, Thank you for making this video! This is a great idea to get the void. 22% is lowest number which can predict void, it means when we use this number for evaluation that there is no the void, we can rest assured that there will not be any the void for real model. Do I understand correctly? (However, we use 64% for evaluation that is reasonable). Where do you base on to use 22% or 64%? Is it from experimental test or your experience? Thank you!
Thank you for posting; this was clear and informative.
most informative video nice sir i want to do certification course autodesk insight can u help me please?
Nice information sir, Our students struck in fluid flow simulation for conformal cooling channels. Will you please provide your contact number to get support from you.
Where I can find coolant outlet command in autodesk 2023
Thank you Sachin, this would save a lot of time, I Cant see the download link to the scripts...am i seeing at a wrong place??
Thanks for your feedback, here is the link for the scripts - myshare.autodesk.com/:f:/g/personal/sachin_fulsundar_autodesk_com/EvN5Dki2RvdIg26iCL3tPqcB0DMCFFoWV4C51CsBmBYR2w?e=mkmHux
Can you provide complete video direct import Moldbase from any cad software And how to import mesh file from hypermesh into moldflow please make on video
Hi Mr. Fulsundar, how can we examine velocity result in the best correct way ?
background music makes focusing on your words difficult. Can you not just use a Volumetric Shrinkage plot with "x"% to show the same thing?
Hi, yes that's correct. Vid plot is derived from Vol shrinkage plot. Just subtracting the initial shrinkage and then applying the factor of 0.22 or 0.64
Plz make a video on mesh repair
Hallo Mr. Fulsundar, I have been using Moldflow for my thermoset injection molding simulations. Besides, I also use CFD tool OpenFOAM (FVM based) for the mold filling simulations. Interestingly, I see large difference in the simulated results from Moldflow compared to the Openfoam for same boundary conditions and material data. The difference arises in the numerical computation of the velocity gradient/shear rate. I know, that both software use different numerical methods. However, I am interested to know the differences comprehensively. Is there a way that I could get access to the documentation of Moldflow, where they explicitly mention about the underlying solving methods?
Hello, I would recommend you refer to Autodesk Moldflow help in the solver section to get more details - help.autodesk.com/view/MFIA/2023/ENU/
Can you suggest how to fill real parameter injection machine to moldflow software as Ram Speed vs Ram Position?
Thanks for the suggestion, I will work on it. :)
Thank you for share this video
I have downloaded crack version of Autodesk Moldflow Insight 2023. So while doing analysis when I click on launch Simulation Compute Manager, It is showing me that 'I dont have valid licence to perform analysis'. So I found this video where I can turn of My enternet and do the analysis through this Command prompt. Will It work sir ? Or Is there any other method which I can use
hello sir i want to learn mould flow sir so pls revert me sir
Hello, appreciate your eagerness to learn Autodesk Moldflow. You can refer to Autodesk Moldflow help to get started - help.autodesk.com/view/MFIA/2023/ENU/. For training reach out to Autodesk Moldflow Authorized Partner in your region
i am wait
pleas make 1 video installion and how to open
sir pleas tell me how to install moldflow insight 2019 and open it i am your student
Good morning sir 🙏
Thanks, Prahalada for your motivation!!
wow, we can define runner, spure, cooling from 3d cad (Catia, NX...) in Moldflow without export center curve. is that from 2021 version, that right ?
How to define runner system from Cad software (Catia, NX) in Moldflow ?
Hello Brian, if needed you can directly import the feed system CAD in native file format and assign the attributes in Moldflow as feed system. However I would recommend to convert in to beam. I have created a separate video on curve extraction using Fusion 360 and transfer it to Moldflow. I hope this helps thanks
@@sachinfulsundar5012 Thanks for you guide It good for me
Systems, Software, Engineering, Validations; Please upgrade seriousness levels, by cancelling the obnoxious background music and using a 'voice' microphone would be a good start. Thanks for the efforts and content.
Thanks for your valuable feedback. I will work on the improvements.
Dear Sachin Fulsundar, Is there Autodesk Moldflow 2024 version this year ?
Hello, im working on a new composite that tends to warp during drying, and I'm trying to analyse this warpage across different sizes, what software would you suggest I use?
Hi sir can u share ur contact number ?
Interesting topic
Hi sir . u have any gudie for moldflow?
Hi Vicky, you refer to Ascented website for Moldflow’s official guide - www.ascented.com/courseware/product/autodesk-moldflow-insight-2021-fundamentals
P r o m o S M ❣️
Nice video
Sachin san- great informative video as always. For warp as you mentioned we have corner effect and for parts other than box shape do we have other effect to consider?
Good section 👏
Thanks for u r video sir.
Great help, thanks Sachin, Could you provide with Exportlines Script at 3:45.
Thanks Raghu, I am uploading the script for line export
Thank you so much for your video. I would like to ask you if it is possible to run the simulation with the windows command prompt not with the Autodesk Moldflow command shell?
Great 👍, thank you sir 🙏
Thanks for your Video sir and it is Good and Excellent. I have one doubt why Hot Runner are placed on core side and If cavity side is aesthetic we can use tunnel or submarine gate. If it has any reason.
Respected sir Can I have u r number because I have so many doubt .