Very difficult on machine to control speed, slowly push down, sometime run away speed, other times I can just get it right.. what does the bolt for adjusting position of brake do? At 1:20 of video.
I'm not a tailor but I need this for engineering. It's white in colour so I'm assuming this is the electrical machine right? Is this basically the same setup principle for the manual foot pedal machine. You apply enough continuous downward force on the pedal and it would cause a rapid steady rotation??
Yes, an electric motor. By pressing the pedal, you compress the clutch disc and the engine disc together. The tighter they are pressed against each other, the higher the speed of rotation of the motor palley.
My motor started giving noise (like screwing with electric drill) when the pedal is released (un-pressed). Could you please tell me the reason? It was running fine for the last 15 years.
At 2:00 you say smaller pulley will increase speed. Absolutely the opposite. Think of the crank sprockets on your bicycle. You do not understand ratios.
Hi..my singer industrial sewing machine ..motor unable to stop when i turn switch on...what is the problem?
you are a gem for sharing this
Thanks for video, it really helped
Thank You
This was very informative, thank you!!!
Thank you!
Thanks very helpful
Thank you ❤❤❤
Can it provide power
do u have a video on repair of this, or brush changes etc?
Not yet, perhaps we will do it in the future.
Very difficult on machine to control speed, slowly push down, sometime run away speed, other times I can just get it right.. what does the bolt for adjusting position of brake do? At 1:20 of video.
When you take your foot off the pedal, the brake pads clamp the pulley and the machine doesn't sew, although the engine is running.
Myron po bang binebanta motor na ganyan kahit 2ndhan po
Nice vedio 👌👌
Very informative.
Do you have any advice on how to slowdown the machine without changing the pulley or motor?
A very strange question.
Do not press hard on the pedal. As a last resort, make a limiter
@@sewway Thank you.
So the other guys said smaller pully the slower it goes but stronger the stitch
I need moter clutch of this type how I should get
Online sewing equipment stores sell
What type of power chord does it use I got a PLK03BTA Mitsubishi it’ has a 220 v engine but does not come with cord
For a 220 volt network, a three-core wire is used. Phase, zero and ground. But it is better to turn to an electrician for advice.
Galle thiyeada may motor eaka
Saan mkkbili ng motor ng juki or mag pa rewind
I'm not a tailor but I need this for engineering. It's white in colour so I'm assuming this is the electrical machine right?
Is this basically the same setup principle for the manual foot pedal machine. You apply enough continuous downward force on the pedal and it would cause a rapid steady rotation??
Yes, an electric motor. By pressing the pedal, you compress the clutch disc and the engine disc together. The tighter they are pressed against each other, the higher the speed of rotation of the motor palley.
@@sewwayPerfect, I appreciate it 🙏
My motor started giving noise (like screwing with electric drill) when the pedal is released (un-pressed). Could you please tell me the reason? It was running fine for the last 15 years.
There can be many reasons, most likely the bearing is worn out. But the main reason is age
At 2:00 you say smaller pulley will increase speed. Absolutely the opposite. Think of the crank sprockets on your bicycle. You do not understand ratios.
Mag Kano Ang motor Ng makina
How much
Traduire en Français merci beaucoup
My motor is giving smoke
Hmach pric
smaller pulley will make it slower not faster.
Yes, that's right, in physics at school I had a bad mark
When the pulley is small, the speed is low
No, on the contrary
I installed a small pulley and the speed reduced, practical
Exactly, you are right, it seemed to me the opposite.
Clutchmotorindustrialaddress
Adress
Kanpurnagarupstate
We don't sell anything
haha lol