Thank you mister, for your job! By the way, why am I asked to Resynchronize the racking system each time I go in the DROP program? It says that the current part detect trigger value MAY NOT be valid.
I have another type of robot that I made for my graduation project.. Can I program it with this software ?? Is this software only used with fanuc robots??
That's A Great EffoYou🙏. I Want To Add An External Axis (Servo Motor)To Rotating My Welding Fixture.Is The Procedure Is Same As Above? Thanks In Advance
@@jithintsunny8939 Yes I want To Configure My Welding Fixture As An Additional Group. I Wasn't Perfect In Procedure And Which Motor I Have To Choose. Could You Please Share Me The Procedure How to Configure.. Thank You..🙏
Hi Jithin T Sunny, is it possible to share your roboguide program? If have same problems when I push cycle start. The conveyors run, but I didn't see the pallet anymore. Could you please tell me how to do it? If you want I can send my program to you.
Thank you, video is great, but I have an ask, when I run the drop program, an alarm error "TRAK 005: Track destination gone error", so how to fix this problem?
Thank you mister, for your job! By the way, why am I asked to Resynchronize the racking system each time I go in the DROP program? It says that the current part detect trigger value MAY NOT be valid.
congratulations my friend, very good
Hello, could you please demonstrate how to set up 2D vision and line tracking?
I have another type of robot that I made for my graduation project.. Can I program it with this software ??
Is this software only used with fanuc robots??
Hello, sir. Could you please create a video about 2D vision and IRpicktool?
I cannot get the "conveyor1:link1" to show up in simulation for the dropping part...
Select outfeed in conveyor type
@@jithintsunny8939 thanks man! Will see if that works tomorrow
Hello, could you please provide me with a program for setting up a 2D vision and line tracking system? Thank you.
Could you please share the workcell file? I am having some issues...
That's A Great EffoYou🙏.
I Want To Add An External Axis (Servo Motor)To Rotating My Welding Fixture.Is The Procedure Is Same As Above?
Thanks In Advance
Yes you can do so, But if you want to configure the Fixture as additional group the procedure is different.
@@jithintsunny8939 Yes I want To Configure My Welding Fixture As An Additional Group.
I Wasn't Perfect In Procedure And Which Motor I Have To Choose.
Could You Please Share Me The Procedure How to Configure..
Thank You..🙏
@@shaik-jp1vr see my new video
Hallo! Tell me, how are make irvision and line trekking both? Thanks!
Thank very much
It seems my DI[1] input does not active at the trigger point, did I miss something?
Good job.
I performed all the steps in the video, but this error appears when I try to run the programming "TRACK DESTINATION GONE ROBOGUIDE ERRO"
Hi Jithin T Sunny, is it possible to share your roboguide program? If have same problems when I push cycle start. The conveyors run, but I didn't see the pallet anymore. Could you please tell me how to do it? If you want I can send my program to you.
what is the values from your registers in robot controller 2?
those are the encoder values
Thank you so much Sir !
Thank you, video is great, but I have an ask, when I run the drop program, an alarm error "TRAK 005: Track destination gone error", so how to fix this problem?
I am getting this same error. Hopefully someone will tell us how to fix it.
Van Dong Nguyen, did you ever figure it out?
Remove the last line of home position in drop program. your program will run.
Info
Hi there, i need to use two links on the conveyor but it seems not to match their speed. Any ideas why this is happening?? Great video by the way!
they were synced in the end, simulation was faulty due to low end graphics card
Can you share the workcell file?
Are you teaching yourself or people who want to learn? This is not a tutorial, just bragging yourself
LOL TRUE
How do download soft ware
Thank very much