- Видео 18
- Просмотров 133 843
Melbourne Power Equipment
Австралия
Добавлен 13 июл 2017
Melbourne Power Equipment - We are a Power Equipment Dealership & Small Engine Workshop with over 50 years in the Industry! Videos on Carby Service/Repairs, Engine Services, and loads more how-to videos on Honda, Kohler, Aussie Pumps & Vanguard products.
EG. Honda EU20 & EU22i Carby Service/Repair
Disclaimer:
- Please read this disclaimer carefully before watching any videos on our RUclips channel.
- All content and media on Melbourne Power Equipment's RUclips channel is created and published online for Educational and Informational purposes only.
- While the information on this channel has been verified to the best of our abilities, we cannot guarantee that there are no mistakes or errors.
- Should you decide to act on any information from this channel, you do so at your own risk.
EG. Honda EU20 & EU22i Carby Service/Repair
Disclaimer:
- Please read this disclaimer carefully before watching any videos on our RUclips channel.
- All content and media on Melbourne Power Equipment's RUclips channel is created and published online for Educational and Informational purposes only.
- While the information on this channel has been verified to the best of our abilities, we cannot guarantee that there are no mistakes or errors.
- Should you decide to act on any information from this channel, you do so at your own risk.
Honda GX35 Engine Service (UMK435 Trimmer Engine)
A step-by-step guide on how to service your Honda GX35 Engine. These engines are fitted to Honda UMK435 Trimmers, and many other pieces of equipment. Thanks for watching! Please hit that like & subscribe button to get all of our future videos.
Просмотров: 43
Видео
Honda EU20i & EU22i Carburetor Service
Просмотров 8343 месяца назад
A dirty or contaminated Carburetor could be the cause of many starting, running or performance issues. This video goes through step-by-step instructions on dismantling, cleaning & re-assembling your Honda EU20i or EU22i Carburetor. We hope it helps!!
Honda GX Series (GX160 - GX390) Recoil Starter Repair
Просмотров 4,7 тыс.6 месяцев назад
A step-by-step guide on repairs to your Honda Recoil Starter (Pull Starter). Including replacing a broken rope and replacing a broken recoil spring. This video shows a full rebuild on both GX160 & GX390 Engine Recoil Starters. Spare parts available at www.melbpower.com.au #hondapower #smallenginerepair #smallenginemechanic #hondaengine #gx160 #powerequipment
Honda GX160 5.5HP Engine Service
Просмотров 6 тыс.7 месяцев назад
A step - by - step guide on how to service your Honda GX160 Engine. We change the Engine Oil, Spark Plug & Air Filter. Performed by a Genuine Honda Dealership. Parts can be purchased from: www.melbpower.com.au
Yamaha EF2000iS 2kVA Inverter Generator
Просмотров 4,1 тыс.8 месяцев назад
Hey everyone! This video runs through the features and specifications of the Yamaha EF2000iS Super Quiet Inverter Generator! Keep an eye on our online store for updated specials!. www.melbpower.com.au
Gentech EP8000HSR-RCD Generator Set
Просмотров 13 тыс.9 месяцев назад
A run-through on the favourite Gentech EP8000HSR-RCD. This Generator is recoil start, has 2 x 15A RCD protected outlets & the wheel kit & lift bar kit fitted. For more info please e-mail us on info@melbpower.com.au or visit melbpower.com.au/
Easy to use Oil Removal Kit
Просмотров 2,7 тыс.Год назад
Make messy oil changes a thing of the past. Suitable for all Power Equipment including Mowers, Generators & Pressure Washers. This kit comes with everything you need, no extra tools are required. Order yours now at: melbpower.com.au/easy-oil-extraction-kit
Honda EU22i Inverter Generator On Sale Now
Просмотров 4,7 тыс.Год назад
Huge EU22i Sale, $1849 for the Generator or $1949 for the Generator with the Accessories Pack. Free Delivery Australia Wide. Be quick, offer ends mid-December or while stocks last. Get yours now at melbpower.com.au/
Honda EU22i Inverter Generator Initial Setup
Просмотров 7 тыс.Год назад
A demonstration on how to get your New Honda EU22i Inverter Generator up & running from the box. We run through filling it with oil, fuel and how to start the generator up. Honda EU22i Inverter Generators available here: melbpower.com.au/honda-eu22i-inverter-generator-2.2kva
Honda GX690 V-Twin Engine Service
Просмотров 23 тыс.Год назад
A step-By-Step guide on how to service a Honda GX690 V-Twin Engine. Same process for GX630 & GX660. Service Kits for the GX690 Available Here: melbpower.com.au/honda-gx630-gx660-gx690-service-kit
The New Honda EU32i Inverter Generator (Fuel Injected)
Просмотров 9 тыс.Год назад
A run down on the all-new Honda EU32i Inverter Generator. The first of its kind in the 3kva range, this Fuel Injected Generator has some fantastic features! For more information, or to purchase one of these Generators, click the below link: melbpower.com.au/products/generators/recreational-generatots/honda-eu32i-3.2kva-inverter-generator
Honda 4-Stroke Blower Service
Просмотров 7 тыс.Год назад
Step-By-Step guide on how to service your Honda HHB25U 4-Stroke Blower. Honda Service Kits to suit available here: melbpower.com.au/honda-hhb25-blower-service-kit
Honda GX160 Carburetor Service (Same for GX120, GX200, GX270, GX340 & GX390)
Просмотров 40 тыс.Год назад
Honda GX160 Carburetor Service (Same for GX120, GX200, GX270, GX340 & GX390)
Honda EU22i Inverter Generator Service
Просмотров 10 тыс.Год назад
Honda EU22i Inverter Generator Service
thank you
Your very welcome Charlie!
You saved my day! thanks.
I'm glad the video helped mate!!
best on ive watched so far
Thanks heaps I'm glad you enjoyed it!
What is the black engine oil cap used for?
Hi David, the GX160 comes with one black & one white oil cap. The white oil cap has the dipstick attached, the black oil cap has no dipstick & is just an oil cap. They can be swapped to suit access. Cheers - Dave
@@melbournepowerequipment3441 Thank you sir!! Super appreciate the response!!
You are very welcome!
Hi Great video I got one delivered last week and noticed there are an extra tube and a couple of plastic bits in the box which I can’t figure out wether these are spares or should they be installed somewhere on the exhaust. Thanks in advance. Nik
Hi Nik, Thanks heaps mate! If you would like to send me a photo of the extra parts to info@melbpower.com.au I can have a look at these for you and let you know what they are. Cheers again - Dave
Thank you!
You're welcome!
Hi, I have a Honda gx690 engine running my power generator. The last time started, it ran for about 3 minutes, then stopped. Upon checking I realized that the carb as well as the exhaust muffler are all filled with fuel. I have tried this on three occasions and same scenario. Please what might be wrong? Thanks
Hi Abraham, It sounds like you Carby is flooding, most likely due to contaminants between the needle & seat inside the Carby not allowing the fuel flow to stop. The Carby will need to be removed & cleaned thoroughly, along with a new fuel filter and a good look in the fuel tank to make sure it's not full of bits of dirt/debris. I would also check the engine oil, when I see this issue in the workshop it normally fills the engine sump with fuel as well which dilutes the engine oil. If this is the case the engine oil will need to be removed & refilled, with a new oil filter. Thanks mate, I hope this helps! - David
Thanks David, I’ll go at it immediately and revert. Bless you.
You are very welcome!
Thank you so much for very informative and direct video. I have just bought a new Honda blower today at Bunnings.
You are very welcome!
best video for the Honda GX160 carbie !
Thank you I'm glad you enjoyed it!!
Great video! Thankyou! I think i have broken recoil spring but am unsure if there is something else wrong aswell, i try to wind the black wheel anti-clockwise and it makes a clicking noise and doesnt ever reach the point of being fully wound
Hi mate, it does sound like the spring ends may be broken. Feel free to send me a couple of photos to info@melbpower.com.au & ill have a look at it for you! Cheers - David
Life of this engine?
Hi mate, the GX160 will usually last 2000 - 3000 hours. This all depends on servicing intervals, the conditions of where the engine is running, and quality of parts & oils (Genuine parts will get you the longest engine life!) I have had Honda GX series engines through our workshop with over 7000 hours on the clock! Thanks - Dave
Nice thanks mate
No problem 👍
Excellent video thanks
Thanks heaps Peter!
Thanks
You are very welcome!
Great video old sport!
Thanks heaps mate!
Thank you for being the only person to use a Honda gasket kit and show the tiny oring was the pilot jet replacement, I couldn't figure where the left over, for me, oring went, thank you. You Aussies Rock!!
Im glad you found the video worked well for you!!! Thank you for your kind words!
You are a great teacher, very clear. Perfecto 👍🏼
Thank you heaps 😀
Is it possible to remove the bowl arms attached to the carb without breaking it?
Hi mate, is it the arms holding the float in with the pin that you are referring to? If so these are next to impossible to remove without breaking (i have tried 😂), as they are a non-serviceable part of the carburettor and are press-fitted in with plastic locking tabs. Cheers - David
@melbournepowerequipment3441 I thought it was pressed in. I thought maybe someone has been able to. But like you say you'd basically end up breaking it. You can't even buy a replacement seat. I was wondering since I was trying to remove all the plastic parts so I can soak my gx 390 carb in pinesol. I heard that the pinesol would eat away at any plastic pieces. It goes to a hot water pressure washer.
You are spot on that part cannot be purchased. A good clean out with Brake Cleaner / Carby Cleaner should do the trick, it dilutes and removes bad fuel contaminants quite easily. If that doesn't work, we use an ultrasonic cleaner with a carburetor cleaner that's safe on plastics and aluminum, they are the best options I have found so far!
The best tutorial compared to others. This one is easy to understand and detailed nicely. Thanks!
Thanks heaps mate!
How many litters of fuel consumption per hour of this engine.
Hi, the Honda GX690 Engine consumes 6.7 Litres of fuel per hour at 3600 rpm. Thanks heaps - Melbourne Power Equipment
Hello where do you get your replacement/maintenance parts from?
Hi, we are an Authorised Honda Dealer, all of our Honda parts are Genuine and come directly to us from Honda. We are also Authorised Dealers for Kohler, Yamaha, Aussie Pumps, Briggs & Stratton & many more! Thanks, from the Melbourne Power Equipment Team.
@@melbournepowerequipment3441 do you have a website so I can view parts for this motor?
We sure do, it is www.melbpower.com.au. If you can't find what you are looking for, shoot me an e-mail at info@melbpower.com.au & i will help you out, Cheers!
@@melbournepowerequipment3441 oh I just realized your in Australia? Do you have eBay Listing that way purchase can be easier for both of us?
No, we don't sorry. We currently only sell through our website. Thanks heaps!
Really helpful - many thanks 👍😊
Hi, i'm glad you found it helpful, please let us know if there is any other how-to video's you would be interested in. Thanks heaps, the Melbourne Power Equipment Team.
Is it fuel injected? I used to own a big generator (about 5kVa) but sold it with the property. This was the first Honda Genny that was fuel injected.
Hi Martin, The Honda EU22i is not fuel injected. The only Honda Generators currently fuel injected are the EU32i, and the EU70is. Cheers heaps!
Good job mate lots of info
Glad you enjoyed, thanks mate!
Great video, nice and easy to follow. Thank you. I’m have been looking for someone in Melbourne who sells genuine Honda service parts
Thanks for your kind words, Steve!
I am just wondering no one ever replaces the needle seat in the carburetor. I have a GX140 on a tiller and the carb. is overflowing, when my nephew brought it to me you could smell gas in the crankcase oil, I cleaned the carb and put it back together and a little while later the carb is overflowing again. Will take it apart again today
Hi John, The Needle seat is not replaceable on these types of Carburetors. You can however replace the needle itself. Check the tip of the needle, they are made of a soft material so if the tip of the needle has gone hard (as they do over time) you will need to replace it. If you are still having issues with the Carburetor after this, please send me an e-mail with your phone number to info@melbpower.com.au and i will give you a call. Cheers - David
@@melbournepowerequipment3441 great info. I was wondering this exact thing.