Fix Drill - PARKSIDE Performance "PSBSAP 20-Li A1" Gearbox Fail and Repair (Not Locking the Shaft)
HTML-код
- Опубликовано: 9 авг 2021
- #Parkside #Lidl #ErCanEverything
👉In this video I showed you, how to repair a noisy gearbox and non-locking drill shaft on Parkside Performance Cordless Drill
DIY 20 000 mAh QC3.0 Supported Parkside Power Bank from 20V 4Ah Parkside Battery! Just for $1👇
👉 • DIY 20 000 mAh QC3.0 S...
👇Thank you for Subscribing to my Channel👇
/ ercaneverything
Instagram👉 / ercaneverything
#DIY
#Homemade
#Inductioncooker
#Inverter
#HighFrequency
#HighVoltage
#HighCurrent
#HeatSink
#Computer
#Parkside
#Lidl
#PowerBank
#StepUp
#BoostConverter
#SilverCrest
#TableSaw
#Fence
#ElectricCircuit
#InductionHeater
#PCBbuild
#Soldering
#HowTo
#ToDo
#Craft
#HomeMaster
#HomeMade 
Хобби
Nice job!!!
Nice vide. I dont have this one yet. ✌️👍🤝
Sounds much smoother with more grease, they sound quite dry stock...
But how these little shafts came out at first place 🤔
Nice repair! They had to make you an official service 😁
😀😀😀🍻
Omg ⚙️🔧🛠
Nice and useful video :)
Thank You🤝
well done mate
Thank You
Good job
Thank You🙏🙏🙏🤝🤝🤝
Congratulations, another great video, thanks for sharing. I have a screwdriver just like this one that sometimes, without anyone touching it, starts working by itself. Do you have an idea as to what could cause this? a hug, thank you very much
Thank you very much🙏🙂🤝
This can be caused by moisture, a faulty button or controller?🤔
@@ErCanEverything thanks
😅😂😂😂😂🎉😢😢😢😢😮
anybody know a video that shows WHY a drill clutch keeps slipping? when in the drill mode
Good job.👍 It's waiting for me too. My drill has the same error, spins when loosening tools.
Thanks. I was a little worried about the disassembly, but it's not a difficult job. And easy to reassemble🙂
Ahoj vidim, že si rovnako uleteny pre značku parshite ako ja. I hold my thumbs up for your work. Looking forward for more vids from ya.
@@jozefhudak822 Vďaka kamarát, čoskoro nahrám nové video o nabíjačke do Parkside🙂
what are the function of the 6 tiny cylindrical parts? 3:35
I saw your video, I got the courage and decided to clean it, I have the same thing, I cleaned it, but the engine makes a ticking sound, it doesn't turn, what could be the reason?
Так-же была похожая проблема. Разобрал машину внутри все впорядке. Собрал, ничего не изменилось. Но потом обнаружил, что не до конца включался режим 1 скорости. Внутри заедает кольцо, на которое воздействует переключатель скоростей. Потом научился включать 1 скорость и проблема исчезла
Sometimes does not engage at 1 speed.
It needs a little load, and turns on immediately without a problem.
There was a small rectangular magnet that fell out of my drill when I opened it about 1cm wide 0.5cm high and 2mm thick.
Does anybody know where it might’ve come from?
And my magnet fell off while opening it, I thought a lot about where it could come from and finally figured out that its place is at the back down where the battery goes to hold the bits🤦🙂
What type of grease are applying?
Gear grease
Hello, how can replace the Chuck, thanks a lot
I haven't replaced but as far as I know you have to first unscrew the bolt inside the chuck with a screwdriver and then the chuck itself is unscrewed counter clockwise🙂
What made the gearbox fail?
I installed a large and heavy mixer tip and it causes such a problem during a sudden stop when spinning fast.
I might have same issue
Very easy to repair
@@ErCanEverything
lol.
I have never opened one.
But i've repaired a gasoline chainsaw ! :))
I might get to the end of this drill also.
✌️
Too much grease.
Terrible background music...
😁