I owned this from 1991 to 1994. It was impressive then. The sucessor TA-E2000ESD was better in all parameters, much better sound. One bit pulse converters in three chips, each one for front channels, surround channels and last to Center and subwoofer, however, the aesthetics of the former liked more. This last one owned from 1992 to 1995. I miss them.
Пожалуйста помогите!!!!! Как настроить уровень входного цифрового сигнала в Децибелах. Это под нижней крышкой слева Input level далее вниз Digital + - и плюсом минусом регулировать. Стояло на - 10 децибел. но звук тихий с приходиться ручкой прибавлять, тогда аппарат сильно греется. Меня это пугает. Сколько должно быть значение для его безопасной работы, что бы ему легко было. Спасибо. И У Вас он тоже сильно нагревается, особенно решетка сверху. СПАСИБО!!!!!!
Please, help!!!!! How to adjust the level of the digital input signal in decibels. This is below the bottom cover on the left of the Input level further down the Digital + - and the plus minus to adjust. Standing on - 10 decibels. but the sound is quiet with the use of a pen to add, then the unit is very hot. It scares me. How much should be the value for his safe work, what would it be easy for him. Thank you. And At you it too strongly heats up, especially a lattice from above. THANK YOU!!!!!!
Adjust the level to your liking ... If the input digital signal is clipping will appear a red light indicating it. ... Then you lower the input signal. This preamplifier warms up well, do not worry, just keep it in a well-ventilated place
It is not spectrum, what it shows is the parametric equalizer curve set .. This pre-amplifier has 3 digital parametric curves, where you can choose the center frequency and the slope (the slopes can be: two octaves, one octave, 1/3 and 1/12 per octave and gain of -12 to + 12 dB). That is, what the video shows are the factory presets, where the preset add the type of reverberation like hall, theater, etc (and its not visible sets of early reflections, reverberation, seat distance etc .), equalization and compression (or expansion) It is a very versatile preamplifier, considering it was released in 1991 !!
I owned this from 1991 to 1994. It was impressive then. The sucessor TA-E2000ESD was better in all parameters, much better sound. One bit pulse converters in three chips, each one for front channels, surround channels and last to Center and subwoofer, however, the aesthetics of the former liked more. This last one owned from 1992 to 1995. I miss them.
Hola , tengo uno igual , excelente preamplicador , saludos desde Chile
Just got this in near mint. Can’t wait to operate it.
Really nice piece of equipment
Well done ! Thank you !
Where can i get the "plugs-2 for the not unsed cinch holes ?
супер
Пожалуйста помогите!!!!! Как настроить уровень входного цифрового сигнала в Децибелах. Это под нижней крышкой слева Input level далее вниз Digital + - и плюсом минусом регулировать. Стояло на - 10 децибел. но звук тихий с приходиться ручкой прибавлять, тогда аппарат сильно греется. Меня это пугает. Сколько должно быть значение для его безопасной работы, что бы ему легко было. Спасибо. И У Вас он тоже сильно нагревается, особенно решетка сверху. СПАСИБО!!!!!!
Помогите с настройкой. Работает только в режиме долби сураунд.
NICE, i have one to sel, near MINT complete with NEW Original remote, and manuel, .....
Which speaker use ? than
k
I just purchased a esd2000 but the display doesn't work. Can someone in the NYC area repair it?
Try Hi Tech Corp @ 47 Canal street NY NY 10002
How do i connect this to speakers? Do I need amplifiers?
Yes, you do need speakers, this is just the pre-amp.
@@BABYGODZILLA2009 and an amplifier.
Kkkkkkjkk
Please, help!!!!! How to adjust the level of the digital input signal in decibels. This is below the bottom cover on the left of the Input level further down the Digital + - and the plus minus to adjust. Standing on - 10 decibels. but the sound is quiet with the use of a pen to add, then the unit is very hot. It scares me. How much should be the value for his safe work, what would it be easy for him. Thank you. And At you it too strongly heats up, especially a lattice from above. THANK YOU!!!!!!
Adjust the level to your liking ... If the input digital signal is clipping will appear a red light indicating it. ... Then you lower the input signal.
This preamplifier warms up well, do not worry, just keep it in a well-ventilated place
real time spectrum?
It is not spectrum, what it shows is the parametric equalizer curve set ..
This pre-amplifier has 3 digital parametric curves, where you can choose the center frequency and the slope (the slopes can be: two octaves, one octave, 1/3 and 1/12 per octave and gain of -12 to + 12 dB).
That is, what the video shows are the factory presets, where the preset add the type of reverberation like hall, theater, etc (and its not visible sets of early reflections, reverberation, seat distance etc .), equalization and compression (or expansion)
It is a very versatile preamplifier, considering it was released in 1991 !!