@@seminayahampath7193 hello, try to remove bms and then reset push the switch to reset the bms. If still red check the output of the battery if 36volts or lower the voltage
Hello, thanks for your help, have you ever seen both blue and red LEDs on the BMS flashing simultaneously? I have tried balancing each cell individually as much as possible and still no output and both LEDs flashing, thanks again
@@Edwintongol80 Thanks for your reply, after pressing reset button for 10 seconds I get fast red blink then one slow red, plug the charger but then again both red and blue, tried also reset while pluged into the charger
I have an e45. Error code 21 saying bms not detected. Took apart and it's still blinking blue. Made very sure no wires are loose. Do you think the bms is bad?
Yes , but mostly 48 error comes from es4 with external battery, due to damage port and loose power, if your scooter es4 with external remove battery external and you can use it again your scooter or replace the bms external battery.
Hi Joe, thank you for your great and informative videos. Please advice what can be wrong with my Ninebot ES2. I buy new front wheel with motor because old motor shakes and vibrate (not turning smooth, like steps) but after I change wheel, it is same problem... I take it apart and all wires are great connected, battery is blinking blue, but is 40Volts on instrument, not 36V is it normal? Please your opinion before I order new controller Thank you very much for reply Mario
Sense you bought a new motor but still have problem the motor , when you ride your scooter still vibrate, check all wiring including controller wiring some wire broken , or when you turn on the light motor noisy and when turn off your head lights noisy gone that issue is motor controller. Good luck God blessed
@@Edwintongol80 Thank you very much for reply. There was a problem in the controller (when I connect the blue wire from the motor to the controller, the motor does not turn smoothly, all wires have congtact and I can't see any burned out electronic element), now I replaced it with a new one and everything works as it should. In fact, I bought a new motor that I didn't need, because the old one works perfectly. :) Thanks again, Best wishes from Netherlands
Hello, Can I ask for help? I have a Ninebot e25 with error 21. I checked the battery, all cells are good, the voltage at the connector is 38V, the LED on the BMS is flashing blue.
Good day, mostly the issue for error 21 is the bms, check the terminal Rx, and tx terminal , also check the 120 ohms resistor from the bms if is open or bad resistance. Hope I will help you
Hello, I just bought the E25E plus the original external battery for the e25e. Could you please tell me if I should charge it to 80% (or how many%?) Or fully charge it to 100% to extend battery life? there is no information anywhere whether the batteries in this scooter have BMS or PCM ... thank you very much for your answer Regards
It's not matter how many % percent you will charger the scooter, don't zero percent your battery because sometimes it's hard to recover the BMS due to zero percent, better charger is 50 % your battery life charger but let cool down 30min . Before charging so that not damaged your battery
Hi joe I was wondering if you could give me some help my bird es4 won’t turn on but before the controler would get hot and it slowly started to die out and it just stopped working one day I order a new control but I am not to sure if that’s the problem,thank you
Good day, before you connect the new controller besure to check the battery voltage if is good 36 to 40 volts that's fine but below 👇 36 volts battery issue, if battery good and controller new open your dashboard maybe water damaged or broken wire. Hope that I help you a simple problem . Thank you god bless
Hello joe my names Jean how are you I wanted to ask a quick random question my Segway Ninebot ES2 is having a battery error Communication problem what can the problem be
Good day sir , remove battery first and the BMS circuit from the battery, then unplug the bms check the voltage of the battery you will get 36volts if lower 36 volts battery issue , if good voltage put back bms and rest blue blinking means good red blinking bad bms try to watch my channel in bms issue, god bless ruclips.net/video/zxBIC0-Y9Bs/видео.html
Sir my scooter ninebot nde nagchacharges pero pg tinangal ko external battery at chinarge ko..ok nman pero sa internal battery ayaw magcharge..binuksan ko yung blink minsan red at blue ..bms na kya to sir .thanks
Try to observe the bms first, if the the blue blinking good and voltage 36 volts battery ok, that the time to focus on controller board the issue of your scooter is controller thank you god bless
@@huaweihonor7714 bms is the battery management system on the battery. I'm very sorry how much in your country here in Dubai in our shop 290 dirhams in us maybe 80$ expensive , send to may email the video then I send video how to check if the battery or controller is damaged dwn_tongol@yahoo.com
Check mo muna nag battery voltaged mo sir 36volts dapat nakuha mo, pero sa error 21 bms talaga pero may pang solution yan send ka sa email ko para send ko saiyo mas madaling solution ng error 21 dwn_tongol@yahoo.com para send ko mga picture
Hello, can you please help me? I have a Ninebot Es2 with Error 21. I has torn down the battery and checked each singe cell, there are all OK. Blue led is blinking and voltage is 38V both at the terminal pins and cells. What is the problem? How can i fix it? Thanks in advance!
@@Edwintongol80 I am trying to reply to you and to provide you with my Whatsapp number but it seems my replies are not shown. Did you receive them? Thanks!
Do you know what could be wrong with my battery? Its blinking blue. If i measure on battery i get 3,36volt. If i connect white cable to controller i get 15-20volt that goes down to 10volt and stays there. If i connect charger it goes to blinking red and the charger blink green and red. If i connect it goes back to blinking blue.
For Ninebot battery when you directly charging led light blinking red and green means battery is charging, try to remove bms and check the volt battery voltage if 36 volts is good.
@@Edwintongol80 hi. Im sitting here atm and just watched every cell is ok. Between 3.74 to 3.77volt so all cells looks ok. Im thinking of buying the ”top” bms that is swapable. But of there a way to check the bottom bms is ok? Fuses seems ok and i can measure B+ and B- on bottom BMS and i get 37volt
Hi, bms din po b sira pag biglang ngshutsown ung scooter, ngcheck ako ng voltage merun naman 39V tapos blinking blue naman din, peru hnd ng tuturn on at hnd ngchacharge, ung charger blinking green at red lang
Hello, I need your help, I have more than 30 batteries with the failure of the bms, could you tell me how I could import them to Peru and how much it would cost me, it would be very helpful thanks
Sir please help me🙁My scooter fully charged randomly stop in road and display wont turn on. I checked bms battery blinking blue everything good I bought new display not working when i connect Please help me I am a college student
@@selmaaydin8737 even though the bms is blinking blue is ok, check your battery output voltage 36 volts you need to your scooter less than 36 volts have issued your battery. And also check your controller have power on
Kutang ke sana sir tang kaku segway es2 ya ing kaku.. issue na linwal ya tang temperature icon na red keng gilid. Tapus error15 din ampong ne kabilis ma discharge potang gamitan ke.. ng masaleseng gawan kanita sir?salamat keng answer.
Itang temperatura ninwal sensor ya keng battery mu ita potang dimla neh milako yarin. Error 15 ing accelerator brake mu papalit ya, makananu mabilis mag discharge, meg upgrade kaba scooter mo.download me ing m365 tool lawen me Sanu ing Ali mag charge kareng battery mu.
joeTech DXB es2 yapu sir nandin kasi mag charge ku sana oneng megcharge neman mga pilan mung mins ikit ke ene mag charge ga keng milako ne laman battery sir.. itang error 15 asulusyun ke sir ..atsu ku abu dhabi ngeni ekit kemu video mu sir mantun ku kasing solusyun ng pweding gawan..
joeTech DXB kung mabilis yang ma discharge sir ali ba payayalili battery kanita sir?sasabyan da kaku deng pikutangan ku battery replacement kanu..ok yamu sir kung sali keng external battery kesa replacement keng internal?
Uwa sira neh kanyan ing battery mu better na palitan me ing internal kesa sali Kang external pag meluwang neh terminal naning external Ali mune agamit mag ka error 42 neh lagi. Masmasanting palitan me ing internal battery mu
joeTech DXB palage mu sir mag kanu gastus na nita sakali?bang balu ku nung e junk kune mu kesa migastus kung maragul.. nung dubai kumu sir apuntalan daka agad pagawa ke na pamong kasakit lulub dubai kung bat ka abu dhabi..
No sorry, try to open your scooter battery, check nyo po ang BMS if not blinking try to reset first the bms ,and check your battery voltage, lower than 35 mahina na battery nyo, pero madalas nasisira lang po BMS sa Ninebot good luck po God bless
@@Edwintongol80 odometer only 13kms po - napabayaan Hindi ginamit and more than 1 month didn't charge battery. Hub motor running but can't charge battery . Thanks po sa reply
Hello po , medyo malakilaki na magagastos mo Jan bro. Better na bumili ka nalang ng bago, error 18 sa mother board or motor wiring, error 19 mostly sa battery or bms na. At medyo matanda na es1 pa.
Hi po.. i need your help... my ninebot es1 suddenly turns off when im going down the slope very fast.. it suddenly shuts down.. when i tried to open it again it wouldnt turn on.. i need help po
Hello Lory, mostly ES1 for this unit 2017 mostly like this. Try to check your battery the voltage, and the BMS battery, check also in apps m365 tools for the date manufacturing battery
Dubai based ka pala bro... Question bro, ES2 bigla nalabas ung 🔧 wrench icon, then ayaw nya umandar nag o-auto brake sya pero meron sya power... Parang need to repair pero di ko alam anu need i repair... Ty
Good Jericho, sa ganitong issue, Minsan Hindi agad nalabas ang error ,try mo munang up date ang scooter mo, pag ganun parin paikot mo ang motor Kung mabigat Siya may Tama ang wiring motor or sa controller mo,
Double check first if controller issue, error 18 between motor wiring or controller check all wiring on the motor, laki ikot mo sa by your hand Kung Hindi mabigat ang motor. Sa shop may controller kami
Nahinang ko na yung nakaspot weld sir. Pag chineck ko voltage sa terminals ng walang bms ang reading is 41.3v pero pag nilagyan ko ng bms biglang nagdadrop sa 3.7v same result kahit ibalik ko yung orig bms. Pag inalis ko bms magdadrop sa zero volts tapos dahan dahan aakyat sa 41.3v ulit.
hi sir ask ko lang po if ano problem kapag ayaw magcharge ng es2 pero kapag tinanggal ko battery and chinarge ko po sya ng rekta sa charger nagchacharge naman po pero kapag nakasalpak na sa stem ayaw magcharge
If you have extra controller try to changed and test, sometimes in the controller problem if the battery you said is charging, also check the terminal charging port to the controller maybe not connected good luck god bless😉
@@lesterarbildo Si? Pero si la sacas de esa forma, los pines que hacen continuidad con las celdas se doblan, te lo digo por experiencia, llevo un año reparando seguido esos scooter y la verdad, son muy delicados en sus componentes, también he reparado todos los errores y modificar la tarjeta para que no vuelvan a aparecer. 😎👍
@@daviddelatorreperez4 talves me puedes hechar la mano con esas fallas por que las de error 18 ya se que se remplaza o puentea y dime en tu localidad venden bms?
sir yung sakin wala power ayaw mag on pero pag sinaksak ko ang charger may naririnig akong tunog na isang beep. ayaw mag power on po. ano po kaya sura nun?
Hello count mo ang beep sound Kung m365 ang scooter mo. Kung pro scooter makikita sa dashboard mo Anong error and lalabas then messaged ka ulit sabihin mo Anong sira ng scooter mo, god blessed
Mayroon kabang Ninebot Segway apps connect mo Doon tapos punta ka sa battery limit baka naka limit lang ang charging Gawin mo 100%.yung bms blue light mabilis yan pag baka connect ang controller tapos naka on pa normal lang ang bilis., Pag naka tangal ang battery at mabilis parin may problems ang bms mo
Hi joeTech, My ES2 has a problem on charging, minsan charging, minsan ayaw magcharge. ang bilis din nya magfull, Tapos pag open mo ulit unit. 1bar nalang. Pinacheck ko sa service center, bms problem daw. Steady blue lang ung ilaw. Is there any solution bukod sa palit ng BMS? Thank you.
Maaeing bms nga ang issue ng scooter mo, pero Kung mabubukasan mo ang battery internal mo brod. Sometimes loose terminal lang yan, then check you battery cell Kung balances pa. Good luck god bless
Hello brod. Tignan mo ang BMS ng battery mo Kung may ilaw pa pay blue ok pa bms pag red try mo reset mins lag ayaw na at red parin sira nag bms mo pero pag tangay mo ng battery mo check mo ang volts ng battery wag lang baba sa 36 volts god bless po
sir patulong naman po diko alam ano problem ng ninebot es2 ko ayaw po mag charge tapos naka green lang yun charger. Diko alam kung charger ba or scooter na ang sira please reply.
Tangalin mo ang battery mo sir, makikita mo bms pag walang blinking lights reset mo muna . Pag wala parin try no palitan ang bms mo pero pay natangal ang bms tapat may makuha Kang 36 volts sa battery page mababa masira ang battery mo sir. God bless good luck
@@blairjand anong volts nakuha mo sa battery with bms, pag 36 volts na , Yung terminal battery at mag connection ng controller terminal buka mo ng konti may whatapp ka messaged mo ako 0509626002
Hello sir may i know po email or messenger nyo pptulong po sana ksi red nmn ung charger means its charging po dba pro di po mkita s screen ung percentage even sa app slmat po!
Kung ng charged naman ang battery mo sa may display po ba ang dashboard nyo. Or Yung battery level lang ang Hindi nakikita kailangan pong activate mo ang display sa apps po. Send to me the picture dwn_tongol@yahoo.com
Hello , not Ninebot E25 blinking Siya ng blue pero not charging dapat mag red yan para ng charge Siya, may issue po kayo sa bms. Kasi ng on pa ang scooter mo at nagagamit mupa , means stock nalang ng battery yan pag na ubos na di muna magagamit, wag muna zero battery mo mahihirapan lalu ang bms mo. Jumper negative charging at output voltage ng bms. Pag ayaw na mag charge means bms na po. God bless
Hi Po Sir Joe.. im here in Dubai din po. 😊 pano po kaya iffix ung problem ng ES2 ko. hindi po cya ngON then kapag nakacharge at in-ON ngerror 21 naman. 😩Can you please help naman po.. 🙏🏻 Thank you so much in advance. More power po ☺️
Hi Po Sir Joe.. im here in Dubai din po. 😊 pano po kaya iffix ung problem ng ES2 ko. hindi po cya ngON then kapag nakacharge at in-ON ngerror 21 naman. 😩Can you please help naman po.. 🙏🏻 Thank you so much in advance. More power po ☺️
I saw the different video maker and good thing is he reply to each of comments sir God bless you keep it up
Thank you God bless
I have same but blinks red. What can i do to make it work
@@seminayahampath7193 hello, try to remove bms and then reset push the switch to reset the bms. If still red check the output of the battery if 36volts or lower the voltage
36 volts without bms, if your get this number your battery cell good need to changed your bms.
Hello, thanks for your help, have you ever seen both blue and red LEDs on the BMS flashing simultaneously? I have tried balancing each cell individually as much as possible and still no output and both LEDs flashing, thanks again
Yes, if you seen blue and red your BMS try to reset first. After reset direct charging your battery to the charger
@@Edwintongol80 Thanks for your reply, after pressing reset button for 10 seconds I get fast red blink then one slow red, plug the charger but then again both red and blue, tried also reset while pluged into the charger
Need to changed the BMS, but before you changed the BMS be sure the battery cell are balanced. If not BMS not properly work.
I have a similar scooter which doesn’t charge or turn on … is it the BMS ? Or how can i send it to you ?
Check you battery if the blue blinking if not battery issue , red also need changed the battery,
I have an e45. Error code 21 saying bms not detected. Took apart and it's still blinking blue. Made very sure no wires are loose. Do you think the bms is bad?
Is this what causes the 48 error?
Yes , but mostly 48 error comes from es4 with external battery, due to damage port and loose power, if your scooter es4 with external remove battery external and you can use it again your scooter or replace the bms external battery.
Disconnecte a wire in that stem to derestrict??
Hi Joe, thank you for your great and informative videos.
Please advice what can be wrong with my Ninebot ES2. I buy new front wheel with motor because old motor shakes and vibrate (not turning smooth, like steps) but after I change wheel, it is same problem...
I take it apart and all wires are great connected, battery is blinking blue, but is 40Volts on instrument, not 36V is it normal?
Please your opinion before I order new controller
Thank you very much for reply
Mario
Sense you bought a new motor but still have problem the motor , when you ride your scooter still vibrate, check all wiring including controller wiring some wire broken , or when you turn on the light motor noisy and when turn off your head lights noisy gone that issue is motor controller. Good luck God blessed
@@Edwintongol80 Thank you very much for reply.
There was a problem in the controller (when I connect the blue wire from the motor to the controller, the motor does not turn smoothly, all wires have congtact and I can't see any burned out electronic element), now I replaced it with a new one and everything works as it should.
In fact, I bought a new motor that I didn't need, because the old one works perfectly. :) Thanks again, Best wishes from Netherlands
@@mariobriski6122 🤜🤛🏼
Hi can i still ride the ninebot e25 bind to previous owner...pls reply
Yes you ride, but soon mauubos din ang charging mas mahihirapan lang battery mo
Change serial, register in your own account.
Hello, Can I ask for help? I have a Ninebot e25 with error 21. I checked the battery, all cells are good, the voltage at the connector is 38V, the LED on the BMS is flashing blue.
Good day, mostly the issue for error 21 is the bms, check the terminal Rx, and tx terminal , also check the 120 ohms resistor from the bms if is open or bad resistance. Hope I will help you
@@Edwintongol80Hi, nice of you to help. I have the same problem. Where is the 120 ohm resistor located on the board? :)
What if my battery has a solid blue light but won't take a charge? Battery only reports 1 bar on screen. Bad bms?
If you bms not blinking or steady blue light only change your bms
Hello,
I just bought the E25E plus the original external battery for the e25e.
Could you please tell me if I should charge it to 80% (or how many%?) Or fully charge it to 100% to extend battery life? there is no information anywhere whether the batteries in this scooter have BMS or PCM ...
thank you very much for your answer
Regards
It's not matter how many % percent you will charger the scooter, don't zero percent your battery because sometimes it's hard to recover the BMS due to zero percent, better charger is 50 % your battery life charger but let cool down 30min . Before charging so that not damaged your battery
@@Edwintongol80 thank you
Hi joe I was wondering if you could give me some help my bird es4 won’t turn on but before the controler would get hot and it slowly started to die out and it just stopped working one day I order a new control but I am not to sure if that’s the problem,thank you
Good day, before you connect the new controller besure to check the battery voltage if is good 36 to 40 volts that's fine but below 👇 36 volts battery issue, if battery good and controller new open your dashboard maybe water damaged or broken wire. Hope that I help you a simple problem . Thank you god bless
@@Edwintongol80 thank you very much
Got a scooter on bottom says E22E but on app E25D,this normal?,any tips how make go faster bc 12mph to slow, PLEASE, many many thanks
Hello in my
Es4
There is error18
What we will do next
18 - Motor sensors fault , check your motor and controller
Very Informative sir..
Hello, what does it mean when the LED is constant blue (not blinking) and when it is red blinking?
Good day, blue blinking the BMS and battery working properly good and red blinking means I thier BMS or battery not working good luck god bless
@@Edwintongol80 whats does it mean when the LED is NOT blinking, it is constant, solid blue
@@ivomalinov4058 same, led not blinking.. And can't charge. Any solution?
@Ivo Malinov did you ever figure this out mine is the same?
hi my battery flashes red and does not charge, do you think sira na battery?
Bạn có bán mạch BMS này ko . Tôi muốn mua 1 cái .
My es2 with ext battery and modified dashboard was going uphill then randomly braked hard and turned off, can’t turn it back on. Any thoughts?
Open your scooter mostly wiring burn between motor and controller due to much power when to much accelerate inclined position good luck god bless
Hi, sinibukan ko kalasin yung battery ko hindi ko matangal yung kalahati. Saan ba shop mo baka pwede ko dalhin yung unit ko.
Dubai scooter service
@@Edwintongol80 pwede ko ba dalhin battery sa shop mo. Saan ang shop mo puntahan kita.
Hello joe my names Jean how are you I wanted to ask a quick random question my Segway Ninebot ES2 is having a battery error Communication problem what can the problem be
Good day sir , remove battery first and the BMS circuit from the battery, then unplug the bms check the voltage of the battery you will get 36volts if lower 36 volts battery issue , if good voltage put back bms and rest blue blinking means good red blinking bad bms try to watch my channel in bms issue, god bless ruclips.net/video/zxBIC0-Y9Bs/видео.html
Sir my scooter ninebot nde nagchacharges pero pg tinangal ko external battery at chinarge ko..ok nman pero sa internal battery ayaw magcharge..binuksan ko yung blink minsan red at blue ..bms na kya to sir .thanks
@@juanitoescabarte5389 may problem ka sa external port battery mo losses na palitan mo ang external battery port mo good luck god bless
Hello do you know how to fix Error 45 for a Segway ES2 ?(it shots down and you should connect the charger in order to turn on again)
Try to observe the bms first, if the the blue blinking good and voltage 36 volts battery ok, that the time to focus on controller board the issue of your scooter is controller thank you god bless
@@Edwintongol80 thank you for your answer. How much approximately do you think would cost to repair it.? (USD$)
@@Edwintongol80 what is the Bms?
@@huaweihonor7714 bms is the battery management system on the battery. I'm very sorry how much in your country here in Dubai in our shop 290 dirhams in us maybe 80$ expensive , send to may email the video then I send video how to check if the battery or controller is damaged dwn_tongol@yahoo.com
sir bms din kaya problem pag error 21? nagpalit nako board controller ganun pa din.. check ko din battery ok naman. salamat sa reply sir.
also, no blue or red blinking sa battery :(
Check mo muna nag battery voltaged mo sir 36volts dapat nakuha mo, pero sa error 21 bms talaga pero may pang solution yan send ka sa email ko para send ko saiyo mas madaling solution ng error 21 dwn_tongol@yahoo.com para send ko mga picture
@@Edwintongol80 maraming salamat sir :-) email sent po
@@francismangahas9482hi did you get a solution? Do you still have the email? Having the same problem :)
@@francismangahas9482did you get a solution that worked?
Hello, can you please help me? I have a Ninebot Es2 with Error 21. I has torn down the battery and checked each singe cell, there are all OK. Blue led is blinking and voltage is 38V both at the terminal pins and cells. What is the problem? How can i fix it?
Thanks in advance!
Do you have a Whatsapp number I send to you how easy to repair error 21
@@Edwintongol80 I am trying to reply to you and to provide you with my Whatsapp number but it seems my replies are not shown. Did you receive them? Thanks!
@@luigiciorra1565hi, did you get a solution that worked?
Do you know what could be wrong with my battery? Its blinking blue. If i measure on battery i get 3,36volt. If i connect white cable to controller i get 15-20volt that goes down to 10volt and stays there. If i connect charger it goes to blinking red and the charger blink green and red. If i connect it goes back to blinking blue.
For Ninebot battery when you directly charging led light blinking red and green means battery is charging, try to remove bms and check the volt battery voltage if 36 volts is good.
@@Edwintongol80 hi. Im sitting here atm and just watched every cell is ok. Between 3.74 to 3.77volt so all cells looks ok. Im thinking of buying the ”top” bms that is swapable. But of there a way to check the bottom bms is ok? Fuses seems ok and i can measure B+ and B- on bottom BMS and i get 37volt
@@jimmiepetersson344 BMS is hard to check voltage, only you need have extra parts check if bms is damaged.
@@Edwintongol80 seems like a fuse is blown. I get signal through fuse N but not Z. Can i solder it?
@@jimmiepetersson344 yes you can chenged or jumper the fuse
Hi, bms din po b sira pag biglang ngshutsown ung scooter, ngcheck ako ng voltage merun naman 39V tapos blinking blue naman din, peru hnd ng tuturn on at hnd ngchacharge, ung charger blinking green at red lang
Hello, I need your help, I have more than 30 batteries with the failure of the bms, could you tell me how I could import them to Peru and how much it would cost me, it would be very helpful thanks
Check your local courier services on your country sir.
@@Edwintongol80 but what kind of companies would you tell me here in Peru lima there are dhl and ups
Sir please help me🙁My scooter fully charged randomly stop in road and display wont turn on. I checked bms battery blinking blue everything good I bought new display not working when i connect Please help me I am a college student
@@selmaaydin8737 even though the bms is blinking blue is ok, check your battery output voltage 36 volts you need to your scooter less than 36 volts have issued your battery. And also check your controller have power on
New subscriber here idol
Hi ser my binebenta kba bms pang ninebot es2
Sir saan Po shop mo
Dubai po ako
Malapit po Al saga metro
Messaged muna bago pumunta 0509626002
Kutang ke sana sir tang kaku segway es2 ya ing kaku.. issue na linwal ya tang temperature icon na red keng gilid. Tapus error15 din ampong ne kabilis ma discharge potang gamitan ke.. ng masaleseng gawan kanita sir?salamat keng answer.
Itang temperatura ninwal sensor ya keng battery mu ita potang dimla neh milako yarin. Error 15 ing accelerator brake mu papalit ya, makananu mabilis mag discharge, meg upgrade kaba scooter mo.download me ing m365 tool lawen me Sanu ing Ali mag charge kareng battery mu.
joeTech DXB es2 yapu sir nandin kasi mag charge ku sana oneng megcharge neman mga pilan mung mins ikit ke ene mag charge ga keng milako ne laman battery sir.. itang error 15 asulusyun ke sir ..atsu ku abu dhabi ngeni ekit kemu video mu sir mantun ku kasing solusyun ng pweding gawan..
joeTech DXB kung mabilis yang ma discharge sir ali ba payayalili battery kanita sir?sasabyan da kaku deng pikutangan ku battery replacement kanu..ok yamu sir kung sali keng external battery kesa replacement keng internal?
Uwa sira neh kanyan ing battery mu better na palitan me ing internal kesa sali Kang external pag meluwang neh terminal naning external Ali mune agamit mag ka error 42 neh lagi. Masmasanting palitan me ing internal battery mu
joeTech DXB palage mu sir mag kanu gastus na nita sakali?bang balu ku nung e junk kune mu kesa migastus kung maragul.. nung dubai kumu sir apuntalan daka agad pagawa ke na pamong kasakit lulub dubai kung bat ka abu dhabi..
Hello, wondering if anyone would know, getting 40v on battery terminal, 20v in BMS, changed BMS to a new one, still getting 20v on BMS, any ideas?
This is the battery unbalanced check your battery when you put bms
Hi Joe Meron Kaba escooter shop sa manila. Pagawa ko Sana my ES4 with error 21
No sorry, try to open your scooter battery, check nyo po ang BMS if not blinking try to reset first the bms ,and check your battery voltage, lower than 35 mahina na battery nyo, pero madalas nasisira lang po BMS sa Ninebot good luck po God bless
@@Edwintongol80 odometer only 13kms po - napabayaan Hindi ginamit and more than 1 month didn't charge battery. Hub motor running but can't charge battery . Thanks po sa reply
Good morning nak dwen very good job dw sbi ni sasabel
Thank you Lola Glo god bless po🛴😊
Hello bro saan ka located bro? Kasi may alarm 18 at 19 es1 ko
Hello po , medyo malakilaki na magagastos mo Jan bro. Better na bumili ka nalang ng bago, error 18 sa mother board or motor wiring, error 19 mostly sa battery or bms na. At medyo matanda na es1 pa.
Saan po shop nyo pa check ko sana ES4 ko na scooter nag showing 19 na error po
Al safa metro Dubai scooter service po
Hi po.. i need your help... my ninebot es1 suddenly turns off when im going down the slope very fast.. it suddenly shuts down.. when i tried to open it again it wouldnt turn on.. i need help po
Hello Lory, mostly ES1 for this unit 2017 mostly like this. Try to check your battery the voltage, and the BMS battery, check also in apps m365 tools for the date manufacturing battery
Sir saan Po Yung shop niyo dito sa Dubai? Mgpapaayos ako Ng scooter ko
Al safa metro Dubai scooter service
Dubai based ka pala bro...
Question bro, ES2 bigla nalabas ung 🔧 wrench icon, then ayaw nya umandar nag o-auto brake sya pero meron sya power...
Parang need to repair pero di ko alam anu need i repair... Ty
Good Jericho, sa ganitong issue, Minsan Hindi agad nalabas ang error ,try mo munang up date ang scooter mo, pag ganun parin paikot mo ang motor Kung mabigat Siya may Tama ang wiring motor or sa controller mo,
Sir Meron kba Benta speed controller kasi meron error 18 yung ES2 tapos Meron nasunog sa controller.
Double check first if controller issue, error 18 between motor wiring or controller check all wiring on the motor, laki ikot mo sa by your hand Kung Hindi mabigat ang motor. Sa shop may controller kami
@@Edwintongol80 salamat sir, bili nlng ako sir Kung Meron ka dyan. Sabhin MO paano ko ipdla byad sir.
@@richardmechanicvlogs8803 pwedi Kang tumawag sa shop dubai scooter service tignan mo sa site namin
@@Edwintongol80 sir medyo mabigat ikutin yung gulong,
@@richardmechanicvlogs8803 anong number mo sa whatapps send ko video paano mag check hall sensor
sir pag blinking red pa rin after palitan ng bms anong issue na po nito?
Check your battery voltage if 36 volts, if less than 30 volts thiers a issue your battery, and also check the terminal battery
Yung naka spot weld tignan mo baka may natangal
@@Edwintongol80 thanks sir check ko yan later!
Nahinang ko na yung nakaspot weld sir. Pag chineck ko voltage sa terminals ng walang bms ang reading is 41.3v pero pag nilagyan ko ng bms biglang nagdadrop sa 3.7v same result kahit ibalik ko yung orig bms. Pag inalis ko bms magdadrop sa zero volts tapos dahan dahan aakyat sa 41.3v ulit.
Ok lang Yan Basta blue blinking ang LED light mo👍
Hi Joe my ES4 shows error 21 and battery charging not working. The motor hub is running. Paano po ayusin error 21
Check nyo po ang terminal between battery and controller, at ang battery led light pav blue it's means ok pag red sira na bms nyo po
Boss possible ba palitan yung battery connector ng external battery ng hindi bubuksan yung battery? Nasunog kasi akin eh di na recognized.
Yes pwedi palitan ang external battery mag upload ako ng video para sa port external battery repair
hi sir ask ko lang po if ano problem kapag ayaw magcharge ng es2 pero kapag tinanggal ko battery and chinarge ko po sya ng rekta sa charger nagchacharge naman po pero kapag nakasalpak na sa stem ayaw magcharge
If you have extra controller try to changed and test, sometimes in the controller problem if the battery you said is charging, also check the terminal charging port to the controller maybe not connected good luck god bless😉
Bro saan makabili ninebot ES2 bms?
Sa online lang sir.
Eso no es reparar la bms, y en segunda, así no se desarma la batería, jalando la tapa de arriba.
Saludos desde la ciudad de México
Esa es otra forma de sacar la.tapa. De la bms bro la.otra es desarmado toda la bateria pero que desarmar todo si con sacar esa tapa sale la bms
@@lesterarbildo Si? Pero si la sacas de esa forma, los pines que hacen continuidad con las celdas se doblan, te lo digo por experiencia, llevo un año reparando seguido esos scooter y la verdad, son muy delicados en sus componentes, también he reparado todos los errores y modificar la tarjeta para que no vuelvan a aparecer.
😎👍
Yo aqui tengo un par de fallas que me.destrozam la mente erro 21 y el error 42
@@daviddelatorreperez4 talves me puedes hechar la mano con esas fallas por que las de error 18 ya se que se remplaza o puentea y dime en tu localidad venden bms?
@@lesterarbildo No, pero te puedo vender las bms, de dónde eres amigo?
Hello po ano po kaya sira nang sakin naka blue lang po ung ilaw nya tas nag biblink na ung empty pero nagagamit
Good day, na downgrade mo ba ang scooter, ganito ng yayari pag Mali ang downgrade mo ng scooter.
sir yung sakin wala power ayaw mag on pero pag sinaksak ko ang charger may naririnig akong tunog na isang beep. ayaw mag power on po. ano po kaya sura nun?
Hello count mo ang beep sound Kung m365 ang scooter mo. Kung pro scooter makikita sa dashboard mo Anong error and lalabas then messaged ka ulit sabihin mo Anong sira ng scooter mo, god blessed
Boss ptulong nmn nitong es2 ko. Bakit hanging 4%lng yong battery kapag chenacharge ko at mggreen light na yong charger light. At yong blue light nng bms bigla bumilis nng pagblink konti. Thanks Godbless
Mayroon kabang Ninebot Segway apps connect mo Doon tapos punta ka sa battery limit baka naka limit lang ang charging Gawin mo 100%.yung bms blue light mabilis yan pag baka connect ang controller tapos naka on pa normal lang ang bilis., Pag naka tangal ang battery at mabilis parin may problems ang bms mo
kuya san ka po nag order ng BMS
Sa china brod.
@@Edwintongol80 pwede po mahinge ng link.
@@Edwintongol80 anong shop kuya salamat po
Sa alibaba Lang
Saan po nakakabili ng bms nito sir...
Sa online lang makakabili
Hi joeTech, My ES2 has a problem on charging, minsan charging, minsan ayaw magcharge. ang bilis din nya magfull, Tapos pag open mo ulit unit. 1bar nalang. Pinacheck ko sa service center, bms problem daw. Steady blue lang ung ilaw. Is there any solution bukod sa palit ng BMS? Thank you.
Maaeing bms nga ang issue ng scooter mo, pero Kung mabubukasan mo ang battery internal mo brod. Sometimes loose terminal lang yan, then check you battery cell Kung balances pa. Good luck god bless
Sir hndi nagchacharge po sakin ninebot es2 ndischarge lng ng sobra hindi n ngcharge at power
Hello , reset mo BMS, press mo Lang Ng 3 minute ang reset button, pag ayaw parin direct charging muna sa out put voltage gamit ang charger mo
Kapampangan ka pala idol
boss kapag ayaw magcharge pero my power pa sya 1 bar pa saan po kaya problema nun willing po ako pagawa sa inyo ng scooter ko ninebot es2 po.thanks
Hello brod. Tignan mo ang BMS ng battery mo Kung may ilaw pa pay blue ok pa bms pag red try mo reset mins lag ayaw na at red parin sira nag bms mo pero pag tangay mo ng battery mo check mo ang volts ng battery wag lang baba sa 36 volts god bless po
Hello Joe,good job(maganda) I need your contact so I can bring my es2 for bms replacement, thank you amigo.
You can go to our shop Dubai scooter service
Saan po sa Dubai shop nyo po
sir patulong naman po diko alam ano problem ng ninebot es2 ko ayaw po mag charge tapos naka green lang yun charger. Diko alam kung charger ba or scooter na ang sira please reply.
Tangalin mo ang battery mo sir, makikita mo bms pag walang blinking lights reset mo muna . Pag wala parin try no palitan ang bms mo pero pay natangal ang bms tapat may makuha Kang 36 volts sa battery page mababa masira ang battery mo sir. God bless good luck
@@Edwintongol80 Hi sir nagpalit nako ng bms ngayon Bigla lumabas na error 21 hays bago palit na po bms ko any help sir?
@@blairjand anong volts nakuha mo sa battery with bms, pag 36 volts na , Yung terminal battery at mag connection ng controller terminal buka mo ng konti may whatapp ka messaged mo ako 0509626002
@@Edwintongol80 Okay sir copy message kita sa watsapp
😂😢 16:27 😅 16:27 🎉 16:45
Hello sir may i know po email or messenger nyo pptulong po sana ksi red nmn ung charger means its charging po dba pro di po mkita s screen ung percentage even sa app slmat po!
Kung ng charged naman ang battery mo sa may display po ba ang dashboard nyo. Or Yung battery level lang ang Hindi nakikita kailangan pong activate mo ang display sa apps po. Send to me the picture dwn_tongol@yahoo.com
Hi po blinking lng po pero not nag chacharge...
Hello , not Ninebot E25 blinking Siya ng blue pero not charging dapat mag red yan para ng charge Siya, may issue po kayo sa bms. Kasi ng on pa ang scooter mo at nagagamit mupa , means stock nalang ng battery yan pag na ubos na di muna magagamit, wag muna zero battery mo mahihirapan lalu ang bms mo. Jumper negative charging at output voltage ng bms. Pag ayaw na mag charge means bms na po. God bless
Ok in dubai
Ask po ako contact smart or globe po
Boss saan ba mkabili ng bms ?
Try mo sa Ali express par, sa china kasi nang galing ang parts namin. Dito sa shop
good day baka alm nyu kung paano ifix ung error code 21 thank you.
Error 21 is the communication error with the bms check you battery voltage
@@Edwintongol80 palit po agad battery niya for error 21 since ayaw mag charge Yun battery ? The motor hub is running
Ay wow vloger na sya
Thank you Mr. Oscar Lab🛴
Pa shout out poo😍😍
Thank you Althea😊😊😊
@@Edwintongol80 ayyy na pansinn ni lodiiiiiiiiiii
E25 po
Hi Po Sir Joe.. im here in Dubai din po. 😊 pano po kaya iffix ung problem ng ES2 ko. hindi po cya ngON then kapag nakacharge at in-ON ngerror 21 naman. 😩Can you please help naman po.. 🙏🏻 Thank you so much in advance. More power po ☺️
Bms po and sira nyan, pero may why pa repair Basta ang battery good p Siya whatapp mo ako para video ko paano mo repair ang bms 0509626002
😢
no power es2 ninebot.
Check your battery 35 volts ang makukuha mong reading. If ok controller check and dashboard
Boss bka m2lungan mu ko nageerror 21 ung es2 ko bka m2lungan mu ko salamat
Try mo ayusin ang wiring between bms to controller , ng loose ang mga wiring terminal sa bms
your videos are great !!! but the Funky laugh is stupid !
😃😃😃👍
Hi Po Sir Joe.. im here in Dubai din po. 😊 pano po kaya iffix ung problem ng ES2 ko. hindi po cya ngON then kapag nakacharge at in-ON ngerror 21 naman. 😩Can you please help naman po.. 🙏🏻 Thank you so much in advance. More power po ☺️
Good day po, first check nyo po ang terminal controll to BMS battery pag ayaw parin bms na sira ng scooter mo. Good luck God bless
J'ai une erreur E1?plaes haow can i repair the problème, ninebote es2?