Почти пол миллиона просмотров. Как много любителей "простых" решений. Поднебесная без работы не останется. Nearly half a million views. How many lovers of "simple" solutions. Celestial without work will not remain.
Amigo bueno el circuito!!! Magnifico es lo que estaba buscando pero acomoda el diagrama que hiciste y el orden de los pones!!! Por que ese integrado tiene 25 patas no 23 y al indicar en el video el orden no está acorde con lo que estás haciendo en el video
Hola !! excelente el proyecto, pero tengo una inquietud ! Los numerosos de los pines creo que están mal, me confunden !! ?? Puedes explicarse mejor !! ?? Gracias bendiciones !!
Legal, mas não funciona, porque você precisa do pino 13 para alimentar a linha negativa do TDA. Já fiz esse teste e perdi tempo. Tenho outro projeto que funciona melhor que esse aí, e ainda por cima não precisa de muitas peças.
The real usable Output Power of this IC is 4 x 25W with 10%THD at 4Ohms Load. The IC is designed for 14.4 V. 18V is the absolute maximum rating. It's alwas better to use these ICs at their normal electrical characteristics. Please stop writing (wrong) Total Wattage of all four channels. You can't add the Power of all Channels together. Each Channel is separated and does it's own. And this IC is not a Hi-Fi Amp! The next thing you did wrong is to connect the left and right Channel of the Audio Cable together. In this way you can destroy the Output-Stage of the connected Audio Source Device. You have to decouple them with capacitors or even better with a little mixer-amplifier. Since the Left and Right channels are Stereo they often have different amplitudes - If one channel is positive and the other is negative in this moment it cause a short circuit - and this is what can be destructive. Pin1 is the connection for the TAB (the metal Part at the backside of this IC) and not a real GND. For the Audio Input Ground (Signal Ground) you have to connect Pin 13 (S-GND) that you have broken off... I don't know why and how it works, but you connected the positive Power Supply to Pin 22 (Mute) in your Video. To Power this IC in the right way, you have to connect way more Pins: Pin6 = VCC for Channel 1+2 Pin20 = VCC for Channel 3+4 Pin8 = P-GND for Channel1 Pin2 = P-GND for Channel2 Pin18 = P-GND for Channel3 Pin24 = P-GND for Channel4 Pin1 to Ground Pin13 to Ground Between Pin 10 and GND: Capacitor 47µF Between Pin 16 and GND: Capacitor 0.47µF Between Pin 4 and GND: Capacitor 1µF Between Pin 22 and GND: Capacitor 1µF For the TDA7388 Datasheet: www.mouser.de/datasheet/2/389/cd00179160-1796819.pdf
Hello, I appreciate your videos very much. But in the case of this, I have some doubts. I beg you to clarify them. According to the datasheet, the speaker outputs 3,7,19,23 are negative and 5,9,17,21 are positive. because it connects 3,9,17,21 as positive output and 5,7,19,23 as negative. Shouldn't all the positives be together as a positive exit and all the negatives as a negative exit ???? I beg you to clarify it for me Thank you very much in advance
@@JonePolvora I did, but the temperature rose quickly and as it was for domestic use, remove the jumper and only connect to the outer terminals (without bridging the internal ones) and the result is very good.
Hello congratulations on your videos I think I see that the resistance you put in series has the following colors white, brown, black and gold which gives me a value of 91 ohms is this true ??? thanks
Maximum 24 Watts output gets from a 6-ohm speaker by a 12V DC. Need a 0.9 ohm speaker or 7 numbers 6ohm speakers are in parallel to get 160w output from a 12v DC power supply... Very very bad idea...
Señor buenas tardes...solicito colaboracion en el ensamblaje de este circuito ya que al armarlo como aparece en la foto no suena como si no tuviera conectado los 12 voltios....
Ese amplificador no debería de producir audio porque en ningún momento veo que haya conectado el pin "mute" y el "stby" qué son necesarios para que habilite la amplificación 🤔🤔🤔🤔🤔 de hecho el mismo datasheet te manda a poner en esos pines, ciertos componentes para que funcione...
Bom... mas qualidade é que não há aqui rsrs , este CHIP entrega 10% de THD em 25W por canal 🤭 Só a 4W pra um THD menor que 1%. (fonte datasheet do componente)
Я сделал похожее но на tda7386 там схема получилась другая. Он показывает бред и так как он спал работать не будет. Но я спал по дугой схеме и все работает. Выдаёт явно больше 16 ватт. Не 200 конечно, но 100 будет точно. И из-зп того что соединены все каналы в один он неистово греется, даже с радиаторов 100+градусов. Так что буду пробовать не все каналы в один, а только 2.
по моему справочнику она выдает 21w на канал и того 84w ,эта мс не предназначена для паралельного подключения на сколько я знаю да и если она заработает она выдаст мощность только при нагрузке в 1 ом
but its just ~20w usage. show me you can press 160w from this ic, not for attacking but use, decaf/low-tones/constant low freq music to test, not place to disco XDDDDDDDD
I have a 7" android car stereo with the TDA7388 in it. ( It's a 2 din box that's mostly empty with a little tiny circuit board and this little chip). It has 4 X 45 watt RMS =180w but to get that , have to use 2ohm speakers. The thing is, that the amp has almost no distortion at full volume. As long as clear sound goes in, clear sound goes out. Driving My home speakers, is verrry loud and very clear. 15% volume vibrates the table ! 'This is my main TV Room amp Bluetooth sound system. works for me! Video out to TV. Other amp chips have way more distortion, and can only be run at 1/2 volume to get good sound. I can't turn this up and listen to it! too loud! But no hissing on the silent spots. That's driving $1000 8 ohm speakers of mine.
@@lightwave780 I´ve built me a bluetooth boombox with the TDA7560, which is a pincompatible version with MOSFET-powerstages. It does officially 4x80W @ 2ohms / 14.4V. Problem in a 2.1 boombox is, there´s only one center bass, so you can use only one channel´s power. In my box, as a compromise, there are two bass-chassis in tandem configuration, plus one passive membrane, each 4ohms and the amp is driven by 16V battery (18V is absolute max rating). This does vibrate the house - a little bit...
P = I 2 x R ..... , U 2 / R .....,,,,,...... if - R = 2 Ohm , 14,4 v / 2 = 7,2 A , ... , P = ( 7,2 A x 7,2 A ) x 2 Ohm = 51,84 x 2 = 103,68 W ,,, if - U = 12 V , P = 6 x 6 = 36 x 2 = 72 W 100 % True efficiency coefficient !
@@robertdiaz2604 Los altavoces del coche son de 2 o 4 ohmios, 8 ohmios no son preferibles en absoluto a un voltaje de suministro bajo de 12 - 14,4 voltios, a menos que el amplificador tenga una fuente de alimentación del inversor de + 40 / - 40 voltios en relación con la tierra / GND !
Maximum 24 Watts output gets from a 6-ohm speaker by a 12V DC. Need a 0.9 ohm speaker or 7 numbers 6ohm speakers are in parallel to get 160w output from a 12v DC power supply... Very very bad idea...
@@mohsenbabaeian2245 Amplifier product consists of several circuit. Like step-up voltage using fet to supply ic op-amp. High watt amplifier have many fet in parallel to share load high voltage. It's impossible for small size product to play in high current. Like 100A to get 1200W power. The pcb board will blown out.
Прикольно, новый класс усилителя, наверное ультра мега супер "D"!!! Потребляет 25, а выдает 160!
ФАНТАСТиК))))))
А что так можно было 😳
🧐😁
Hay ad chế mạch amply từ mấy con tda trong tivi đi chứ mấy con này ko thiết thực với những người ko đo ve chay nhìu:))
Почти пол миллиона просмотров. Как много любителей "простых" решений. Поднебесная без работы не останется.
Nearly half a million views. How many lovers of "simple" solutions. Celestial without work will not remain.
Amigo bueno el circuito!!! Magnifico es lo que estaba buscando pero acomoda el diagrama que hiciste y el orden de los pones!!! Por que ese integrado tiene 25 patas no 23 y al indicar en el video el orden no está acorde con lo que estás haciendo en el video
Así es, se equivocó con los pines 7 y 9, o yo estaré mal?
Los pines 24 y 25 no se utilizan, es para sensado y el otro no recuerdo pero no se suelen utilizar
20watts consumption.. About 5watt audio.... Excellent...
Bravo nene ai pus pinul 23 și pe plus și pe minus deci avem o ieșire spre difuzor in scurt! Felicitări
4 chanel ic amplifier. Good 👍, respect from Indonesian
Hola !! excelente el proyecto, pero tengo una inquietud ! Los numerosos de los pines creo que están mal, me confunden !! ?? Puedes explicarse mejor !! ?? Gracias bendiciones !!
Good tiching karte hai 👌👍👌👌👌👍👌
Cái này cụ nên làm 2 kênh L,R sẽ hữu ích hơn. Mong sớm có video
Your power supply states it is delivering 2A. Even if it runs at 100% efficiency (which it doesn’t) that would be 24watts, not 160
Legal, mas não funciona, porque você precisa do pino 13 para alimentar a linha negativa do TDA. Já fiz esse teste e perdi tempo. Tenho outro projeto que funciona melhor que esse aí, e ainda por cima não precisa de muitas peças.
Đơn giản quá mà cũng được phết nhỉ 😃😃
Nhưng em thấy bản mạch này rất hay nè
King of electrical💪💪😂😂
9:40 he started dancing himself 🤣🤣🤣
The real usable Output Power of this IC is 4 x 25W with 10%THD at 4Ohms Load. The IC is designed for 14.4 V. 18V is the absolute maximum rating. It's alwas better to use these ICs at their normal electrical characteristics.
Please stop writing (wrong) Total Wattage of all four channels. You can't add the Power of all Channels together. Each Channel is separated and does it's own. And this IC is not a Hi-Fi Amp!
The next thing you did wrong is to connect the left and right Channel of the Audio Cable together. In this way you can destroy the Output-Stage of the connected Audio Source Device. You have to decouple them with capacitors or even better with a little mixer-amplifier. Since the Left and Right channels are Stereo they often have different amplitudes - If one channel is positive and the other is negative in this moment it cause a short circuit - and this is what can be destructive.
Pin1 is the connection for the TAB (the metal Part at the backside of this IC) and not a real GND.
For the Audio Input Ground (Signal Ground) you have to connect Pin 13 (S-GND) that you have broken off...
I don't know why and how it works, but you connected the positive Power Supply to Pin 22 (Mute) in your Video.
To Power this IC in the right way, you have to connect way more Pins:
Pin6 = VCC for Channel 1+2
Pin20 = VCC for Channel 3+4
Pin8 = P-GND for Channel1
Pin2 = P-GND for Channel2
Pin18 = P-GND for Channel3
Pin24 = P-GND for Channel4
Pin1 to Ground
Pin13 to Ground
Between Pin 10 and GND: Capacitor 47µF
Between Pin 16 and GND: Capacitor 0.47µF
Between Pin 4 and GND: Capacitor 1µF
Between Pin 22 and GND: Capacitor 1µF
For the TDA7388 Datasheet:
www.mouser.de/datasheet/2/389/cd00179160-1796819.pdf
Perfect and best comment 👌
Thanks!
Es una gran ayuda técnica
Que proporciona información
De gran ayuda en internet.
Este vídeo es muy bueno ,pero debes hacerlo pensando q hay personas q no saben nada ,así tu canal nunca será grande ..
Anh hướng dẫn làm tda2030 làm thành mạch loa siêu trầm đi ạ
Bạn lên youtube hỏi cách làm mạch siêu trầm từ 4558 rồi ráp vào mạch của bạn là đc
Mua cái 300 ngìn có 2.1 nghe sướng lỗ tai. Ở điện tử Tuyên Quang bán đó
@@truongngochuyen2747 chế ra nó khác vs mua b
Nghe hay quá a ơi
Yo tengo una tda2089bj me serviría para emplearla en el mismo diagrama que acabas de explicar
Hello, I appreciate your videos very much.
But in the case of this, I have some doubts. I beg you to clarify them.
According to the datasheet, the speaker outputs 3,7,19,23 are negative and 5,9,17,21 are positive.
because it connects 3,9,17,21 as positive output and 5,7,19,23 as negative.
Shouldn't all the positives be together as a positive exit and all the negatives as a negative exit ???? I beg you to clarify it for me
Thank you very much in advance
I was wondering if he does the connection in "bridge" mode
@@JonePolvora
I did, but the temperature rose quickly and as it was for domestic use, remove the jumper and only connect to the outer terminals (without bridging the internal ones) and the result is very good.
RẤT BỔ ÍCH
Hello
congratulations on your videos
I think I see that the resistance you put in series has the following colors
white, brown, black and gold which gives me a value of 91 ohms
is this true ???
thanks
good bro
Thanks for knowledge
nice speaker dance
Maior lambança, esquema de um geito e montagem de outro geito, adivinha qual vai da certo.
Tại sao không lấy chân 13 làm mass của speaker input vậy bác ?
Very good 👍
No
Good work I try this
ủa, anh hàn sai chân mấy chân cuối rồi mà sao nó vẫn chạy vậy ?
Is it possible with Pioneer mosfet?
thích rồi đấy
Ic Toshiba TB2929 có làm được không a
exelente amigo.. saludos desde venezuela :)
All chanel in one ruclips.net/video/Qk8lEateE_M/видео.html
Saludos desde Brasil 🇧🇷
đậu xanh trước cứ tưởng nó chi cho ra 4 kênh được :D tìm mãi ko có chỗ nào gộp kênh :D
This is a great tutorial"leaving my footprint here and im waiting for your turn thanks
Chế thêm cái triết áp nữa thì miễn chê
How join the USB kit you're amp. Please next video
Làm về con tda9844j đi ad
Ad làm video hướng dẫn làm loa lắp D718 vs V5200 đi
Nếu so sánh cx thì D718 mà làm theo kiểu đẩy - kéo vs B688 thì mỗi cặp đc 100w
Còn 5200 vs 1943 đc 150-200w/ cặp
@@inhquangnguyentran1496 d718 và b688 1 cặp công suất tối đa chỉ 80w còn c5200 a1943 công suất tối đa 150w thôi nhé
@@Âm_Thanh_Nhi_Anh cái mình ns là cx tối đa có thể đạt đc bạn ak chứ ko phải là cx thực dụng
@@inhquangnguyentran1496 tối đa chỉ cặp d718 b688 chỉ 80w là hết cỡ còn thực dụng chỉ 50w
@@Âm_Thanh_Nhi_Anh mình xin tiếp nhận thông tin này còn cái ở trên mình cx chỉ nghe người khác ns thôi
160=16watt😂😂😂
True 12v 4 ohm
Hi res audio lol)
Anh có bán loa trầm 12v dành cho xe ÔT không
Блок питания показывает что максимум 20 ватт выдает, зачем врать?
Возможно громкость не накручена. В общем я сейчас попробую, если будет норм-отпишусь тебе)
Maximum 24 Watts output gets from a 6-ohm speaker by a 12V DC.
Need a 0.9 ohm speaker or 7 numbers 6ohm speakers are in parallel to get 160w output from a 12v DC power supply...
Very very bad idea...
Resistor colors are not clear. Do you write the colors in order?
Sipp...Mantul..tariikk sesss...
تستحق 1000000000000لايك،🌹🌹🌹🌹🌹🌹🌹🌹🌹🌹
Señor buenas tardes...solicito colaboracion en el ensamblaje de este circuito ya que al armarlo como aparece en la foto no suena como si no tuviera conectado los 12 voltios....
hola buenas ,yo llevo experimentando con este integrado unos dias
como l quieres usar 4 canales , 2 cacnales o mono?
Chào a
Chào bạn mình cũng rất thích đồ công nghệ.. Bạn chia sẻ mình mạch đó nhe.
13 Watt not 160 Watt
Anh chế amply với con CD5265CS đi anh chứ mấy con đò thì khó kiếm lắm
O falante fora da caixa claro que vai movimentar muito rsrs
Poisé kkkk
Ese amplificador no debería de producir audio porque en ningún momento veo que haya conectado el pin "mute" y el "stby" qué son necesarios para que habilite la amplificación 🤔🤔🤔🤔🤔 de hecho el mismo datasheet te manda a poner en esos pines, ciertos componentes para que funcione...
Ak ơi. Cho em hỏi, em ghép 3 quả pin 18650 thành 11v nhưng em ko có sạc 12v. Em có thể sạc từng quả mà có ảnh hưởng đến quả pin khác ko ạ.
Ad làm bộ âm ly hay bộ đẩy gì đó cho đôi bass 50w đi à
por que os canais do youtube utilizam auto falantes sem uma caixa acústica ???????????????? perdeu-se a noção da qualidade do som do amplificador
Bom... mas qualidade é que não há aqui rsrs , este CHIP entrega 10% de THD em 25W por canal 🤭 Só a 4W pra um THD menor que 1%. (fonte datasheet do componente)
@@LeonirZimmermann já serve pra por na caixinha de som q a vó escuta demanha na radio fm kkkkkkkkk
Wow excelente Amplificador Friends 😂😂👏👏👍🤞
Why the pinout of the transistor is up to 25 but why the last 23 should be 25 isn't it
thanks
Cool
ni se molesten es un fiasgo si comparan el datasheet del IC no coinciden los pines igualmente lo probe y no funciona solo perdi mi valioso tiempo
TIENES RAZON NO SIRVE NO FUNCIONA ES UN FIASCASO
Sent me your playlist
12V IN 4 OM=25watt 100%distortions square sine
All chanel in one ruclips.net/video/Qk8lEateE_M/видео.html
Hôm nay ad lại bị viêm họng nữa rồi không thích ad bị viêm họng như vậy =(
If you have 12V and not over 2A, and if it is right P=U x I so P=12x2. You have an amplifier with up to 24W (not 160W) sinus.
Ước gì em trai này ở Việt Nam
Mạch này sản xuất tại thái Bình nhé b
На таком радиаторе, не то что 160, даже 16 ватт раскачать проблематично.
Я сделал похожее но на tda7386 там схема получилась другая. Он показывает бред и так как он спал работать не будет. Но я спал по дугой схеме и все работает. Выдаёт явно больше 16 ватт. Не 200 конечно, но 100 будет точно. И из-зп того что соединены все каналы в один он неистово греется, даже с радиаторов 100+градусов. Так что буду пробовать не все каналы в один, а только 2.
E thấy cái máy kia báo công suất có 16w mà huynh
Me a gustado tu amplificador. Es muy sencillo de armar. Espero sigas enceñando.
Gracias. Marco acosta de maracaibo venezuela
Muy bueno, pero aslo de dos salidas
Top, muito bom.
Pois é, mas não funciona
@@eraudio que merda em kkk
23 pines???? Son 25 pines, es lo mismo que el TDA 7383
Voltage range: 12-24v? 4×100w power amplifier yd7388
Can i make with my pioneer Pal007c looks like the same pinout
Good
Buen video me gustaria que me facilite el grafico de un chip
по моему справочнику она выдает 21w на канал и того 84w ,эта мс не предназначена для паралельного подключения на сколько я знаю да и если она заработает она выдаст мощность только при нагрузке в 1 ом
по даташиту 41 ватт на канал!!!
@@PetrG-sg7ot только класс d на это способен но не АВ
😁😂😂😂 P=VxA 12v x 1A =12watt
tenes que ponerle una pasta térmica a ese integrado
y sera que puede con 8 parlantes
but its just ~20w usage. show me you can press 160w from this ic, not for attacking but use, decaf/low-tones/constant low freq music to test, not place to disco XDDDDDDDD
I have a 7" android car stereo with the TDA7388 in it. ( It's a 2 din box that's mostly empty with a little tiny circuit board and this little chip). It has 4 X 45 watt RMS =180w but to get that , have to use 2ohm speakers. The thing is, that the amp has almost no distortion at full volume. As long as clear sound goes in, clear sound goes out. Driving My home speakers, is verrry loud and very clear. 15% volume vibrates the table ! 'This is my main TV Room amp Bluetooth sound system. works for me! Video out to TV. Other amp chips have way more distortion, and can only be run at 1/2 volume to get good sound. I can't turn this up and listen to it! too loud! But no hissing on the silent spots. That's driving $1000 8 ohm speakers of mine.
@@lightwave780 I´ve built me a bluetooth boombox with the TDA7560, which is a pincompatible version with MOSFET-powerstages. It does officially 4x80W @ 2ohms / 14.4V. Problem in a 2.1 boombox is, there´s only one center bass, so you can use only one channel´s power. In my box, as a compromise, there are two bass-chassis in tandem configuration, plus one passive membrane, each 4ohms and the amp is driven by 16V battery (18V is absolute max rating). This does vibrate the house - a little bit...
Con TDA8511j chế mạch ampli được ko a
Допустим 160 китайских ватт. Но не по феншуй даже китайские ватты подавать на динамик без корпуса или аккустического оформления.
Hay
Nice
A hướng dẫn làm 2 kênh đi ạ
после первого просмотра чуть не поверил...уже полез за разобранным майфуном...посмотрел второй раз...ан нет...шляпа... ахаха
Buena idea para aprender
Pleas Reques pin STK4152 my from indonesia
P = I 2 x R ..... , U 2 / R .....,,,,,...... if - R = 2 Ohm , 14,4 v / 2 = 7,2 A , ... , P = ( 7,2 A x 7,2 A ) x 2 Ohm = 51,84 x 2 = 103,68 W ,,, if - U = 12 V , P = 6 x 6 = 36 x 2 = 72 W 100 % True efficiency coefficient !
Por 8ohm es la carga estás haciendo mal los cálculos
@@robertdiaz2604 Los altavoces del coche son de 2 o 4 ohmios, 8 ohmios no son preferibles en absoluto a un voltaje de suministro bajo de 12 - 14,4 voltios, a menos que el amplificador tenga una fuente de alimentación del inversor de + 40 / - 40 voltios en relación con la tierra / GND !
NOT POSSIBLE TO GET 160W WITH 12V YOU NEED AT LEAST 40V
Exactly. And its only drawing about 20 watts
and what about the car amplifire?thats 12 and we have 2000 watt amplifires,this means car amplifires are 20 watt?
Maximum 24 Watts output gets from a 6-ohm speaker by a 12V DC.
Need a 0.9 ohm speaker or 7 numbers 6ohm speakers are in parallel to get 160w output from a 12v DC power supply...
Very very bad idea...
@@mohsenbabaeian2245 The real car amplifer have a switching DC/DC converter for increase the voltage from 12 at min +40v -40v
@@mohsenbabaeian2245 Amplifier product consists of several circuit. Like step-up voltage using fet to supply ic op-amp. High watt amplifier have many fet in parallel to share load high voltage.
It's impossible for small size product to play in high current. Like 100A to get 1200W power. The pcb board will blown out.
con tda 7850 làm tương tự đc ko anh
6:28 на схеме тоже одни ошибки. не вводите зрителей в заблуждение
Оу, здарова. Проверял?
согласен с Вами
А что не так ? Вроде все норм
muito top!!!!!!
3-7-19-23 thì lại ghi 3-9-17-21?
Can i use this with 12 inch subwoofer??
Podes hacer con un tda 8920jb👍
TU ÉS O CARA MEU IRMÃO...