Your turbo oil drain MUST be at the bottom. You only need to loosen the bolts that clamp the turbine and compressor housings and you will be able to rotate the centre housing. I see others have mentioned a oilfeed restrictor. I use the same turbo on a bike which has 60psi oil pressure and have a 1mm restrictor in the oil supply line. If you do these mods the smoke should disappear. Nice job on the bike
@@Rosteripulla it's alot different from a car right? I never through bike with turbo because i throught it was only for cars because thats what I do can u please tell me how so that I can also do to bikes i have a garage
the amount of boost he is making for the size of the motor and valve count is respectable. I have a 180cc 4v makes more boost but that comes down to turbo sizing. great vid.
For the people claiming it isnt making boost 1- the gauge is in bars i think.. meaning he is making 2-3 psi from what i saw. 2- give him credit. some people slap plastic turbines on their cars in the name of science. when the question has already been answered. it doesnt work. If anything the fake turbos reduce air into an engine XD, but this little motors can be boosted with the right setup. if u watch the gauge he does make boost, and an engine doesnt jump to the limiter like that n/a ahahaha
@sourand jaded Does this result in an increase in preformance? i thought i was seeing 3 psi maybe no? Im not an expert but it looked to be working to me.
@sourand jaded I think i see what you mean now after slowing down the video. so in basic terms what does that mean? why does it need a plenum for boost? Is it because there is nothing for pressure to build, so it just jets straight in? Again not an expert but i think your saying its not making boost because it cant build enough pressure?
@sourand jaded To my understanding, the timing in a 3-cylinder is even better than in a 4-cylinder... But a 2stroke-variable-lenght-resonance-chamber is easier and cheaper to make, in order to keep boost of a single cylinder always at optimum... ruclips.net/video/0odVzSgufjk/видео.html Automatic system ruclips.net/video/xgj-_vdcO7w/видео.html 12:35 manual system (he changes the buffle-position with a screwdriver, but it´s a proof-of-concept for you to watch)... Chamber-rear-buffle has been moved by 3cm for each run, so torque stays at maximum, but for a higher rpm at each run. Conclusion, by moving the chamber, or even solely the chamber´s rear-buffle, you can match the exhausts resonance-length in a way, that you always have optimal, total combustion (always functioning in resonance with the expansion-chamber, at any rpm, means, that no fuel escapes unburnt through the exhaust anymore), and maximal boost... With simple low-tech, no turbo or cylinder-head-valves needed.
I am a turbocharger manufacture from China. I like your video. This turbo is used on Suzuki JIMNY. It's a very nice choice. It's almost the smallest turbo I have ever seen. My suggestion is to put the turbo under your engine. The engine oil must gose into the turbo BEFORE it starts to work.
G'day from West Australia, 😉 Think your turbo needs an oil restrictor in the feed line. If you do have one it needs to be a lot smaller. Otherwise you engine sump will end up dry, and a blown up motor with no bearings left. Otherwise nice build, 2 thumbs up from me 🙂👍👍
In addition to other comments. I also noticed what looked like the air bubles in the turbo drain going upwards. It might be that there's back pressure in the crank case which is pushing vent air back through the inlet side of the turbo bearing slip rings. A idea to would be to run the drain into a bucket for 30 seconds (don't run out of oil!) and see if it made a difference.
It would be better if you share the results of before and after, 0-100 km or 0-60 miles, time Liter/km or gallon/mile Operation temperature of engine and etc.. But also it was a good video thank you dude.
Looks like the turbo has a dynamic seal for use above the throttle valve not the carbon seal needed for use downstream of the throttle/carburetor.......meaning it will be sucking oil in thru the turbo seal and into the motor whenever its not making boost pressure.
Everyone is talking about oil burning that is caused wrong angle or wrong size of oil feed & drain... But the real reason is that thraw through turbo setup issue is that when carburetor is closed, intake vacuum starts to suck oil from turbo to intake... These style setups need carbon axle seal in compressor...
Я лет 5 назад делал подобный проект на турбине ihi 31, мотор так же дымил, пришел к выводу, что нужно ставить дроссель между головой и турбиной, который дублировал бы открытие карбюратора, но к тому моменту у меня уже кончились силы)
Damn that’s cool, wonder how much boost you could run on propane with liquid phase injection into the intake (liquid to gas expanding would have a big cooling effect too coupled with the high octane). Or even n/a with maxed out compression ratio to take advantage of it for efficiency,
nice, really pretty. I would get the turb near the exhaust rather than the intake. I'll get the carb after the compressor. I' would intercool it, you know, 'cause is cooler.
The turbocharger that Honda used on their 500/650 twin back in the day was much smaller than the one you are using. If I recall correctly, the impeller was about the diameter of a nickel. The turbo HAS to be small so that the exhaust gases (minimal as they are) can actually make the rotating assembly spin fast enough to create usable boost.
What's the A/R ratio of the turbo you chose and the impeller size? For a 125cc engine to not induce excessive turbo lag in my experience, you would need the NLA IHI Brand 17mm turbo with a computer controlled electronic wastegate, as this would be the only type that could respond quickly enough to the input signals of this tiny engine. If we go back 30-odd years, Honda had fits with their original CXT500 turbo in what '83 with a 33mm turbo? When they upped the engine displacement to 643cc's in '85 and the turbo to a 35mm and went to a full electronic fuel injection management system, it became a docile, fine running roadster competent to almost any liter plus Superbike sold, with superb handling due to it's lighter weight and mass centralization.
Currently I'm quitting my everyday job to do RUclips full time. Help me to achieve my dream, join my Patreon link: www.patreon.com/crazyyuri Watch 2nd Video about this TURBO bike: ruclips.net/video/tjyAlddhXbg/видео.html Buy this TURBO kit: s.click.aliexpress.com/e/_9IypRv
to raise the boost more you could delay the ignition and when it goes up give it 20 degrees... draw turbo in those applications is the best... you could also puncture the rubber tube of the wastegate to increase the boost... 💪💪💪
how to make vehicles run on alkali solution, ammonia solution, alcohol solution: electrolysis (can be fuelcell dry/wet hho, radio frequency hho, or plasma hho generators) inside fuel filter (injection vehicles) or big custom float bowl (carburetor vehicles) , and inside combustion chamber by plasma from multi sparkplugs, water laser ignition sparkplugs, we need hack the electrycity by change regular stator/altenator with high current one, then adding air scoop with wind turbine electric generator (all land, sea and aviation vehicles can use it as external electic current generator) inside it and put alternator on propeller shaft or axle (for cars, truck and other wheelers vehicles) and electric motor stator generator inside center of rear velg and front velg (for cars, motorcycles) this guaranteed free energy by movement of vehicles and wind that come from front of vehicles, then use supercapacitor in hydrogen generator connection cable and varistor in coil-ignition sparkplugs cable, then make electrolysis inside fuel filter first electrolysis (pem or plasma hho or by radio freq hydrogen generator), because grafity effect, water inside fuel filter or float bowl will make pressure so hydrogen don't come back to fuel tank come down but up right into injector or carburetor fuels spray, by injecting or spraying both hydrogen and water into internal combustion chamber chain reaction (explosion by next electrolysis stage must been happening inside combustion chamber) plasma sparkplugs or water laser ignition sparkplugs will make electrolysis+ignition , the principle is same like lightning strike on sea (natural electric plasma electrolysis) that convert sea water into hydrogen and oxygen + make pressure at sea water then burn it cause by lightning strike hit hydrogen (explosion of water on sea by lighting strike) on it this mean all vehicles actualy can run and burn on water and hydrogen, the scheme will same to fuelcell electric vehicles which when inside i.c.e engine we burn hydrogen and water in fcev we just injecting hydrogen from electrolysis right into fuelcell
The reason for the smoke is that these turbo's have the incorrect type of seal on the shaft into the compressor housing. And what is happening is when the engine is at idle or off throttle eg: under vacuum, it's sucking oil through the turbo shaft seal. I know this as I used the same turbo years ago on a 140cc thumpster. Remove the turbo and you will find excessive amount of oil in the intake port and turbo outlet. Not sure if there is a turbo this size that has the correct seal type to be under negative pressure. Great build though! Very neat!!
Dude, that is so friggin awesome. I what to hook up my mini bike with a turbo like you did, it is a 212cc predator engine. I love what you did with your 125cc.
It'll be more work because you'll need an oil pump and external power source for it..., the predator and other pull start engines of that size are splash lubricated. It is doable though.
You have to increase the jet size in the carb otherwise it’s pointless. You’re forcing more air into the cylinder so you need more fuel to make a bigger bang in the cylinder.
As soon as you took the rotary tool to the frame in Australia it would be written off. Not mentioning you have to get it re-engineered if you change the induction of an engine here as we
excelent work but you need to change the rubberpipes that you installed for engine oil they will melt by the heat of bike because pipe is close to engine clutch side and it always heats more than magnet side.
All that smoke is your turbo oil seals failing due to your turbo oil drain angle. Point it as much downward as possible so that the oil has a place to evacuate after it is done lubricating the journal bearing.
The work is interesting. More studies would have been necessary to achieve something consistent. By instance a turbo always needs a vertical oil feed from top to bottom to avoid oil consumption (smoke and possible turbocharger destruction). Also it doesn't reach its functional rotation speed. Good try and best of luck for the next project.
You’re getting just over 0 bar of boost. I’m going to be generous and give you 0.3 Bar, so around 4 and a bit PSI of boost pressure. You’d get more from ram air induction. Did you increase the size of the jet in the carb to account for the extra oxogen ?. Personally you’d be better using a bottle of compressed air or oxogen instead of a turbo on a 125 CC bike. That’s what I would do and use a regulator so you can turn up the boost. If you use compressed oxogen it would not need be to under pressure since the goal of compressors is to force more oxogen in the engine but with pure oxogen gas it could just be a trickle of gas since it’s 100 % oxogen or instead use nitrous oxide. Either one will do what that turbo can’t.
Kezdetnek nagyon jó. Mivel szinte csoda, hogy beindult. De ezek után apró modosításokkal lehetne még rajta elég sokat fejleszteni. Pl. Turbo helyett elektromos kompresszor, Üzemanyag / Levegő keverési arány, Rendesen kapjon hűtést, stb.
Big mistake with exhaust. The exhaust need bubbles to work the engine good with the best power. The power of 2strokes engines coming the 70% from the exhaust system. Make a good exhaust system and you will take more power. And something more, make boyesen reeds valve. This engine can reach to 20 and maybe more hp. Good Work!!!
went from 7 HP to 9 HP. Almost 30% power increase. . . Amazing
Where did you find out the it went from 7 to 9? I missed that part...
Goes from 7 HP to 9 HP
Gets turbolag :/
Hey the bike hp is 196+turbo200hp=396hp total
@@ODGAMER76 🤭
@@klausbrinck2137 há então aí também tem os sabe tudo 😏😏😏
It's great seeing the quality of your camera work, editing and builds increase every video. Keep it up!
Thank you, Ivor!
@@crazyyuri it is great.. you should give your camera man more credit!
@@bmint and editor 💪
And himself for sure
Это не его видео он его украл
Your turbo oil drain MUST be at the bottom. You only need to loosen the bolts that clamp the turbine and compressor housings and you will be able to rotate the centre housing. I see others have mentioned a oilfeed restrictor. I use the same turbo on a bike which has 60psi oil pressure and have a 1mm restrictor in the oil supply line. If you do these mods the smoke should disappear. Nice job on the bike
You can't with that turbo, it's a cheap turbo
I was looking for this comment
@@NOONE-hp8bw Clearly you can. It has symmetrical screw spacing, meaning you can rotate the turbo as you please.
@@Rosteripulla it's alot different from a car right? I never through bike with turbo because i throught it was only for cars because thats what I do can u please tell me how so that I can also do to bikes i have a garage
@@zeomac2511 The turbo doesn't care what it's attached to. Car, bike, lawnmower, same thing.
The sheer joy on your face when it finally kicks over is priceless! Nice workmanship!
Is it really 'nice workmanship'?? How the hell would you know, you never saw the bike actually run down a road.
@@aussiehardwood6196 u must be really fun at parties
0.5hp and it burn alot of oil. 1liter of oil : 150km
The way your face lit up when the engine fired up, that's classic, like a big kid. LOL
Always good to see people enjoying what they do.
the amount of boost he is making for the size of the motor and valve count is respectable. I have a 180cc 4v makes more boost but that comes down to turbo sizing. great vid.
What turbo are you running?
For the people claiming it isnt making boost 1- the gauge is in bars i think.. meaning he is making 2-3 psi from what i saw. 2- give him credit. some people slap plastic turbines on their cars in the name of science. when the question has already been answered. it doesnt work. If anything the fake turbos reduce air into an engine XD, but this little motors can be boosted with the right setup. if u watch the gauge he does make boost, and an engine doesnt jump to the limiter like that n/a ahahaha
@sourand jaded Does this result in an increase in preformance? i thought i was seeing 3 psi maybe no? Im not an expert but it looked to be working to me.
@sourand jaded I think i see what you mean now after slowing down the video. so in basic terms what does that mean? why does it need a plenum for boost? Is it because there is nothing for pressure to build, so it just jets straight in? Again not an expert but i think your saying its not making boost because it cant build enough pressure?
@sourand jaded so basically the charge pipe/plenum serves as an area to build boost correct? Im not nearly as educated I understood like half of that.
@sourand jaded I have seen a video of a 125 making 15 psi it looked wicked. Dude was on ice too
@sourand jaded To my understanding, the timing in a 3-cylinder is even better than in a 4-cylinder... But a 2stroke-variable-lenght-resonance-chamber is easier and cheaper to make, in order to keep boost of a single cylinder always at optimum...
ruclips.net/video/0odVzSgufjk/видео.html Automatic system
ruclips.net/video/xgj-_vdcO7w/видео.html 12:35 manual system (he changes the buffle-position with a screwdriver, but it´s a proof-of-concept for you to watch)... Chamber-rear-buffle has been moved by 3cm for each run, so torque stays at maximum, but for a higher rpm at each run.
Conclusion, by moving the chamber, or even solely the chamber´s rear-buffle, you can match the exhausts resonance-length in a way, that you always have optimal, total combustion (always functioning in resonance with the expansion-chamber, at any rpm, means, that no fuel escapes unburnt through the exhaust anymore), and maximal boost... With simple low-tech, no turbo or cylinder-head-valves needed.
I am a turbocharger manufacture from China. I like your video. This turbo is used on Suzuki JIMNY. It's a very nice choice. It's almost the smallest turbo I have ever seen. My suggestion is to put the turbo under your engine. The engine oil must gose into the turbo BEFORE it starts to work.
With turbo in place I think you need to change the timing of your cylinder to eliminate the white smoke. This is actually inspiring.
The force is strong with those mastering MIG!
G'day from West Australia, 😉
Think your turbo needs an oil restrictor in the feed line.
If you do have one it needs to be a lot smaller.
Otherwise you engine sump will end up dry, and a blown up motor with no bearings left.
Otherwise nice build, 2 thumbs up from me 🙂👍👍
Looks like the oil pressure is pushing it up from the drain and burning it in the turbo. Maybe a check valve in the drain line.
His engine needs a rebore after this look at the smoke on his engine lol
Go perth woo
Just found this, thanks RUclips. G'day from WA too.
For every 5 gallons of gasoline consumed, 1 gallon of oil is also consumed. 🤣 Just kidding. 🤣🤣 Greate build and video. G'day from serbia
3:50 was a great shot, even with a little bike participation. cool project!
The oil drain should be straight down and you need a "boost chamber" a intake 4 times bigger than engine's cc
I think he wants it to be reliable.. those are great tips for performance!
Νο plenum in draw through setup. Only in blow through 😉
@@zezeNoPro you need a plenum in both
I guess a burnout is necessary in any engine modification video...
Good job, thumbs up!
In addition to other comments. I also noticed what looked like the air bubles in the turbo drain going upwards. It might be that there's back pressure in the crank case which is pushing vent air back through the inlet side of the turbo bearing slip rings. A idea to would be to run the drain into a bucket for 30 seconds (don't run out of oil!) and see if it made a difference.
I loved the clean oil lines. Nice little project. Reminds me of the old Honda Turbo. 😎
How about applying it to the Honda Vario/Click 125cc FI, This is a cvt scooter i like it.
It would be better if you share the results of before and after,
0-100 km or 0-60 miles, time
Liter/km or gallon/mile
Operation temperature of engine and etc..
But also it was a good video thank you dude.
He made very cool, way rideable, 80's rock star smoke machine!🎸👍
Its amazing how he made that bike with a turbo keep it up bro. Keep doing what you love 💪🏻😊
L k
Vou
Hay man cool bike that thing rips !! All the best!! Subscribed and liked 🤙🏻
Looks like the turbo has a dynamic seal for use above the throttle valve not the carbon seal needed for use downstream of the throttle/carburetor.......meaning it will be sucking oil in thru the turbo seal and into the motor whenever its not making boost pressure.
Ah, so that's making it smoke
Such an insanely cool video, simple but so interesting, keep up the great work!
the Engine is not 125, it was changed for a Daytona 190cc.
Nah yx160 cc
Mad Respect to your project and mad respect to your video.
I love classic motors so much !!!
Everyone is talking about oil burning that is caused wrong angle or wrong size of oil feed & drain... But the real reason is that thraw through turbo setup issue is that when carburetor is closed, intake vacuum starts to suck oil from turbo to intake... These style setups need carbon axle seal in compressor...
Я лет 5 назад делал подобный проект на турбине ihi 31, мотор так же дымил, пришел к выводу, что нужно ставить дроссель между головой и турбиной, который дублировал бы открытие карбюратора, но к тому моменту у меня уже кончились силы)
Прикол в том что видео "своровано" с канала MotoCor помоему.
Поправочка это его другой канал, сори)
Well done Yuri.
Best regards from Mexico "tovarich"!
Damn that’s cool, wonder how much boost you could run on propane with liquid phase injection into the intake (liquid to gas expanding would have a big cooling effect too coupled with the high octane). Or even n/a with maxed out compression ratio to take advantage of it for efficiency,
The most pimped up 125 I’ve seen. And the rear shocks. And that grin at 3:00 epic
it is a 160cc engine. Watch the original video from the author
Great video, good videomaking and mechanic 😉
thak you for this wonderful gift to society my man
now the top speed of the bike to see how much it goes up
It's crazy but awesome, congratulations!!!
Awesome pipes. What jets did you end up with? Did your pilot stay more or less the same?
nice, really pretty.
I would get the turb near the exhaust rather than the intake.
I'll get the carb after the compressor.
I' would intercool it, you know, 'cause is cooler.
That's awesome! How much of a performance increase did you feel on the bike?
Lots more smoke. Woot?
The turbocharger that Honda used on their 500/650 twin back in the day was much smaller than the one you are using. If I recall correctly, the impeller was about the diameter of a nickel. The turbo HAS to be small so that the exhaust gases (minimal as they are) can actually make the rotating assembly spin fast enough to create usable boost.
Beautiful welds 😝
Wish I had a 1/4 of your skills ,and your not afraid to try! Amazing!!
What's the A/R ratio of the turbo you chose and the impeller size? For a 125cc engine to not induce excessive turbo lag in my experience, you would need the NLA IHI Brand 17mm turbo with a computer controlled electronic wastegate, as this would be the only type that could respond quickly enough to the input signals of this tiny engine. If we go back 30-odd years, Honda had fits with their original CXT500 turbo in what '83 with a 33mm turbo? When they upped the engine displacement to 643cc's in '85 and the turbo to a 35mm and went to a full electronic fuel injection management system, it became a docile, fine running roadster competent to almost any liter plus Superbike sold, with superb handling due to it's lighter weight and mass centralization.
Kawasaki made a turbo bike also back then i think
got a link for that turbo
Engine yx 160 (160cc), not 125cc
Christ... Rough. Really rough. a DCMT insert to screwcut, chewing gum welds and a turbo oil drain uphill. Genious.
Es buena idea pero cabe el problema de sobrecalentamiento o que se funda los pistones por el estrés que lo lleva
Hola sabes que turbo es se ve pequeño y quiero hacer algo así,un saludo
I don't care about the smoking tires part of it but I would like to see a before and after on a Dyno machine or even acceleration tests or something.
¿Y de mejorar esos frenos de tambor después de aumentar la potencia del motor?
REALLY fantastic video! much love
its burning oil bad ! turbo seals ?
The simplest and lightest power increase: a two stroke 125 cc. Italian engine (Aprilia, Cagiva, Gilera, Honda...)
Anyway, this is a really great work
Honda is now Italian? Thats new to me and i think its actualy easier and more fun to Turbo a little chinese 125 instead of engine swapping it.
Top speed??
タービンオイルの潤滑は、一定の圧力を常に掛けないと密閉が保てず、隙間からオイルが排気側に流れて煙が出る
How much HP has the engine after installing the turbo booster?
214
That thing will torture your 125 engine. Lean mixture - more air,less fuel - hot as hell.
But you really did a nice work.
Currently I'm quitting my everyday job to do RUclips full time. Help me to achieve my dream, join my Patreon link: www.patreon.com/crazyyuri Watch 2nd Video about this TURBO bike: ruclips.net/video/tjyAlddhXbg/видео.html Buy this TURBO kit: s.click.aliexpress.com/e/_9IypRv
to raise the boost more you could delay the ignition and when it goes up give it 20 degrees... draw turbo in those applications is the best... you could also puncture the rubber tube of the wastegate to increase the boost... 💪💪💪
Yuri... Look at the views, we want to see more of the turbo engine.
how to make vehicles run on alkali solution, ammonia solution, alcohol solution: electrolysis (can be fuelcell dry/wet hho, radio frequency hho, or plasma hho generators) inside fuel filter (injection vehicles) or big custom float bowl (carburetor vehicles) , and inside combustion chamber by plasma from multi sparkplugs, water laser ignition sparkplugs, we need hack the electrycity by change regular stator/altenator with high current one, then adding air scoop with wind turbine electric generator (all land, sea and aviation vehicles can use it as external electic current generator) inside it and put alternator on propeller shaft or axle (for cars, truck and other wheelers vehicles) and electric motor stator generator inside center of rear velg and front velg (for cars, motorcycles) this guaranteed free energy by movement of vehicles and wind that come from front of vehicles, then use supercapacitor in hydrogen generator connection cable and varistor in coil-ignition sparkplugs cable, then make electrolysis inside fuel filter first electrolysis (pem or plasma hho or by radio freq hydrogen generator), because grafity effect, water inside fuel filter or float bowl will make pressure so hydrogen don't come back to fuel tank come down but up right into injector or carburetor fuels spray, by injecting or spraying both hydrogen and water into internal combustion chamber chain reaction (explosion by next electrolysis stage must been happening inside combustion chamber) plasma sparkplugs or water laser ignition sparkplugs will make electrolysis+ignition , the principle is same like lightning strike on sea (natural electric plasma electrolysis) that convert sea water into hydrogen and oxygen + make pressure at sea water then burn it cause by lightning strike hit hydrogen (explosion of water on sea by lighting strike) on it this mean all vehicles actualy can run and burn on water and hydrogen, the scheme will same to fuelcell electric vehicles which when inside i.c.e engine we burn hydrogen and water in fcev we just injecting hydrogen from electrolysis right into fuelcell
Was it really worth it????
The reason for the smoke is that these turbo's have the incorrect type of seal on the shaft into the compressor housing. And what is happening is when the engine is at idle or off throttle eg: under vacuum, it's sucking oil through the turbo shaft seal. I know this as I used the same turbo years ago on a 140cc thumpster. Remove the turbo and you will find excessive amount of oil in the intake port and turbo outlet. Not sure if there is a turbo this size that has the correct seal type to be under negative pressure. Great build though! Very neat!!
Love it. Good wheelie and an even better burnout. And she looks real pretty too.
That's crazy amazing bru hahaha love the video.
Very nice nine horse power, you're the man
My 125 Honda shine already produces 10.7 bhojpuri 💁 but you are juss WoW 😲
Dude, that is so friggin awesome. I what to hook up my mini bike with a turbo like you did, it is a 212cc predator engine. I love what you did with your 125cc.
It'll be more work because you'll need an oil pump and external power source for it..., the predator and other pull start engines of that size are splash lubricated.
It is doable though.
Looks cool man. Just clock that turbo so your feed is on top and your drain is on the bottom!
最近地球が暑いのはこのせいかもしれませんが、
個人的には大好物です
Every postman needs this turbo mod.
You need to reclocl the center section. Oil inlet should be on top. That's why it's smoking so much.
Cool looking build though.
Very nice work! But as others have said, the oil drain should be pointing down, the smoke is from the turbo not draining properly
Вот это ты рукастый👍🏻👍🏻👍🏻
Видео с канала Moto Kor
You have to increase the jet size in the carb otherwise it’s pointless. You’re forcing more air into the cylinder so you need more fuel to make a bigger bang in the cylinder.
Brother man, that was awesome 👍😎
Pure fun, amazing vid!
Awesome ! Create easy turbos to you movement tech. More Air is free material
Its so good because a 2 stroke needs a special exhaust to funktion properly
Worst thing ever!
Is I will never get a chance to drive this inspirational peice of motorcycle engineering.
As soon as you took the rotary tool to the frame in Australia it would be written off.
Not mentioning you have to get it re-engineered if you change the induction of an engine here as we
You are a very good engineer, love your crazy projects.
😆
excelent work but you need to change the rubberpipes that you installed for engine oil they will melt by the heat of bike because pipe is close to engine clutch side and it always heats more than magnet side.
All that smoke is your turbo oil seals failing due to your turbo oil drain angle. Point it as much downward as possible so that the oil has a place to evacuate after it is done lubricating the journal bearing.
Excellent video sir.
Excellent build!
Рукастый
Красавчик👍
The work is interesting. More studies would have been necessary to achieve something consistent. By instance a turbo always needs a vertical oil feed from top to bottom to avoid oil consumption (smoke and possible turbocharger destruction). Also it doesn't reach its functional rotation speed. Good try and best of luck for the next project.
this really inspire me, thanks a lot
All 125 cc bikes should come with this
That's insane! I love it!
My hero
Job well done
Nice Work. Thanks from Germany.
How much of a increase in jetting did you need? Did you add a bigger carb or is that the stock one? What's with all the smoke??
Well because you need to decrease compression ratio anyway probably not a huge jump. Probably 5%-10% bigger jet.
Your music and style like my DEN VAU singer. : )
amazing creatifity bro..
You’re getting just over 0 bar of boost. I’m going to be generous and give you 0.3 Bar, so around 4 and a bit PSI of boost pressure. You’d get more from ram air induction. Did you increase the size of the jet in the carb to account for the extra oxogen ?. Personally you’d be better using a bottle of compressed air or oxogen instead of a turbo on a 125 CC bike. That’s what I would do and use a regulator so you can turn up the boost. If you use compressed oxogen it would not need be to under pressure since the goal of compressors is to force more oxogen in the engine but with pure oxogen gas it could just be a trickle of gas since it’s 100 % oxogen or instead use nitrous oxide. Either one will do what that turbo can’t.
Love the engineering man, soo cool!
Под турбирование нужно либо поршень с так называемой лужей, или хоть разжать камеру сгорания. А в целом отличная работа!
Now the engine was upgraded to 4 horsepower. 🤣
Just kidding. You did a very good job.
love your content bro! keep it up u deserve a subs and a like 🤗
Your turbo core is 90deg out. Oil drain needs to be at the bottom, which is why you have smoke. Rotate turbo core!
Really hope in other videos, there are some comments about what you are doing.
How crazy awesome is that!
Kezdetnek nagyon jó. Mivel szinte csoda, hogy beindult.
De ezek után apró modosításokkal lehetne még rajta elég sokat fejleszteni.
Pl.
Turbo helyett elektromos kompresszor, Üzemanyag / Levegő keverési arány, Rendesen kapjon hűtést, stb.
need a plenum so it can have stable boost, with that short and small volume intake turbo is hitting surge when making boost due to boost spike
Big mistake with exhaust. The exhaust need bubbles to work the engine good with the best power. The power of 2strokes engines coming the 70% from the exhaust system. Make a good exhaust system and you will take more power. And something more, make boyesen reeds valve. This engine can reach to 20 and maybe more hp. Good Work!!!
From which vehicle you had taken that turbo
За музыку отдельный респект ! )) а идея с турбонагнетателем.. прикольная ;-)
Он украл это видео с канала moto cor
@@Nadeshdinstn , это он и есть, но канал для англоговорящих.
Super job!