I have 2 suggestions. Put a submersible water heater in the basin so you have hot water and add a rust inhibitor to the water, so parts don't rust right away after cleaning.
Thanks for the tips! We had the rust inhibitor put inside the besen already after the vid. Maybe hot water would be an option! Thank you again for the tip!
Yeppirs, excellent work there. An abrasive option for all surfaces would be Baking Soda. Works very well and bounces off of rubber and actually cleans bearing surfaces. To test the amount of soda to add, i would suggest using an old wheel bearing (needle bearing style) with micrometer measurements before and after. Then test a ball bearing style the same way to adjust the water-to-soda ratio. We melted 6 K-Cup microscreen filters together end-to-end and used as inline return water filter to keep debris from going back into the pump. Nice job my friend -- good luck!
Mantap ahh bang mad,buat sendiri je mesin ni,diy tak payah abis beribu nak beli mesin fungsi serupa,pakai tong dram je,gunakan 100% kreativiti sendiri.❤❤👍
I clicked thumbs up on this video because you have the blade protector installed on your angle grinder. That's how you know you're dealing with professionals. 👍
ni mamat ada gaya suka DIY untuk kegunaan kedai... bagus dan kreatif... elok lepas ni buat Custom Modification Motosikal... ala² American Chooper.... kan bagus gitew....
Use a dirty water pump because it wont be damaged by the blasting media in the water. The compressed air is what gives it the power but might need more air flow?
Terbaik bang buat wet blasting sendiri.....rasa mcm nk Diy sendiri jgk untuk bengkel kereta saya jgk...untuk kerja² membersihkn head dan lain² komponen...nice idea bang🙏🏻👍🏻
Kemas hasil kerja bang..Bang buh rain water repellent kereta yg murah bang kat cermin..biar air x melekat kat cermin..baru clear mata memandang time basuh barang..
@@AhmadKhan66Patutlah upah cuci aje sampai 1K...Kalau cuci pakai manual sahaja rase mcm nk baling scraper ke dinding😂...Kalau saya yg cuci kaedah manual pun rase fedup jugak...Hahaha
Nice idea to use a barrel for this project 😀👍. It helps a lot if you use dishes soap or industrial cleaner soap. This will help dissolve the oil residue 👍 I would use a different type of pump... a impeller pump like that is high volume / low pressure and if you reduce the pipes like in the video volume and pressure go down because of the impeller.
Are you just using straight water to blast those parts. Need a filter in your sump pick up.. Not bad. That's a cheap way to make a high pressure washer. What kind of spray nozzle are you using?
Watching this brought to mind Albert Einstein's maxi - make it as simple as possible, & no simpler. This was very quick & easy to build -if you know how - & cheap. & effective. What more could you ask for? Try wiping the view-port with dishwashing liquid to avoid misting. Or rub it with a cut potato.
Impressive :) , Tried building these multiple times and its like my sandblasters works 50% of the time rest of the time doesn't even following basically same builds as others. They are really handy to have
If you have a pressure washer you can get an adapter to use with it to use it for sand blasting. Only thing is you have to remember to keep the sand sucking hose above the nozzle so water doesn't leak back n get the sand wet n gumm up.google. pressure water adapter to sand blaster adapter.
Super quick easy method of cutting straight lines in drums, 1 quick drill hole as starting point, then broken hacksaw blade in a reciprocating saw... quick, no sparks, easy You can even cut reasonable curves due to relatively narrow blade depth
Definitely a cool idea, to build and film it, but... My God did you let some parts go for WAY. TOO. LONG..... Please, for any other videos in the future, Edit some up the more tedious and boring parts out. I don't need to watch you use the grinder for 10 minutes doing the same cut maybe, 10 15 seconds and then move on to something else I fast forwarded a lot of your video because of that. I'm interested I want to see but you need to edit that stuff out If you want to keep people coming back to your channel that is. Take care hopefully you took this as constructive criticism. 👍
….aside of bein’ always right on diagnosed motorbike that has an issue base on listenin’ first before ever dismantle the parts…brade amad also quit handy with his hand by buildin’ a d.i.y wet water blastin’ machine from ground up…kudos abam amad… …p/s…that wet water blastin’ machine would be an eye catchin’ if its has m-power colors…huhuhu
MAKE SURE THERE IS NOTHING FLAMMABLE IN THE BARREL.not even a little bit,the fumes will explode.there are couple videos here on youtube where that exact thing happens
@@AhmadKhan66 kena pattern kan utk harta intelek Bang... Sy pu x terpikir Tong Drum boleh modified bt benda ni..... Modified demi Safety Semua Staff 👍🏻👍🏻👍🏻👍🏻👍🏻 respect..
Salam abg mohon pencerahan, wet blasting ni ada guna air compressor sama mcm sand blasting ke bang? Atau dia guna water pump sahaja untuk lajukan tembakan air. Maaf bang mohon pencerahan. 😢
Why are you using the grinder backwards, are you trying to hurt yourself? Sparks should be flying at you. That means the grinder is trying to run away from you, not trying to attack you.
How is he using it backwards? He could have been shoot the sparks away from flammable materials or something. right way to use a grinder is the way that gets the job done, and the first thing you do is take the gard off and throw it in the trash
There are times when one must use a grinder in an unorthodox situation. However, your comment suggests you have logged minimal grinder hrs. If one is trying to push or drag a cut opposite of the tools intended operation, the kickback or tool failure is almost certain! Cutting wheels are weapons when they come apart. Machines don't care about your meaty digits, your feelings, or your life!! I've seen lots of bad things happen to guys with grinders/machines/tools who knew more than engineers who designed them! But hey, you do you and may your fingers grow back faster than most! God bless.
@chrisnak76 yes I have thousands of hrs with all forms of grinders n hand tool ,n learned the hard way a couple of times n agree with you absolutely, knowledge n respect for the machine/tools you use
Everything u cut you cover everything with grinding debree. Bad for everything. Could short out your welder. Looks like a RealGear140 multi purpose mig.
I don’t care what country you’re from or language you speak, making stuff is universal!!! Way to go 🤘🏻🤘🏻🤘🏻🤘🏻🤘🏻🤘🏻🤘🏻🤘🏻🤘🏻🤘🏻
Thnaks for watching...
I have 2 suggestions. Put a submersible water heater in the basin so you have hot water and add a rust inhibitor to the water, so parts don't rust right away after cleaning.
Thanks for the tips! We had the rust inhibitor put inside the besen already after the vid. Maybe hot water would be an option! Thank you again for the tip!
Put sand in with the water
@@Swanlord05 sand will damage bearings and mating surfaces! only thing i would add is maybe some cheap detergent to help break down oil and grease!😀
@@AhmadKhan66I was also spray the inside glass with a water repellent to keep good visibility in there awesome skills by the way
Yeppirs, excellent work there. An abrasive option for all surfaces would be Baking Soda. Works very well and bounces off of rubber and actually cleans bearing surfaces. To test the amount of soda to add, i would suggest using an old wheel bearing (needle bearing style) with micrometer measurements before and after. Then test a ball bearing style the same way to adjust the water-to-soda ratio.
We melted 6 K-Cup microscreen filters together end-to-end and used as inline return water filter to keep debris from going back into the pump.
Nice job my friend -- good luck!
Wow jarang2 tgk sifu diy barang2 mcm ni😅
Mantap ahh bang mad,buat sendiri je mesin ni,diy tak payah abis beribu nak beli mesin fungsi serupa,pakai tong dram je,gunakan 100% kreativiti sendiri.❤❤👍
I clicked thumbs up on this video because you have the blade protector installed on your angle grinder. That's how you know you're dealing with professionals. 👍
Exactly, the ammount i see without them is insane!
Yet forgot to take the plugs out of the drum before cutting at least it didn't go boom
Well holding it the wrong way round is definitely NOT very professional and extremely dangerous, even with a guard at 6:07
ni mamat ada gaya suka DIY untuk kegunaan kedai... bagus dan kreatif... elok lepas ni buat Custom Modification Motosikal... ala² American Chooper.... kan bagus gitew....
Wouldn’t it be better with a pressure washer as the pump it seems pretty weak
Use a dirty water pump because it wont be damaged by the blasting media in the water. The compressed air is what gives it the power but might need more air flow?
Terbaik bang buat wet blasting sendiri.....rasa mcm nk Diy sendiri jgk untuk bengkel kereta saya jgk...untuk kerja² membersihkn head dan lain² komponen...nice idea bang🙏🏻👍🏻
Salam... Mantap pak abu... Lps ni, Abg Mat jd toke mesin portable wet blasting plk...😅😅😅
Hahah tak arr.. buat sebijik untuk kedai okaylah.. nak niaga todak kot...
@@AhmadKhan66 🤣🤣🤣🤣
Kemas hasil kerja bang..Bang buh rain water repellent kereta yg murah bang kat cermin..biar air x melekat kat cermin..baru clear mata memandang time basuh barang..
Thanks... noted... nanti saya sapu...
@@AhmadKhan66Patutlah upah cuci aje sampai 1K...Kalau cuci pakai manual sahaja rase mcm nk baling scraper ke dinding😂...Kalau saya yg cuci kaedah manual pun rase fedup jugak...Hahaha
Kadang² enn, tngok abg Ahmad buat DIY tools mcm ni pon mantap jugak...😁
Abang buat lah satu saya beli
Haah lepas tgok video ni smpai habis sy setuju
You Thai / Asian bros have engineering tied down. Ingenious and imaginative as skill ❤ all love these vids and flip flop racing
padu bang mad belanjaaaa content diy kali nii.. mantabbbbbpp
Nice idea to use a barrel for this project 😀👍.
It helps a lot if you use dishes soap or industrial cleaner soap.
This will help dissolve the oil residue 👍
I would use a different type of pump... a impeller pump like that is high volume / low pressure and if you reduce the pipes like in the video volume and pressure go down because of the impeller.
Nice job! 👍
Needs a filter to filter the dirty water. Just run it in the hose to the gun. Get one you can change.
Perghh gile respect bang. Dgn hasil keje cara keje kemas. Clean. Lpsni s1k mmg sy hntr sni bang.
Terinspirasi betul ni. 👍👍👍
terbaik bang. sharing diy yg semua peminat boleh buat sendiri kt rumah. guna brg2 yg boleh cari sendiri...custom.
Real techboss. Brilliant invention. Excellent guidelines for newbies. ❤ 👍
Did you use any glass beads?
Brilliant work brother maybe a silicone or waterproof coating for inside acrylic sheet help to stop water bubbles
Are you just using straight water to blast those parts. Need a filter in your sump pick up.. Not bad. That's a cheap way to make a high pressure washer. What kind of spray nozzle are you using?
Using a water blasting jet nozzle...
bos,wet blaster dgn sand blaster ada perbezaan tak.tp apa apa pun padu sifu diy
A drill and jigsaw would have been cleaner and alot less flammable.
Watching this brought to mind Albert Einstein's maxi - make it as simple as possible, & no simpler.
This was very quick & easy to build -if you know how - & cheap. & effective. What more could you ask for?
Try wiping the view-port with dishwashing liquid to avoid misting.
Or rub it with a cut potato.
Impressive :) , Tried building these multiple times and its like my sandblasters works 50% of the time rest of the time doesn't even following basically same builds as others.
They are really handy to have
If you have a pressure washer you can get an adapter to use with it to use it for sand blasting. Only thing is you have to remember to keep the sand sucking hose above the nozzle so water doesn't leak back n get the sand wet n gumm up.google. pressure water adapter to sand blaster adapter.
Super quick easy method of cutting straight lines in drums, 1 quick drill hole as starting point, then broken hacksaw blade in a reciprocating saw... quick, no sparks, easy
You can even cut reasonable curves due to relatively narrow blade depth
Definitely a cool idea, to build and film it, but... My God did you let some parts go for WAY. TOO. LONG..... Please, for any other videos in the future, Edit some up the more tedious and boring parts out. I don't need to watch you use the grinder for 10 minutes doing the same cut maybe, 10 15 seconds and then move on to something else I fast forwarded a lot of your video because of that. I'm interested I want to see but you need to edit that stuff out If you want to keep people coming back to your channel that is.
Take care hopefully you took this as constructive criticism. 👍
Thanks you... sure will take that into acc...
Padu baq ang..👍👍👍👍... Benda boleh DIY....
Mantap Pak Abu...kena resigter pattern ni. Nanti orang curi idea
Mantoppp... semua boleh buat bang... ini brg simple ja...
Creative permudah kerja Mantap...😊
Asskum..bro mat Tangan berseni..serba blh...Termantop 🎉 🎉🎉kemas TonG blass water jack...
….aside of bein’ always right on diagnosed motorbike that has an issue base on listenin’ first before ever dismantle the parts…brade amad also quit handy with his hand by buildin’ a d.i.y wet water blastin’ machine from ground up…kudos abam amad…
…p/s…that wet water blastin’ machine would be an eye catchin’ if its has m-power colors…huhuhu
Great video, excellent result form a nice bit of kit. Job well done mate, thanks for sharing. Cheers
Steady pak Abu..betoi2 creative nie..nk tempah 1 boleh kott😂
Cermin tu buat coating yang slalu buat kat cermin kreta bang, tak air tu melekat kat situ, lagi clear but kerja 🤜🤛
thanks... next pemasangan cermin kita buat
Mind sharing the type of pump and nozzle you used? THX!
I have something similar made from a pressure washer with a sand hopper..
Awesome.. Love from Palestine❤
You have a done an excellent job friend !👍
Thanks...
Nice and cheep way to go I like it my friend
Thanks
Moga dipermudakan segala urusan abg sekeluarga
Excelente ideia!
Is that using a standard sand blasting gun except water where the abrasive would go in ?
faster and cheaper is one can of oven cleaner.
MAKE SURE THERE IS NOTHING FLAMMABLE IN THE BARREL.not even a little bit,the fumes will explode.there are couple videos here on youtube where that exact thing happens
Awesome lh Ahmad khan. Abang sayang kamu. Aku abang ke ko yang abang. 😂
Hahahha mana jer bang.
Mntap bang. Brpa kos semua buat mcm ni
You need a new disc on that grinder!
you can add an anti rain/fog film that usually installed in motorcycle helmets to still have clear vision despite of water everywhere
Hasil kerja anak malaysia terbaik🎉🎉🎉🎉
What blaster nozzle did u use.
Dh mcm sciencetis NASA😮....
TerBaik Boss
Safety First👍🏻✌🏻
Hehehe kita cuba bang
@@AhmadKhan66 kena pattern kan utk harta intelek Bang... Sy pu x terpikir Tong Drum boleh modified bt benda ni..... Modified demi Safety Semua Staff 👍🏻👍🏻👍🏻👍🏻👍🏻 respect..
Salam abg mohon pencerahan, wet blasting ni ada guna air compressor sama mcm sand blasting ke bang? Atau dia guna water pump sahaja untuk lajukan tembakan air.
Maaf bang mohon pencerahan. 😢
Wouldnt be caught dead grinding next to all those bikes.
Bro khan..pakailah safety shoes.tq
Dia pakai air shj atau ada campur chemical? Mintak tunjuk ajar 😊
Assalamualaikum bang..paduu mantoppp👍✌️
🇸🇦Sollu Alan Nabi🇸🇦
Wasalam... amin..
What are you using as a pistol spray gun?
our abam Amat deserve more viewer and sabsescaraper
Pressure washed those bearings back to standard tolerances, paint it blue and call it new.
wow...kali ni content utk pasaran export international ... 😅
Abg ..abg mmg x pernah salah erk... Pelik... Asyik terpaling betul je... 😂
Lain macam kali ni punya video
I was wondering where you're going to throw that dirty water of carbs......
What are the specs on that pump?
Assalam..mintak halal ilmunye bang..nk try wt jgk ni..
Personally, I prefer one of those "die-grinder" style cutoff tools, especially for small circle cuts. Just sayin'...
Patut moto aku lambat,dia diy misin blasting 😂😂😂 hahhaha gurau2 je bang,
Buat tempat tong panggang ayam bakaq lepas ni.. Baru mables sempena nk sambut ramadhan 😂
Mantap Pak Abu 🎉🎉🎉
Mantoppppp...
Why didn't you use a pressure washer. It's already built and would the same job quicker. Plus you wouldn't waste a perfectly good 55 gal drum.
Blast cabinet contains the mess, keeps operator cleaner.
Wetblasting ni kene ade angin compressor jgk ke bang?
mantap abg ahmad buat diy ini dikatakan mantap pak abu..👍👍👍
tp hati2 lah masa nk grinder tu.cuci kaw2 drum tu.saki baki mnyak chemical pnya la.lubrican ok ja cuci skit2
abg mat msti kecik2 dulu suka makan kismis...
Just looks like a homade sand blasting cabinet but the hand holes are waaay too far spaced.
Nice work 👌
Mantap pak abu....dah mendonia channel nie hahaha😂😂😂😂👍👍👍👍
Good Job ! What ya have there is a Pneumatic Pressure Washer …..
Needed to pull bearings out of case b4 cleaning and a pressure washer would have been better choice
Baik pakai water jet je , kn sama function dia , apa2 pun mantul kerja kemas mantapan
The only thing I would done differently is use a stainless steel drum.
Targeting international audience. Mantap
Well done bang mad! Mantap pak abu.. Miow2 ciaw2 Kami syg bang mad🤣
Why are you using the grinder backwards, are you trying to hurt yourself? Sparks should be flying at you. That means the grinder is trying to run away from you, not trying to attack you.
That for reminding.. sometimes during built up does forget...
How is he using it backwards? He could have been shoot the sparks away from flammable materials or something. right way to use a grinder is the way that gets the job done, and the first thing you do is take the gard off and throw it in the trash
There are times when one must use a grinder in an unorthodox situation. However, your comment suggests you have logged minimal grinder hrs. If one is trying to push or drag a cut opposite of the tools intended operation, the kickback or tool failure is almost certain! Cutting wheels are weapons when they come apart. Machines don't care about your meaty digits, your feelings, or your life!! I've seen lots of bad things happen to guys with grinders/machines/tools who knew more than engineers who designed them! But hey, you do you and may your fingers grow back faster than most! God bless.
@chrisnak76 yes I have thousands of hrs with all forms of grinders n hand tool ,n learned the hard way a couple of times n agree with you absolutely, knowledge n respect for the machine/tools you use
Terbaik bang..mmg seorang yg kreatif 👍👍👍👍
ni kmpem viewer dr russia mai tgk. caya la👍👍👍
Oil drum and sparks, mmmm, BOOM
Pehhhh… Bukan main bersih lg wehh…
Persoalannya ialah Abg Mad ni mmg multi-skill ke?? 🫡
hahahaha... kita buat jer... jadi tak jadi blakang kira...
Everything u cut you cover everything with grinding debree. Bad for everything. Could short out your welder. Looks like a RealGear140 multi purpose mig.
Lol, you think they cover every machine in a welding shop when someone starts a grinder ?
Terbaik laa bang.. mcm Mac Guiver laa.
Pintu tu abg kna guna plate yg besar sikit dari lubang pintu yg kt barrel tu bang..watertight sikit.
saya tambah palstic sheet blakang tu, besar dari pintu.. so air dah tak kuar setel...
Mantap bos..nampk pakai baju alang motor. Kwn sekampung aku..
How much psi did you use bro?
😊😊😊😊😊 terbaiklah
Thanks...
I was in my mid 50’s when I started watching this video, I’m now 96 and writing this comment from my nursing home 🧐
This channel’s oldest video is 11-years old.
Will a plastic drum would work?
I believe it can...
bang....😂😂😂 sejibik mcm video negara seberang
heheheh... skali skala try buat
Kontol
Mantop pak abu. Serba boleh