Quality job! 👍 I'm just about to install some oak panels for a cinema wall, thanks for the tips. for the socket cut outs i'm using 25mm appleby extension boxes with the outside painted black and then refit the sockets flush. Or the plugs won't fit properly and will be fiddly squeezing the cable behind the slat. You just need to make sure the extensions are level with the slats so they don't pull them in when tightening the socket screws.
I feel like that whole bit about starting from the middle to ga s even gaps on each side is somewhat falls flat when you see the final result and there is a huge black gap on the left hand side
That's down to the left hand side wall isn't level, if you look closer to the bottom with cuts land with the same size gap, then we had to widen out cit toward the top to cater for the wall being out unfortunately! hopefully peoples walls on there home won't be put like one of ours. But well stopped
if you are cutting the felt you can do it with a trimming knife, if you need just another length of wood, you can pull them off with pliers because they have been stapled on, and if you need to modify the wood you can use a normal jigsaw. Cheers
@@MrandMrsDIY Hi, I believe that the cut of the panel should always be placed underneath so that it is not noticed, or is noticed less, as you put it at the top it is easier to notice, in my opinion.
Yes cuts best at the bottom as it can be hidden with silicon, however you may. not be able to afford to keep using new pieces and waisting the other half so you have to use both pieces @@giovannilabriola9821
These are not acoustic panels. I see them marketed on social media all the time as acoustic panels they are not. Most companies marketing these as acoustic panels show the acoustic tests with these placed against 4 inches of rockwool and the rockwool is whats doing the acoustic absorption not these panels. These panels are just purely decorative, and should only be used for decorative purposes
@@MrandMrsDIY these are acoustic panels in name only. It's what I had my little rant about. If you try looking up these panels, you will find there is no performance information at all. They provide no information on the frequencies they attenuate or the frequencies they damp. They are not acoustic panels and should not be used to tune a room they are purely decorative.
Thank you! Been watching quite some videos on this topic and yours is by far the best I’ve seen.
Thank you that's great to hear! Glad you like our video!
Cheers Craig, great explanation and easy to follow. Perfect
Many thanks glad it helped
or hope it helped
Brilliant...thanks for vid, planning on updating my pantry doors with this look.👍🇦🇺
Brilliant! Best of luck! We're pleased you found our video helpful!
Quality job! 👍
I'm just about to install some oak panels for a cinema wall, thanks for the tips.
for the socket cut outs i'm using 25mm appleby extension boxes with the outside painted black and then refit the sockets flush.
Or the plugs won't fit properly and will be fiddly squeezing the cable behind the slat.
You just need to make sure the extensions are level with the slats so they don't pull them in when tightening the socket screws.
Thank you mate, glad you found our video helpful!
Brilliant, exactly the guidance I need. Thank you! 😃
Many thanks Camper I hope our videos can help you, Nay question's just ask
Thak you so much for your " how to" video. It have been so helpful 👍
Thank you! No problem
Looking very nice 👍👍👍👍👍
Cheers
Many thanks
What is that uneven black gap on the left side of the wall @ 13:36?
Our plaster board had run out on one side and the panels are fitted perfectly lever so we took a slat off and cut the black felt to suit
@@MrandMrsDIY But its uneven and really contrasts with the white wall. I would rather leave a white plaster gap there - would be less noticeable
@@hagani18 Dealer's choice!
@@hagani18 That's right you could do
What's the best way to measure up around sockets it would have been nice to see how to measure around the sockets
Starts at 5:00!
Though it did,
With a tape.
I feel like that whole bit about starting from the middle to ga s even gaps on each side is somewhat falls flat when you see the final result and there is a huge black gap on the left hand side
That's down to the left hand side wall isn't level, if you look closer to the bottom with cuts land with the same size gap, then we had to widen out cit toward the top to cater for the wall being out unfortunately! hopefully peoples walls on there home won't be put like one of ours. But well stopped
What colour is that ? Just ordered samples x
R great this was the Jupiter
You have installed it on a brick wall or gyp board?
GYP board that has been skimmed with plaster and has a Brick wall behind it, cheers
How to cut extra length :?
if you are cutting the felt you can do it with a trimming knife, if you need just another length of wood, you can pull them off with pliers because they have been stapled on, and if you need to modify the wood you can use a normal jigsaw. Cheers
I would definitely fill it in at the bottom rather than the top, it will stand out less.
Yes that is an option depending on how you want the look and feel of your room to be, especially if you have furnishings that will go in front of it
Yep
Probably couldn't get em down in the summer of 76🥵🥵🥵
Hahaha, yes installing them was great!
Ha ha
il taglio del pannello va posizionato sempre sotto. va messo sempre sotto
apologies I can only Speak English I'm sorry.
@@MrandMrsDIY Hi, I believe that the cut of the panel should always be placed underneath so that it is not noticed, or is noticed less, as you put it at the top it is easier to notice, in my opinion.
Yes cuts best at the bottom as it can be hidden with silicon, however you may. not be able to afford to keep using new pieces and waisting the other half so you have to use both pieces @@giovannilabriola9821
Rubbish
Nice one
These are not acoustic panels. I see them marketed on social media all the time as acoustic panels they are not. Most companies marketing these as acoustic panels show the acoustic tests with these placed against 4 inches of rockwool and the rockwool is whats doing the acoustic absorption not these panels. These panels are just purely decorative, and should only be used for decorative purposes
Apart from not being acoustic panels are really good video on how to install these decorative panels. Thank you
Didn't mean to sound so negative
@@Keithmonnelly Thanks Keith, they describe them as acoustic panels on their website, cheers
@@MrandMrsDIY these are acoustic panels in name only. It's what I had my little rant about. If you try looking up these panels, you will find there is no performance information at all. They provide no information on the frequencies they attenuate or the frequencies they damp. They are not acoustic panels and should not be used to tune a room they are purely decorative.
Point taken @@Keithmonnelly
Glad you like the video of the install @@Keithmonnelly