Convert Manual to Automatic Homemade Cradle Life Hacks Trick

amzn.to/3wJatoC
Amazing Automatic Cradle in Just 150 Rs Make fully automatic Cradle..
Automatic Homemade Cradle With Speed Controller

[@avinashbhagat2760]

Good work.. realy appreciate you to provide all details and reply to every comment with proper links..

[@urmilparikh883]

Do you have any thoughts for something similar for adult jhula? The ones we have in Gujarati homes?

[@technocracysimplified]

yes I have already made video on it. ruclips.net/video/IXV721FL9jY/видео.html

[@samyuschannelns7659]

Can u make one for me brother..

[@sonamariabaiju]

How yo buy

[@ruchishah2095]

This is very interesting. Can you please share the detailed assembly of the Speed regulator setup?

[@technocracysimplified]

Speed regulator I have manually prepared. You can also use this link : www.amazon.in/dp/B09FVCGSHM?

[@sushantpawar5635]

Can I use the above set up directly...just want to know more ..I am not that technically aware of it..thnks

[@rahulnarkhede7203]

Does 30 rpm will work ...Dont seem it will bee to Fast or Can i Install 10 rpm

[@technocracysimplified]

30 RPM will be difficult as you need optimum speed range to swing the cradle so 10 RPM will be best for it.

[@nousath24]

Can you mentioned motor model and RPM
And also regulator

[@technocracysimplified]

Motor DC Gear Motor 10 RPM.
www.electronicscomp.com/10-rpm-centre-shaft-dc-geared-motor-india?gclid=CjwKCAjwue6hBhBVEiwA9YTx8LfWqfCZ3XRhwIremDCjwi94zvhwQLUPwRRscKlKTDKYdtjvhfSGThoCkaIQAvD_BwE

[@feeling_learning]

Is moter ka price kitna h

[@technocracysimplified]

Rs. 185.. Link - www.electronicscomp.com/10-rpm-centre-shaft-dc-geared-motor-india?gclid=Cj0KCQjwgLOiBhC7ARIsAIeetVDIq8YIuqryTKXkU1jleWax2fodBmfJ6L7kWo2vOKm6Lk7i5LFJO44aAtPoEALw_wcB

[@PavanKumar-wq2hn]

Hi, Did not understand the reason behind the second MDF piece mentioned at ruclips.net/video/xsSF5-ArMhQ/видео.html . Could not figure out how this is preferable against a straight one? It is attached with one screw which would not remain intact after some usage - is this needed to be free of fixed at 90 degrees permanently? Could you please share more details or links to know about this? I am in process of building a similar solution and your input greatly helps.

[@technocracysimplified]

Thank you for your Question!!
Purpose of making this at 90 angle is increase centrifugal force and reduce tension to MDF piece later on I have replaced this piece with PVC plastic piece to improve it. You can make it straight but you need to use steel rod and high torque motor for the same.

[@PavanKumar-wq2hn]

Thanks a lot for the response. I made one with 30RPM Johnson motor fixed with a 4*10cm wheel. Radius increased by fixing an L clamp to wheel and further extending it with a vertically cut section of PVC pipe. It kind of works, but motor is not fixed in a stable way and jerks at positions of high torque causing jerks in the cradle. Need to work on the jerks in order to have a smooth operation. May be I'll try the 90 degree approach too.

[@technocracysimplified]

Thank You and Good Luck!!

[@jaybhatt09]

@@PavanKumar-wq2hn I am also preparing a prototype and hopefully it works well. Let me know if I can help in any way

[@mehboobbaig8817]

I want to buy

[@technocracysimplified]

Nor for Sale!!

[@sheetaljadhav7047]

Did u sale the machin.... This is for sale

[@technocracysimplified]

Thanks for comment..No it is just for innovation purpose...