I literally had this problem today. My wife called me in a panic stuck in the road in traffic. I instructed her to shut off and put in gear and try to get the car off the roadway. She did and she waited for me to go pick her up. I searched out this issue and got to your video. Did exactly what you instructed and it worked. The valve wasn't all the way opening. Cleaned it with the cleaner (not exactly the same can but one that was a good substitute) worked like a charm. Thank you. Thank you. Got better acceleration and just runs better just from that. Thanks again amigo!!
You genius! We took my mom's car to a mechanic that told us it was going to be the spark plugs and coils and wanted us to spend 1500 to replace the parts. I saw your video and gave it a shot. It's running better than before now so thank you for making this video.
What the guy above said, never go to that mechanic. 4 ignition coils and spark plugs from Toyota would cost about 450. The job would take him 20 minutes. 1500 usd for that is ridiculous
Wow this was a super simple procedure and worked great on my 2011 Carolla with 186k miles! The engine seems to run much smoother and idles at a higher RPM (around 1000). Thank you 👍🏻
Great job pm explaining the detachment of every connector. I've been a boiler operator/mechanic, a rocket surgeon, and now I'm on my last gig before I retire doing logistics for a chip maker. I know how to follow instructions. But far too many of these videos leave out or gloss over a critical step. I don't know why- if you doing a How-to, it completeness that matters - not the background music or cool intro. I'm just watching this for like the third or fourth time, right before I pull that assembly so I don't end up with a mystery connector, or spend an extra half hous because I disconnected the wrong side of something, and irmt just struck me how well you covered the one indispensable sequence clearly and succinctly Kudos! Update Wouldn't you know it, just as I got to thr last clamp, the rain ppen up and the wind kicked up. Ducked.back in the house to warm up and dry out.
Man I watched so many stupid videos about messing with the wiring harness and vaccum lines to resolve this issue, this actually solved my cars issue and saved me so much headache and money 🎉
THANK YOU! A friend of mine *just* got his Camery back from an (albeit unrelated) expensive mechanic visit and a day later it started to stall when idling. As a result, he's already a couple grand in the hole and this was not what he needed to deal with a day later so I looked into it, found your video, and within 15 minutes his car's running great again!
Broooooo you are a lifesaver lol. Swapped my battery didn't know about the idle reset until I googled why my idle sucks after changing my battery and bam got it solved thanks to you in 5min. FJ runs like a champ now
Nice video! I had to show this to the mechanic!!! Cause they didn’t know what To do and couldn’t know why my car was shaking and shutting off, I just needed to get this cleaned.. thank you!!!
Thank you I just did this ten minutes ago… my idle is above 1500.. I think it’s kinda high but maybe because it’s still cold.. regardless before my idle was 500 and my car would shut off randomly on idle .. thanks so much I liked and subscribed
Good video, if you have no one to help you, just disconnect the battery, and do the rest on your own, no check engine light no codes, no harm done as long as the battery is disconnected, i did that on my, camry, my corolla, with no problems at all, the computer will reset and rpm will get back to normal after a couple of hours of driving.
Thank you for this video . I have a 2011 Camry that was doing this . I changed the MAF and nothing . I followed your steps I. This video and it fixed the car . Thank you again
Same here, I changed the MAF, PCV valve, Purge solenoid valve on my 2007 Camry SE V6 and nothing, as soon as I did this and cleaned the Throttle body the car feels like new again! Thank You so much for this video.
Hey RB, When doing this do you have to be careful not to move the throttle plate with your fingers or can you move the plate with fingers to clean throttle body where plate touches/meets?
Nice explanation. I have a problem with 2017 camry. It used to vibrate (as if driving on rumbler) when the rpm is around 1500. It runs smooth above and below that rpm. The mechanic diagnosed and replaced the front axle but it only made the situation worse. It occurs more frequently now and intensity of vibration is increased. Do you have any suggestions?
Thanks. I had the low rpm issue(down to 500 rmp) especially when turning on the ac. after the cleaning it the low idle is gone and engine is smooth 800- 900 rpm.
Hi there, I have a 2010 Camry which is stalling when I put it on park or neutral. This only started happening after I changed my battery. Do you know what might be the issue and how to fix it ?
Well u lost idle memory when u took out the battery check my how to replace batttery videos anyways. Turn everything off wiper lights radio all accessories off and start the car and let it idle for 20 minutes let me know if it builds idle. If it dosent then I’ll give u more instructions
Hello! Please help, i performed the throttle body clean as you instructedon my Camry 2008, but now the car jerks when idle, especially when the car is in Drive and i have the brake pedal pressed. I've trid idle relearn procedure but no luck, any suggestions? I notice the RPM gauge is jittery and spikes up slightly. Car drives fine, but that jerking & shaking when idle is not normal, please help.
Going to do this tomorrow; my 2010 Camry just started stalling when I stop. I changed the plugs and air filter- both needed to be replaced, but it’s still stalling. Thanks
@@RBTheMechanic since doing this, the car hasn’t stalled once and the gas pedal is much smoother. I cleaned the throttle body on my wife’s Toyota Matrix then cleared the check engine light (was for O2 sensor). We’ve drove it 600 kilometres (highway and city combined driving) and the light is still off. 2 cars fixed with one simple process. 🙂
@RB the mechanic. I notice a misfire at 1300 rpm with engine cold or hot. It idles good and smooth and drives good. Sometimes intermittently I’ll come to a stop light and the rpm’s will drop from 900 to 600 and returns to 900 as if it was almost going to stall. Any advice?
Great information brother… I will try this on my Toyota 2014 … my car feels like it wants to shut off wile driving like I can see the RPMS drop . Any good ideas?
That might be somthing else or transmission related but this service is good to do it will keep the preformance of throttle response better so go for it and it dose send siginal to transmission module to shift accordingly so go for it!!
I have 2010 toyota corolla. similar throttle body top right cornar there is a screw hidden in a glue type material. can you please tell me, what is the function of that. and how it help in adjusting a specific parameter? I have observed that changing the position of that screw make throttal pedal to respond differently and effect the drivability . I have an issue of poor idling. throttle body is cleaned. every possibility has been checked but could not fix the issue.
@@RBTheMechanic The mechanic has already messed with it. Now I need to bring that screw on orignal position, or alteast to adjust it on properly. any idea how it functions?
@@RBTheMechanic sorry i did not understand what do you mean by load on flap? one person told me, that in toyota corolla electronic throttle body this screw is to raise or lower the idle RPM, but in my case I have observed that rotating clockwise it reduces the RPM but at certain point further clockwise rotation of screw again start to increase the Idle RPM, still confused how to check and verify the optimum position of screw and how it perforn its function? also trying to search service manual of electronic throttle body on internet but could not find.
i just did what you do... now the engine idle at 1600rpm, what should i do? i saw your reply about idle re learn. how do i do that? is there a video on that?
You have to do idle relearn. Make sure engine is at operating temperature. I check engine reset the light if there’s any codes for higher rpm anything else repair it. Here’s a video ruclips.net/video/sCsBqeZctzE/видео.htmlsi=HEoeGk03DPU0IM9V
When the engine is warm and if I let the car sit for 10 minutes and restart the car, the idle drops to 500 rpm for 1-2 seconds, runs rough, and then the idle smooths out? Any idea what could be causing this issue? I cleaned the MAF sensor, throttle body, replaced the plugs, coils, ECT sensor and crankshaft position sensor, and it still does this. There is no CEL, crank time is short and no noticeable drop in gas mileage.
Hey. Thank you for the video. Today my 2013 Camry SE was running and while it was running I unplugged the AMS and the car shut off. I put it plugged the MAS back and turned the car on it turned on but the engine light turned on. How to reset the engine light off. Any help would be appreciated. Thank you.
Hi there! My Toyota Camry 2014 has 75,475 miles on it and it barley started doing this. I noticed it doing it after I’ve been driving for a little and then stop at a red light or stop sign. It does it for a quick maybe 2 to 5 seconds where I see the needle want to go down and the car shakes and wants to turn off so I let go of the brake…..then it doesn’t do it anymore. Also, there’s no check engine light or anything. Can this be the problem?
Yup it would get nice and hot then it would start to do cuz computer knows to lower the idle speed once’s it’s hot but then it can’t maintane the idle rpm speed so go for it do this service it will only be for the hood of vehicle
Thanks so much for the details description of the process. I got a new battery and new alternator but problem didn’t get fix. After this process, no more crazy idle and most important the engine doesn’t shut down at the red light. 🫡🙏🏼
@RBTheMechanic I checked. Surprisingly it went away after 4 startups. Lol. Turns out I was reseting the system. But I did the checkup anyway and they say I have to replace the mass air flow sensor according to the code. Thank you very much 😊
Excellent walkthrough, thanks! With the key on ACC, when you press the gas pedal, would that cause the computer to try to add gas as well to match the throttle body position? Can you leave the gas all the way down as long as you want with no issues?
My car idles poorly on drive and reverse gear with my foot on brakes, I feel vibration on my steery and dashboard while idling. It idles at 600rpm to 550rpm is this normal, with so much vibration n gets worse when I turn the ac on still on drive or reverse gear but reduces a bit when I put my car on park gear n vibration disappears when my car is moving n comes back when I come to a stoplight. I think, ama give this a try and see if it solves d issue.
@@unisuit i think he may have forced it or somthing only u urself would avoid all pro cautious anyways disconnecting battery will allow it to loose the idle memory then it will be low rpm u will need to relearn the idle it may try to stall on stop sign on red lights
Fixed. Throttle relearn did not work. Battery disconnect, then throttle relearn resolved issue. Thank you for your time and knowledge. You saved us a lot of money.
Would this work for random reving up of rpm when driving? I noticed sometimes just driving a constant speed or sometimes when accelerating, it will rev up rpm then go down to what it normally increase to
I have the same camry 2013. It doesn't turn off on the stop light but sometimes it feels like choking when I'm gaining speed and rpms are always low, about 1700-1800 no matter the speed I drive. Do you think it could be the same issue with the throttle body?
@RB The Mechanic the idle is around 700. 1700 -1800 is when I'm driving and that's when it feels like the car is choking so I need to accelerate so the car start driving better
Do you happen to know what the problem can be when you depress the gas pedal with the key on acc the throttle flap opens really slow? At times It opens instantly then sometimes it opens slow?
There’s no problem there these care are designed to only open depending on speed of the car for safety reasons but I can trying cleaning it might have small jam or bad throttle
Would something like a bad throttle or dirty throttle throw a mass air flow sensor code? That’s what happen in my case I replace the mass air flow but the code never went off. I come across your video and I clean the throttle body put everything back together cut the car on check engine light was on drove around the block cut the car off and back on the light went out, next day it come back on. Any idea as why it’s doing that? Thanks
@@danieldo6254 I’m here because i have that same exact issue right now. Gonna clean the throttle body out first and if it still stalls then i might just replace the sensor as well.
@@NpausAsHawj hey I end up replacing the fuel pump and got the oem sensor from Toyota and everything worked fine no check engine light no hesitation good to go hope that helps.
This can be the issue or engine mount. Try to notice where ur rpm is when ur idling and it’s vibrating if it below 700 then u can say this is the issue
I have toyota camry 2004 (manual) When i run the car without airconditon the rpm is not drop but when i turn on the Aircondition car feel little bit shake then car when running about avobe 30+ speed the rpm is good but when car get reduced speed car shaking and when gear in neutral engine get stop plz tell me about the problem🙏🙏
My 2015 camry le idles at 800 rmps when it's on park but when I put on drive or reverse it drops to 500 or 600 rpms and it shakes and the has turned off when I'm at a stop sign or red light.
I literally had this problem today. My wife called me in a panic stuck in the road in traffic. I instructed her to shut off and put in gear and try to get the car off the roadway. She did and she waited for me to go pick her up. I searched out this issue and got to your video. Did exactly what you instructed and it worked. The valve wasn't all the way opening. Cleaned it with the cleaner (not exactly the same can but one that was a good substitute) worked like a charm. Thank you. Thank you. Got better acceleration and just runs better just from that. Thanks again amigo!!
Nice good job!!!
You genius! We took my mom's car to a mechanic that told us it was going to be the spark plugs and coils and wanted us to spend 1500 to replace the parts. I saw your video and gave it a shot. It's running better than before now so thank you for making this video.
Nice good job
Never go back to that mechanic
What the guy above said, never go to that mechanic. 4 ignition coils and spark plugs from Toyota would cost about 450. The job would take him 20 minutes. 1500 usd for that is ridiculous
Thank you for this man! My Camry used to want to stall in stop lights and now it idles pretty comfortably without vibration.
Nice job!!! Yup this is good service!!!
Wow this was a super simple procedure and worked great on my 2011 Carolla with 186k miles! The engine seems to run much smoother and idles at a higher RPM (around 1000). Thank you 👍🏻
Nice good job!!
Did you car die after couple sounds turning it on? I’m having this issue now
@@Mopar5.7_Ant didn’t understand what u mean by couple of sounds
@@Mopar5.7_Ant no it runs great.. it was a hard start the first time right after but it smoothed out quickly and runs like brand new
M Camry 2001 had this issue too. Cost was $115 for a cleaning. Thanks for the video. It helps me understand what the mechanic did.
Yeah that one is diffrent it has idle sensors but clean the throttle helps also
I have 2002 camry 3.0lt sometimes idle goes way down try to shut down
What do you think about that sometimes running perfect some times on stop sign feels.like misfire amd going to stall
Great job pm explaining the detachment of every connector.
I've been a boiler operator/mechanic, a rocket surgeon, and now I'm on my last gig before I retire doing logistics for a chip maker. I know how to follow instructions.
But far too many of these videos leave out or gloss over a critical step.
I don't know why- if you doing a How-to, it completeness that matters - not the background music or cool intro.
I'm just watching this for like the third or fourth time, right before I pull that assembly so I don't end up with a mystery connector, or spend an extra half hous because I disconnected the wrong side of something, and irmt just struck me how well you covered the one indispensable sequence clearly and succinctly
Kudos!
Update
Wouldn't you know it, just as I got to thr last clamp, the rain ppen up and the wind kicked up.
Ducked.back in the house to warm up and dry out.
Thank u
Man I watched so many stupid videos about messing with the wiring harness and vaccum lines to resolve this issue, this actually solved my cars issue and saved me so much headache and money 🎉
2002 Camry V6 le
Oh nice glad u found my video !!! Do this every 30k miles
THANK YOU! A friend of mine *just* got his Camery back from an (albeit unrelated) expensive mechanic visit and a day later it started to stall when idling. As a result, he's already a couple grand in the hole and this was not what he needed to deal with a day later so I looked into it, found your video, and within 15 minutes his car's running great again!
Nice good job!!! U should go complain to the work shop
You saved my life I don't know how to thank you enough. God bless you!
You're welcome! I’m glad this video helped u!!!
Broooooo you are a lifesaver lol. Swapped my battery didn't know about the idle reset until I googled why my idle sucks after changing my battery and bam got it solved thanks to you in 5min. FJ runs like a champ now
Oh nice job bro!!! Yup I learned this years back I was hell a confused I didn’t have utube back then but eventually made a Channel
@@RBTheMechanicdamn it seem like your the man fr 😂 since way back
@@FuckYouPayMe448 thanks
Nice video! I had to show this to the mechanic!!! Cause they didn’t know what To do and couldn’t know why my car was shaking and shutting off, I just needed to get this cleaned.. thank you!!!
Nice good job nailing this video to them
Thank you for this video. My hubby bought ignition coils & spark plugs & it didn’t help the stalling so we’ll try this next.
Oh ok yes this is good for low idle
What did it end up being? Bad alternator?
Thanks for the video man. Saved me tons of time and money. Late night fix so I can get to work tomorrow 🤙🏽
Nice good job!!!
Thanks for the video. It was helpful for me.
That hose clamp was not easy to get to😄.
It’s running better now, no stalling.
Good job!! Easy fix car runs like new!!
Thank you I just did this ten minutes ago… my idle is above 1500.. I think it’s kinda high but maybe because it’s still cold.. regardless before my idle was 500 and my car would shut off randomly on idle .. thanks so much I liked and subscribed
Do idle relearn it will become stable at 800 or drive around with ac light and all accessories off it will do relearn by it self
How long do you need to drive car for idle relearn?@@RBTheMechanic
@@spiderchata1 19-15 minutes
Thank you, sir! My 2011 Toyota Camry is running and not stalling anymore.
Welcome!! Good job !!
Good video, if you have no one to help you, just disconnect the battery, and do the rest on your own, no check engine light no codes, no harm done as long as the battery is disconnected, i did that on my, camry, my corolla, with no problems at all, the computer will reset and rpm will get back to normal after a couple of hours of driving.
I don’t like to loose idle unless it’s most necessary
Thank you for this video . I have a 2011 Camry that was doing this . I changed the MAF and nothing . I followed your steps I. This video and it fixed the car . Thank you again
Nice job!!!
Same here, I changed the MAF, PCV valve, Purge solenoid valve on my 2007 Camry SE V6 and nothing, as soon as I did this and cleaned the Throttle body the car feels like new again! Thank You so much for this video.
Great how to. I like it bc you go straight to the point. Is it harmful to the tb if i spray into the flappy thing?
No but try rag
Hey RB,
When doing this do you have to be careful not to move the throttle plate with your fingers or can you move the plate with fingers to clean throttle body where plate touches/meets?
I have done it with moving the throttle carefully with fingers
Nice explanation. I have a problem with 2017 camry. It used to vibrate (as if driving on rumbler) when the rpm is around 1500. It runs smooth above and below that rpm. The mechanic diagnosed and replaced the front axle but it only made the situation worse. It occurs more frequently now and intensity of vibration is increased. Do you have any suggestions?
Not sure what I can recomend u without test dirivinf how ever I would replace that axle with better axle before anything
can you just place a brick or something heavy on the accelerator while doing the entire cleaning process (instead of having a second person)?
Yeah I use stick against the seat that works for me as long as it holds and is solid
I used a stick too
Thank you sir. Had to disconnect battery earlier. It was stalling bad. This fixed it
Cool
Thanks. I had the low rpm issue(down to 500 rmp) especially when turning on the ac. after the cleaning it the low idle is gone and engine is smooth 800- 900 rpm.
Nice job
Hi 👋🏿 thank you for posting this is an extremely helpful video. Do these cars have a idle air control valve, or just the throttle body?
Throttle body is the IAC since it electrical it dose job for both
I just curios why don't take out the throttle body out then clean up everything ?
Welll no need to u will damage the throttle body also once u loose all power ur idle memory will be lost
Use a toothbrush instead of a rag. Makes it a lot easier and cleans those hard to get to spots
But that don’t bring out the carbon
Do you got the car running or just got the key turned forward
Not running just on accessories
You explained it perfect. Great video. It worked for me. You saved me a lot of money Thanks a lot.
Nice job!!! Good fix this will make car run much much better!!! I’m happy u did this
It hasn't stall since I did it...thanks💯
Nice good job!!!
Thanks, I think a have a bad pcv that is causing this problem, no smoke but I burn a quart every 2 weeks.
Try pcv and try changing type of oil maybe castrol
Hi there,
I have a 2010 Camry which is stalling when I put it on park or neutral. This only started happening after I changed my battery. Do you know what might be the issue and how to fix it ?
Well u lost idle memory when u took out the battery check my how to replace batttery videos anyways. Turn everything off wiper lights radio all accessories off and start the car and let it idle for 20 minutes let me know if it builds idle. If it dosent then I’ll give u more instructions
@@RBTheMechanic tried it, it didn’t work.
@@FaisalElGhaffir try idle relearn ruclips.net/video/sCsBqeZctzE/видео.htmlsi=dnBBtBz42UpFwFRH
After I cleaned mine, check engine is now on. Is that normal?
No reset it
@@RBTheMechanic thanks. I cleaned it last night. If it continues stalling, any adía what else could be?
Does it stall on idle only or high speed
Hello! Please help, i performed the throttle body clean as you instructedon my Camry 2008, but now the car jerks when idle, especially when the car is in Drive and i have the brake pedal pressed. I've trid idle relearn procedure but no luck, any suggestions? I notice the RPM gauge is jittery and spikes up slightly. Car drives fine, but that jerking & shaking when idle is not normal, please help.
Do idle relearn
Where can i buy the y tool screwdriver from? Is that the correct name of the tool? Thx
Snap on or any other Autostore ebay amazon trim pad clip removal fork
Going to do this tomorrow; my 2010 Camry just started stalling when I stop. I changed the plugs and air filter- both needed to be replaced, but it’s still stalling. Thanks
Yup definitely good service to do!!!
@@RBTheMechanic since doing this, the car hasn’t stalled once and the gas pedal is much smoother.
I cleaned the throttle body on my wife’s Toyota Matrix then cleared the check engine light (was for O2 sensor). We’ve drove it 600 kilometres (highway and city combined driving) and the light is still off. 2 cars fixed with one simple process. 🙂
@@barry009 this is the best service u can do every 20k miles
Do these cars have an IAC valve or is it part of the throttle body?
Electrical throttle it’s both 2 in one
When l start my car up in the morning it revs 2000rpm than jolts to 1000rpm would this be the throttle?
@@danielmillard8134 colde start will do that I find that normal
I cleaned and changed the throttle body but it still stalls I don’t have check engine but still read the codes p1603,p1604,p1605, and p2109
Did u do idle relearn
@@RBTheMechanic yes I did
Hey can I use carb and choke cleaner?????
Yup but try to get ccatalytic cleaner Bette roption
@RB the mechanic. I notice a misfire at 1300 rpm with engine cold or hot. It idles good and smooth and drives good. Sometimes intermittently I’ll come to a stop light and the rpm’s will drop from 900 to 600 and returns to 900 as if it was almost going to stall. Any advice?
Start with this cleaning service
Check the timing. Make sure chain or belt is tight.
I cleaned and it’s still not working
Could I just change the throttle body sensor on it?
or do I have to replace the whole throttle body ?
If it needs replacing the whole throttle got to go did u disconnect battery before or after? What is ur RPM once car is nice and hot
Great information brother… I will try this on my Toyota 2014 … my car feels like it wants to shut off wile driving like I can see the RPMS drop . Any good ideas?
Yeah start from this usully when u at stop sign or red light it will do that cuz ur not pushing gas peddle
Thanks for the video my car works great now 👍🏽
No problem 👍 nice job!!
My vibe 2.4L gives a sluggish acceleration while on the slope.. could it be this?
That might be somthing else or transmission related but this service is good to do it will keep the preformance of throttle response better so go for it and it dose send siginal to transmission module to shift accordingly so go for it!!
Solved my rough idling issue! Thanks so much!
Great to hear!b nice job!!
I have 2010 toyota corolla. similar throttle body top right cornar there is a screw hidden in a glue type material.
can you please tell me, what is the function of that. and how it help in adjusting a specific parameter?
I have observed that changing the position of that screw make throttal pedal to respond differently and effect the drivability .
I have an issue of poor idling. throttle body is cleaned. every possibility has been checked but could not fix the issue.
Don’t mess with it it has function to adjust but don’t mess with it u need to clean it first
@@RBTheMechanic The mechanic has already messed with it. Now I need to bring that screw on orignal position, or alteast to adjust it on properly. any idea how it functions?
@@inamrehman8709 it’s load for the flap but it dosent do much I messed with it before but u don’t need to touch it
@@RBTheMechanic sorry i did not understand what do you mean by load on flap? one person told me, that in toyota corolla electronic throttle body this screw is to raise or lower the idle RPM, but in my case I have observed that rotating clockwise it reduces the RPM but at certain point further clockwise rotation of screw again start to increase the Idle RPM,
still confused how to check and verify the optimum position of screw and how it perforn its function?
also trying to search service manual of electronic throttle body on internet but could not find.
@@inamrehman8709 hard to explain but it just adjustment dosent do much on any preformance or stall fix just leave it alone
Thank you, easy to follow instructions. Very useful
👍
i just did what you do... now the engine idle at 1600rpm, what should i do? i saw your reply about idle re learn. how do i do that? is there a video on that?
You have to do idle relearn. Make sure engine is at operating temperature. I check engine reset the light if there’s any codes for higher rpm anything else repair it. Here’s a video ruclips.net/video/sCsBqeZctzE/видео.htmlsi=HEoeGk03DPU0IM9V
I did it works perfect ,just getting the check engine light now ,what can I do?
Did u scan for codes u shouldn’t have had that light if u did it correct but u can scan and reset
@@RBTheMechanic I took it for a test drive and I’m getting bad mpg .
@@okaycool1232 clean oxygen sensor and max sensor that might fix things up they control gas
@@RBTheMechanic Thank you will do!👏
My camry 2016 is vibrating in morning at signal stops, but its ok when warm
Why is it at light but not warm?
When the engine is warm and if I let the car sit for 10 minutes and restart the car, the idle drops to 500 rpm for 1-2 seconds, runs rough, and then the idle smooths out? Any idea what could be causing this issue? I cleaned the MAF sensor, throttle body, replaced the plugs, coils, ECT sensor and crankshaft position sensor, and it still does this. There is no CEL, crank time is short and no noticeable drop in gas mileage.
U might want to Re clean the throttle and do idle relearn
Change your fuel filter.
Hello dear I have Toyota Camry when I start engine shake please suggest me
Dose it shake once’s it warms up?
Thank youuuuuuu you helped fix my vehicle ❤❤❤❤❤❤😊😊😊😊😊😊
Good job
Hey. Thank you for the video.
Today my 2013 Camry SE was running and while it was running I unplugged the AMS and the car shut off. I put it plugged the MAS back and turned the car on it turned on but the engine light turned on. How to reset the engine light off.
Any help would be appreciated.
Thank you.
U have to reset it with scan tool
@@RBTheMechanic can autozone reset it?
Thank you.
I just did that and my cars check engine is on right now, also when i turn the car on the rpm is almost 2000, what would be the reason?
We’ll try the light u might have had the sensors disconnect when doing this it picked up on it
Hi there! My Toyota Camry 2014 has 75,475 miles on it and it barley started doing this. I noticed it doing it after I’ve been driving for a little and then stop at a red light or stop sign. It does it for a quick maybe 2 to 5 seconds where I see the needle want to go down and the car shakes and wants to turn off so I let go of the brake…..then it doesn’t do it anymore. Also, there’s no check engine light or anything. Can this be the problem?
Yup it would get nice and hot then it would start to do cuz computer knows to lower the idle speed once’s it’s hot but then it can’t maintane the idle rpm speed so go for it do this service it will only be for the hood of vehicle
@@RBTheMechanic Awesome 🙏 Thank you so much sir!
Hello, nice job, cuestion, a dirty throtle can gives a po172 code?
Don’t think so but possability yes but this code send me toward maf sensor or oxygen sensor upstream
Thanks, i will check that and also im going to check for air leaks, im learning watching videos, maybe i can fix my van, thank again
Were those microfiber towels or just the blue shop tissues?
Tissues will do
@@RBTheMechanic Thanks.
Hi sir I have 2010 Toyota Camry 2.5 l is jerk when I drive and then it goes.qwqy when I speed? Please I need your help
That could be transmission issues but before ruling that check and scan the car for codes also clean out this throttle
Can I use brake cleaner for this?
Yeah don’t spray on it through only on rag
@@RBTheMechanic Thank you👍🏼
Thanks so much for the details description of the process. I got a new battery and new alternator but problem didn’t get fix. After this process, no more crazy idle and most important the engine doesn’t shut down at the red light. 🫡🙏🏼
Welcome!!
Does this work on 07 Camry 4 cyl ?
Yup same thing
Can we clean it by removing totally ?
No u willl have idle stall issue from loss of memory
Hey, how much you think is a fair price to get this service done professionally?
This service $135 max
Well, I cleaned the throttle body by following the instructions in this video.
Now I ser a check engine light. Any ideas?
Car :2013 Toyota camry LE
Scan the car to see what the code is
@RBTheMechanic I checked. Surprisingly it went away after 4 startups. Lol. Turns out I was reseting the system. But I did the checkup anyway and they say I have to replace the mass air flow sensor according to the code. Thank you very much 😊
@@Dragunity69having this same issue rn
Good video. Very well explained and worked.
Welcome
Hello, thanks for the info. Now I have to find someone to do it. Where are you located?
I’m in north nj
What about v6 2grfe misfire goes away when start and stop but comes on after a load
Scan for codes and let me know what code u get
Excellent walkthrough, thanks! With the key on ACC, when you press the gas pedal, would that cause the computer to try to add gas as well to match the throttle body position? Can you leave the gas all the way down as long as you want with no issues?
No it will not add gas engine is off
Appreciate your videos, very helpful!!
Glad to hear it!
My car idles poorly on drive and reverse gear with my foot on brakes, I feel vibration on my steery and dashboard while idling. It idles at 600rpm to 550rpm is this normal, with so much vibration n gets worse when I turn the ac on still on drive or reverse gear but reduces a bit when I put my car on park gear n vibration disappears when my car is moving n comes back when I come to a stoplight. I think, ama give this a try and see if it solves d issue.
Do this cleaning service
What OBD scan tool do you recommend?
I use Snap-on but my next one will be the $2000 autel
Any reason why a 2019 Toyota Yaris would be doing this? At 20,000 miles
Could be dirty throttle this is very common issue on electrical throttle it’s sensitive it’s perfect time to clean every 20-30k miles
Awesome I’ll give it a check and clean! Anything else you recommend it could be if it’s not the throttle body
@@Ozone9300 air and cabin filters if u haven’t done those
Hi, may I have auto body shop address? I have same issue.
I’m in bayonne nj ru local
How much do you charge for a throttle body cleaning?
Depends on the car this one I use to charge about $90 now it’s more like $120 due to all shop expenses went up insurance and all
definitely appreciate this video ! everything worked just like you explained!
Nice job!!!
For me the car never stalls but my idle goes below 500 and vibrates sometimes when stopping and braking. Any suggestions.
Yup do throttle cleaning it’s low idle will be fixed
I cleaned my Subaru throttle in exactly the same way. Had to disconnect the battery to stabilize the rpms after that.
Oh ok
I'll try your method fo🎉r my daughter's 2010 Camry------later: runs like a charm❤
Ok update me how it goes
It worked !!! Thank you so much !
Welcome glad video helped you
Show the relearn process and cleaning MAF sensor. I had to do this recently 2011 Camry
I have few videos on that will make more down the road
Followed directions now the idle is 1600 (2k with AC on) Suggestions?
Do idle relearn… I never had issues did u disconnect battery or force the throttle
@@RBTheMechanic had some one turn key to on position and press the throttle to the floor. Sounds like I should disconnect battery for a hour to reset
@@unisuit i think he may have forced it or somthing only u urself would avoid all pro cautious anyways disconnecting battery will allow it to loose the idle memory then it will be low rpm u will need to relearn the idle it may try to stall on stop sign on red lights
Fixed. Throttle relearn did not work. Battery disconnect, then throttle relearn resolved issue. Thank you for your time and knowledge. You saved us a lot of money.
@@unisuit no problem always here to help!!
Here for lil bro’s Scion - buh yes MY Pontiac Grand Prix was KNOOOWWN for this super small detail 😫
Ok cool!!
Would this work for random reving up of rpm when driving? I noticed sometimes just driving a constant speed or sometimes when accelerating, it will rev up rpm then go down to what it normally increase to
No that’s more of weak transmission or slippage when it dose that it dosent have load from transmission it shifts to gear or delayed grab one the gear
@@RBTheMechanic Thanks for the quick reply. I'll chalk it up on transmission, I got a lot of miles on the car. Great video by the way.
What kind of cloth is that?
Regular rag would do nothing special
@@RBTheMechanic thank u💜
@@thaheartbreaker welcome
I have the same camry 2013. It doesn't turn off on the stop light but sometimes it feels like choking when I'm gaining speed and rpms are always low, about 1700-1800 no matter the speed I drive. Do you think it could be the same issue with the throttle body?
1700? Idle suppose to be around 700-800
@RB The Mechanic the idle is around 700. 1700 -1800 is when I'm driving and that's when it feels like the car is choking so I need to accelerate so the car start driving better
@@FranciscoCortez12 driving dosent have actual range so if ur idle is good the. U don’t need to worry however clean out ur throttle anyways
@@RBTheMechanic got it. Thank you!!
@@FranciscoCortez12 I have the exact same issue on a 2014 Camry 2.5L.
Thank you so much, God bless you alot😊
Welcome
How much is a new throttle body ? For this car ?
It’s like 500
Advice needed, I am having even lower idle after throttle body cleaning. What are the possible causes?
Did u do idle relearn usully it goes high not low possability bad throttle
What ended up being the issue?
@@ASMRBully this was it
I mistakenly removed the negative plug of the battery, to reset the engine light code, what can I do ? Please advice
No worrie. Try idle relearn finish up what ur doing and then idle relearn here is a video ruclips.net/video/sCsBqeZctzE/видео.htmlsi=tG1ibFrlNiyWRYUY
@@RBTheMechanic thank so much ! It work out for me
@@digen95140 welcome
Why is my car shutting off stalling hard once turned on? Toyota Camry 197xxx
It might need this service? Did u change battery or anything prior to the stall issue?
And remove the hoses very gently as they get hard with heat and can get damage if pulled hardly
Yup
Do you happen to know what the problem can be when you depress the gas pedal with the key on acc the throttle flap opens really slow? At times It opens instantly then sometimes it opens slow?
There’s no problem there these care are designed to only open depending on speed of the car for safety reasons but I can trying cleaning it might have small jam or bad throttle
Would something like a bad throttle or dirty throttle throw a mass air flow sensor code? That’s what happen in my case I replace the mass air flow but the code never went off. I come across your video and I clean the throttle body put everything back together cut the car on check engine light was on drove around the block cut the car off and back on the light went out, next day it come back on. Any idea as why it’s doing that? Thanks
@@danieldo6254 I’m here because i have that same exact issue right now. Gonna clean the throttle body out first and if it still stalls then i might just replace the sensor as well.
@@NpausAsHawj hey I end up replacing the fuel pump and got the oem sensor from Toyota and everything worked fine no check engine light no hesitation good to go hope that helps.
I have a 2013 Camry se 4 cylinder that sometimes vibrates at idle but only in gear, it goes away in park. Could this be the problem? Thanks
This can be the issue or engine mount. Try to notice where ur rpm is when ur idling and it’s vibrating if it below 700 then u can say this is the issue
same, let me know if you found anything out about it thanks
@@CriCKiD3 try cleaning the throttle body and the MAF sensor
@@scottg429 alrighty will do that soon thanks Scott! Appreciate it 👍👍
I have toyota camry 2004 (manual) When i run the car without airconditon the rpm is not drop but when i turn on the Aircondition car feel little bit shake then car when running about avobe 30+ speed the rpm is good but when car get reduced speed car shaking and when gear in neutral engine get stop plz tell me about the problem🙏🙏
Yes so when u put ac on it puts loan and this service for throttle maybe will help lot!!
ok lets do it tomorrow then i will tell you the result ❤️@@RBTheMechanic
@@sanjeetimran4651 ok update me
Check catalytic converter?
U have p0420 code
How do you reset check engine light?
After doing this my check engine light is on
Do it with scan tool
My 2015 camry le idles at 800 rmps when it's on park but when I put on drive or reverse it drops to 500 or 600 rpms and it shakes and the has turned off when I'm at a stop sign or red light.
Definitely sounds like it need throttle cleaning
Why is the idle speed so high after I wash it? how to lower
U can do idle relearn or drive around without any lights radio hear ac on so there is no load it will learn idle speed again
@@RBTheMechanic thanks
Great video and explanation