Thank you for being the only person to use a Honda gasket kit and show the tiny oring was the pilot jet replacement, I couldn't figure where the left over, for me, oring went, thank you. You Aussies Rock!!
I am just wondering no one ever replaces the needle seat in the carburetor. I have a GX140 on a tiller and the carb. is overflowing, when my nephew brought it to me you could smell gas in the crankcase oil, I cleaned the carb and put it back together and a little while later the carb is overflowing again. Will take it apart again today
Hi John, The Needle seat is not replaceable on these types of Carburetors. You can however replace the needle itself. Check the tip of the needle, they are made of a soft material so if the tip of the needle has gone hard (as they do over time) you will need to replace it. If you are still having issues with the Carburetor after this, please send me an e-mail with your phone number to info@melbpower.com.au and i will give you a call. Cheers - David
Hi mate, is it the arms holding the float in with the pin that you are referring to? If so these are next to impossible to remove without breaking (i have tried 😂), as they are a non-serviceable part of the carburettor and are press-fitted in with plastic locking tabs. Cheers - David
@melbournepowerequipment3441 I thought it was pressed in. I thought maybe someone has been able to. But like you say you'd basically end up breaking it. You can't even buy a replacement seat. I was wondering since I was trying to remove all the plastic parts so I can soak my gx 390 carb in pinesol. I heard that the pinesol would eat away at any plastic pieces. It goes to a hot water pressure washer.
You are spot on that part cannot be purchased. A good clean out with Brake Cleaner / Carby Cleaner should do the trick, it dilutes and removes bad fuel contaminants quite easily. If that doesn't work, we use an ultrasonic cleaner with a carburetor cleaner that's safe on plastics and aluminum, they are the best options I have found so far!
best video for the Honda GX160 carbie !
Thank you I'm glad you enjoyed it!!
Thank you for being the only person to use a Honda gasket kit and show the tiny oring was the pilot jet replacement, I couldn't figure where the left over, for me, oring went, thank you. You Aussies Rock!!
Im glad you found the video worked well for you!!! Thank you for your kind words!
Thanks tough guy, great video!
Thanks heaps mate!
The best tutorial compared to others. This one is easy to understand and detailed nicely. Thanks!
Thanks heaps mate!
Great video, nice and easy to follow. Thank you. I’m have been looking for someone in Melbourne who sells genuine Honda service parts
Thanks for your kind words, Steve!
I am just wondering no one ever replaces the needle seat in the carburetor. I have a GX140 on a tiller and the carb. is overflowing, when my nephew brought it to me you could smell gas in the crankcase oil, I cleaned the carb and put it back together and a little while later the carb is overflowing again. Will take it apart again today
Hi John,
The Needle seat is not replaceable on these types of Carburetors. You can however replace the needle itself. Check the tip of the needle, they are made of a soft material so if the tip of the needle has gone hard (as they do over time) you will need to replace it. If you are still having issues with the Carburetor after this, please send me an e-mail with your phone number to info@melbpower.com.au and i will give you a call. Cheers - David
@@melbournepowerequipment3441 great info. I was wondering this exact thing.
You are a great teacher, very clear. Perfecto 👍🏼
Thank you heaps 😀
Is it possible to remove the bowl arms attached to the carb without breaking it?
Hi mate, is it the arms holding the float in with the pin that you are referring to? If so these are next to impossible to remove without breaking (i have tried 😂), as they are a non-serviceable part of the carburettor and are press-fitted in with plastic locking tabs. Cheers - David
@melbournepowerequipment3441 I thought it was pressed in. I thought maybe someone has been able to. But like you say you'd basically end up breaking it. You can't even buy a replacement seat. I was wondering since I was trying to remove all the plastic parts so I can soak my gx 390 carb in pinesol. I heard that the pinesol would eat away at any plastic pieces. It goes to a hot water pressure washer.
You are spot on that part cannot be purchased. A good clean out with Brake Cleaner / Carby Cleaner should do the trick, it dilutes and removes bad fuel contaminants quite easily. If that doesn't work, we use an ultrasonic cleaner with a carburetor cleaner that's safe on plastics and aluminum, they are the best options I have found so far!