I wanted to do this for my rv and the inspector told me that romex could not be placed in conduit under any circumstances so I will have to just get a few rolls of stranded wire. good work!
This might be a dumb question but why do you have a single 50A breaker feeding a single 50A breaker? wouldn't it make more sense to just wire the cables you pulled to the second breaker right up to the socket? I think you would likely need a 70A breaker at the main panel feeding the panel with the 50A and the 20A breakers? Otherwise you would just need a socket fed from the main panel and you could save like half the cost.
You’re correct, it would be easier however you need a different gauge wire. I had on hand the proper wire for 50 amp and was not comfortable running 70 amp through it. It might be unconventional, but I can assure you it works.
Siding is a GAF composite mineral siding. If it was asbestos you would do the exact same install except vacuum with HEPA filter when drilling or just have someone spray with water. That will also knock down dust, you can also wear a mask or even respirator if you choose.
Isn't the 20 amp circuit normally fed from the same wire that feeds the 50(70)amp wire (through the 20 amp breaker) which feeds the 50 amp outlet. You don't have to run two separate sets wires do you? Did you just chose to do it that way. Just curious.
I did not want my 20 amp feeding off the 50/70amp. I chose to run separate lines and breakers mainly because I wasn’t comfortable running it the way you explained. Although I am very handy, I am not a licensed electrician.
@@derrich773 It already had breakers installed and prewired. I've got that same panel but haven't installed it yet, trying to find a decent deal on #6 or #4 THNN or THWN-2 simpull wire, as I'm going to run it 30-60' in flex or maybe gray pvc conduit. Thanks for posting. Safe travels!
@@rickl6697 . The best way to run this is to use 4/3 Romex, which will handle the 70amps, instead of running 2 lines of 6/3 and 12/2. But you will have to go to an electrical supply house to buy as neither Lowes nor Home Depot typically stock.
@@gojoe2446 I bought a 50/30/20 box that came pre wired. I want to buy wiring in advance. I am not installing it. I am not going to use the 50amp, my rv is 30 amp, I will cover 50 Amp plug for now, but since it's pre wired it will be able to be used if needed. I only want to do 50 Amp wiring, I will never use more power than that. Should I buy 6/3, the total run is about 35 feet, then do I buy ground stakes? Just wanting everything on hand. Should a 50 Amp fuse be installed at main box?
The spare 20 is purposely installed for the GFCI. Now the breaker for the GFCI is NOT readily accessible and within 30" in of the disconnect. You also have a GFCI breaker feeding a GFCI outlet which can lead to some real nuisance tripping due to the difference in milliamp trip ratings. When in doubt, always trust the factory wiring. Stay safe....
If you look t the bottom of that box it has a hole for a grounding cable to go down to a grounding rod. Why did you not do that? Isn't it code in your area?
Yes it comes wired already. All you have to do is wire it from your main panel using a 70amp breaker. I decided to wire mine differently but I wouldn’t recommend unless you are comfortable.
I wanted to do this for my rv and the inspector told me that romex could not be placed in conduit under any circumstances so I will have to just get a few rolls of stranded wire. good work!
This might be a dumb question but why do you have a single 50A breaker feeding a single 50A breaker? wouldn't it make more sense to just wire the cables you pulled to the second breaker right up to the socket? I think you would likely need a 70A breaker at the main panel feeding the panel with the 50A and the 20A breakers? Otherwise you would just need a socket fed from the main panel and you could save like half the cost.
You’re correct, it would be easier however you need a different gauge wire. I had on hand the proper wire for 50 amp and was not comfortable running 70 amp through it. It might be unconventional, but I can assure you it works.
Looks like a great job. Drilling in that old siding looks precarious. Hope it was not asbestos!
Siding is a GAF composite mineral siding. If it was asbestos you would do the exact same install except vacuum with HEPA filter when drilling or just have someone spray with water. That will also knock down dust, you can also wear a mask or even respirator if you choose.
Isn't the 20 amp circuit normally fed from the same wire that feeds the 50(70)amp wire (through the 20 amp breaker) which feeds the 50 amp outlet. You don't have to run two separate sets wires do you? Did you just chose to do it that way. Just curious.
I did not want my 20 amp feeding off the 50/70amp. I chose to run separate lines and breakers mainly because I wasn’t comfortable running it the way you explained. Although I am very handy, I am not a licensed electrician.
@@derrich773 It already had breakers installed and prewired. I've got that same panel but haven't installed it yet, trying to find a decent deal on #6 or #4 THNN or THWN-2 simpull wire, as I'm going to run it 30-60' in flex or maybe gray pvc conduit. Thanks for posting. Safe travels!
@@rickl6697 . The best way to run this is to use 4/3 Romex, which will handle the 70amps, instead of running 2 lines of 6/3 and 12/2. But you will have to go to an electrical supply house to buy as neither Lowes nor Home Depot typically stock.
@@gojoe2446 I bought a 50/30/20 box that came pre wired. I want to buy wiring in advance. I am not installing it. I am not going to use the 50amp, my rv is 30 amp, I will cover 50 Amp plug for now, but since it's pre wired it will be able to be used if needed. I only want to do 50 Amp wiring, I will never use more power than that. Should I buy 6/3, the total run is about 35 feet, then do I buy ground stakes? Just wanting everything on hand. Should a 50 Amp fuse be installed at main box?
The spare 20 is purposely installed for the GFCI. Now the breaker for the GFCI is NOT readily accessible and within 30" in of the disconnect. You also have a GFCI breaker feeding a GFCI outlet which can lead to some real nuisance tripping due to the difference in milliamp trip ratings. When in doubt, always trust the factory wiring. Stay safe....
If you look t the bottom of that box it has a hole for a grounding cable to go down to a grounding rod. Why did you not do that? Isn't it code in your area?
Are you a licensed electrician in NJ?
This is a Lotta hub-bub
The 50 amp plug is actually to legs of 50 giving you 100 .
what pipe size did you use?
I was wondering the same thing and when I took a screenshot of the fitting I seen 1 1/4" on it
Question please.
Does the pedestal come wired already so you don't have to worry about 240 going into RV? Only 120v is needed....
Thx
Yes it comes wired already. All you have to do is wire it from your main panel using a 70amp breaker. I decided to wire mine differently but I wouldn’t recommend unless you are comfortable.
@@derrich773 70 ? Its a 50 amp .....
@@ronsmith8434 he wired 50 and 20 seperate lines.
@@ronsmith8434the total amps in the box is 50 + 20 so the wire feeding it has to be the same or higher
No it doesn't!
No locknut on male adapter in your new panel. Otherwise, we’ll done.
When you think about it, how he has everything wedged, does that locknut give you anything?
Sorry Dude you're killing me with all of th ummm, ummm, ummm after every other word. Good info otherwise 😢