Misquoted Taramps Bass 3K Fault Found 6 Hours Later (It Did Start Up!)
HTML-код
- Опубликовано: 10 дек 2024
- As requested, I will be providing links to tools, equipment, and supplies that I most commonly use. As an Amazon Associate, I earn from qualifying purchases. I do appreciate the channel support. Please review the privacy policies app.websitepol...
Secure your components from vibration damage - amzn.to/3z84kFb
Some of the better alligator clips I have found - amzn.to/3zd2gfl
The solder I use, good all-around size - amzn.to/3PekQcx
The Hakko desoldering gun I use - amzn.to/3z67ckX
Soldering Station - amzn.to/3AWgBxW
Don't let your roll, roll away with this solder stand - amzn.to/3IHX99O
Hakko desoldering gun filters - amzn.to/3z8NmXl
The scope - amzn.to/3AVJkmh
My newest meter with temperature reading - amzn.to/3PcPSBf
My original Uni-T meter for PC connectivity - amzn.to/3RETtKb
The LCR transistor tester - amzn.to/3OeAaUY
Amtek flux - amzn.to/3PdVCLh
If you are blind like me here is the headset I use - amzn.to/3IJY5KR
My go-to hot air station - amzn.to/3AR0ZvA
Contact cleaner I use for potentiometers and switches - amzn.to/3EuOJ5U
Here is the UV resin - amzn.to/3X7vhC0
This is the LED flashlight I use here - amzn.to/3CjWMjS
All points well communicated and demonstrate 👍
very interesting.
thank you!!
Just had a Sundown SFB-5k that kept heating up only one side of Mosfets. Transformer seemed fine but when using LCR meter, the inductance was way off compared to the other one. Replaced transformer and problem solved. The right meters are the key. Wouldn't have found this issue without that meter.
welcome back how was your vacation? lol
I know right. I told my wife I need to get a video out and what better headache to show than this oversight. I still take my Sundays off but it is getting hard as there are over 100 amplifiers in for service at this time.
@@ellensburgamplifier ok I understand take your time but we miss your vids
👍👍👍...
What do you charge per hour to fix amplifiers and how do i contact you
Thank you for the channel support. I do not charge by the hour but rather by the job. This is where proper quoting is essential, unlike what happened with this amplifier, as I missed the inductor during the quote to the customer. www.ellensburgamplifier.com/FAQS and all my contact info is on the site.
how you bypass the protection on those amps
Shoot me an email and I will give you the scoop on that. I don't want to be responsible for people blowing up their outputs from bypassing the protection circuits. This is a last resort in my books.
@@ellensburgamplifierok no problem it's jus for educational purposes only the more I know it's best for me
Is its transformer is not small for 3k watts sir?
What is the rail voltage in this amp sir?
How it gives the high wattage? With that small transformer and not so much copper?
What is the frequency in supply section sir?
The rail voltage is 98 volts. Your output is dependent on rail voltage. The components can be smaller due to the higher efficiency of the topology. The frequency of the supply is 20kHz.
@ellensburgamplifier +98 0 - 98 ? Or +49 0 -49?
20khz is too low for an efficient system. Higher the frequency, amp will become more efficient i think.
@@bamrahbabbu For design specifications and questions I would get in touch with their engineers.
Is it normal for taramps to get very hot very fast? Ive heard multiple people say taramps run hot and my md12000s get very hot
If you are wired low then they will heat up quickly. It all depends on how the amplifier is being driven. Make sure the fans are up to par!
@@ellensburgamplifier im wired to .5 ohm nominal and rising to 1 ohm. Also voltage dips down to 11v when the bass hits i do keep the signal clean by monitoring the clip light on the amp
@@TrendyBromando .5 at 11v will create significant heat.