With this programmer you can read data from memory chips and also load this data. In total, it supports 34790 different chips. You can program microcontrollers. You can also check logic chips. In the video, I read data from a 24c64 chip and loaded other data
Hi, thanks for the info. Can Xgecu T48 replace Tl866II? I am working with a Pic controller and working with a Tl866II. If I buy Xgecu T48 will I be able to work with Pic controller?
I’ve downloaded the software, and I get the same message every time. “Windows cannot complete the extraction The destination file could not be created. Error 0x800704C7
Great video. Do you know the correct was to connect the alligator clips (Clip adapter) 2 pair on each side equaling 8 wires. I'm using the T48. The chip is still on the system board, by the way My experience level is 1 out of 100 Thank you
Main thing to note is matching all the pin 1 together. On the chip, there is a dot that indicates pin 1 (some chips have multiple from the molding process, but there will generally be a distinct one). On the clip, look at the wires and the red wire indicates pin 1. On the adapter board, the side the clip cable plugs into will indicate pin 1 with numbers or a dot. On the programmer, there's an arrow showing you where you should align the board and where pin 1 is. If you match all of these up, you should have the correct connection. Note some chips have a notch on the short side instead of a dot next to pin 1. In this case align your clip so pin 1 is on the side where the notch is.
With this programmer you can read data from memory chips and also load this data. In total, it supports 34790 different chips. You can program microcontrollers. You can also check logic chips. In the video, I read data from a 24c64 chip and loaded other data
Hi, thanks for the info. Can Xgecu T48 replace Tl866II? I am working with a Pic controller and working with a Tl866II. If I buy Xgecu T48 will I be able to work with Pic controller?
Works with PIC10-PIC18
@@Kositsyn83 Thank you very much. Can I buy from the link you posted?
I’ve downloaded the software, and I get the same message every time. “Windows cannot complete the extraction
The destination file could not be created.
Error 0x800704C7
Tms320f28035 lqfp64, Atmega88pa smd ic support??
Also it's read protect ic?
Please sir guide
1:53
Great video.
Do you know the correct was to connect the alligator clips (Clip adapter) 2 pair on each side equaling 8 wires. I'm using the T48. The chip is still on the system board, by the way
My experience level is 1 out of 100
Thank you
Main thing to note is matching all the pin 1 together. On the chip, there is a dot that indicates pin 1 (some chips have multiple from the molding process, but there will generally be a distinct one). On the clip, look at the wires and the red wire indicates pin 1. On the adapter board, the side the clip cable plugs into will indicate pin 1 with numbers or a dot. On the programmer, there's an arrow showing you where you should align the board and where pin 1 is. If you match all of these up, you should have the correct connection.
Note some chips have a notch on the short side instead of a dot next to pin 1. In this case align your clip so pin 1 is on the side where the notch is.
@@caralynx ah ha! I appreciate you taking the time to help me. I see what you mean. I will give that a try. Thank you and God bless you
Have you tried with GAL? Able to program GAL16V8D?
It's listed in the software
is this device fine for EMMC work?
It does support EMMC but you'll need an adapter
Hi can program this EPROM tms27pc256 20nl
It's listed in the software