I am reticent to use less solvent. I've destroyed grips the first time I tried it myself and vowed that more solvent is better and makes the job easier Just my opinion
I completely agree, but I also don't do this often to have a solvent recovery setup like our expert here. I would like to know what most folks use to catch the solvent for the purpose of minimizing the mess. I find that I always end up with solvent all over my shoes.
@@eriknash8783 I use a disposable aluminum foil type 1/2 sheet pan ....it's about the length of a grip and catches 95% of the excess Super cheap @ costco or other retailers
Good video - always helpful. Call me old school but I still prefer sealing off the end of the shaft. This keeps any moisture (rust?) getting in when I wash off my grips. As to solvent spurt, I simply drape a small rag over the grip end during installation. Not exactly elegant but I'm not a business and only re-grip about once a year.
@gerrymorcom5001 true. I've Done that once too. But I had tapped the traditional way. Just smashed it to hard. I'm all graphite in the bag now anyways.
Good video. I thought I was alone regarding the venting issue and I too discovered the solvent didnt dry when tape sealed the butt end. Also you can get more back pressure and create more problems when putting on long putter grips. So I just tape and seal the butt then tale a loft tool and punch a hole in the tape in a split second.
I work in a pro shop and my boss (the pro) was telling me how to avoid the solvent spray on my clothes, now I know what he was talking about and will make sure to do it in the future. Thanks for the video
I have to say I’ve been working on clubs for almost 50 years and have found that clubs I’ve regripped that someone had twisted the tape and closed the end almost always had rust on the tape and butt of the shaft. I leave about 1/8” overhang, just enough to allow the grip to easily slide on.
Thanks for mentioning the airflow and humidity, AJ.. I've bought new irons 3 years ago and I've now had 3 of them having broken shafts, with the clubhead flying off.. The shafts were all from a very famous vendor, so after discussing this with my local clubmaker, we don't think that this was due to a batch of faulty shafts. We rather think it's a mix of me leaving the clubs in my car for almost all year round (they are often exposed to a lot of moisture and temperature swings this way), as well as having the tape sealing off the back and then me using the Arccos sensors to block off even that little hole. This way I'd trap any possible moisture build-up and that could cause corrosion on the inside of the shaft, leading to the faults. My changes were to now remove the clubs from the car every day and bring them inside my house, as well as doing what you're showing here when regripping them. I will also consider removing the arccos sensors periodically (or at least after rainy rounds/sessions) to provide more airflow so they can dry better.
@@EFGMC yeah, i learned that the hard way.. the only disadvantage is that I often drive by golf courses and like this I can't just decide to play 9 holes or go to the range for some practice spontaneously (which I used to do quite regularly)
I use a spray bottle that holds my solvent. Just spray butt end and couple sprays inside grip and good to go. Eliminates need for a drip tray as well not having space inside home
I have regripped a lot of old clubs. I have seen shafts start to rust from being in the bag and water (rain) going to the bottom and the clubs sitting in there.
Great tip on not wrapping the tape over the butt end. Will do this next time I regrip! I like that GolfWorks gripping station, like to buy one someday. I have the discontinued portable gripping station that’s a tray which attaches to a vice but I use it on a Craftsman portable work bench that closes like a vice.
I got a grip replacement kit that was bundled for free with my GP grips from an online retailer. It was some pre-cut tapes, a little bottle of solvent with a push-button pump sprayer, and a vise clamp shaft holder. The instructions specifically say to mist the tape and not pour or soak it. I put a few sprays in the grip, spun and shook it up, then about 4 sprays on the shaft to moisten the tape, top and bottom front and back. The grips just slide on no big deal. If your grips have a logo on the backside you just line it up with the shaft logo/lettering and you're pretty much bang on straight every time. Only a little solvent dribbled out the front as you push the grip on. No need for all these crazy stations, you can do it over a sink with the clubhead between your thighs. Rubber is easy. EVA-based grips like Jumbomax are a royal pain in the ass though.
Good news, I have regrouped a bunch of clubs and this is what I was doing, the shorter amount of tape. I did learn an easier way to remove the plastic on grips that have it. I tried using the disposable gloves to keep the solvent off my hands. I still use plenty of solvent to get the grip on and drench the shaft.
I use an even more efficient way to change grips. I cut the old ones off, then put the club in a vise and I have a tool that connects to my air compressor and the hole at the end of the grip goes into the port where air is expelled. You start the grip on the shaft, press the button and as air fills the shaft and the grip, the grip gets wider and slides right on. Also easy to twist/align. And there are two other benefits: 1 the grip does not slip and 2 you can switch grips easily at any time without damage to the grip. I bought some Pure grips years ago that came with this tool and have been using it ever since. Takes less than a minute to change a grip.
If I want two wraps of tape do I have to remove the old tape or can I just add new tape over the old tape thus giving me the two tapes I want? Thanks. Very helpful videos.
Good tips! I regrip quite often as I rarely wear a glove and absolutely love the feel of a good grip. With the grip materials and patterns these days, I sometimes wonder just how necessary a glove really is or is it more of a habit or something people automatically think is a must.
Yup. Find a grip you like and you don't need a glove. If anything, recent pressure sensor and EMG studies from tony Luczak would suggest the right hand runs the show. A need for extra left hand grip could be a sign of a technical fault.
I started playing 5 years ago and and started with a glove, i found after a few round that when i took it off to putt i forgot to put it back on again and did not realize till the end of the round that it was in my pocket, I use golf pride CP2 grip and hardly ever play in rain, I find a glove completely unneeded. have not used one the last 4 and a half years.
When you apply the tape, do you need to peel off the paper to expose the sticky part before putitng the grip on? Or does the solvent take care of that?
I use build up non dble sided tape plus a 1-2” piece on the butt. Spray solvent on just the dble sided. The blow on. Except for GP Align grips. Dble sided a must. Std slide on .
I use mineral spirits in a chemical resistant spray bottle. A few squirts down the grip mists the inside and then you just pour it out of the grip onto the tape. No solvent touches your hands and you use way less of it so it's more economical and the grips dry faster.
I always wondered why I’d heard the suggestion to seal the end of the shaft with the tape. I’ve used your new method from the get go haha. 🤙 I’ve also had the experience of having to clean some rust out of a few shafts i regripped, that were tape sealed from the previous grip job. Even if it did happen, you’d rather have dirt get into your shaft than rust.
Enjoy your channel and advice very much. Can you tell me if you have produced a video or have plans to, on replacing a two grip handle long putter grip. I need to replace my current two-piece grip and are not exactly sure of the best process. Thank you in advance for your consideration.
I have not but the method I use is to take a single very long piece of grip tape and run it the full length of where the 2 grip pieces will sit. Mark it with Sharpie where you want the lower one to sit. Use plenty of solvent and side the lower grip down into place followed by the top grip. Once dry, go back and cut away the extra tape between the 2 grips.
Enjoyed your videos. Here’s a tip I wish you had covered. Maybe I missed it. Be EXTREMELY careful with graphite shafts. I was using a vice and one of those hard rubber shaft holders and tightened to prevent the club turning and I heard a “snap”. Yep. Put a nice hairline fracture in the shaft. To prevent this, obviously don’t over tighten, but also place the rubber vice on the thickest part of the shaft closest to the grip. Also, I first learned using WD40 instead of “golf club solvent”. I haven’t checked but I think it’s much cheaper and works great.
I always poke a hole in the back of the tape with a tee, I think I learned that from Golfsmith years ago. I was using 3/4 inch spiral double sided tape then.
I suggest Royal Grip V Sandwrap rib. 'Been playing these for years gloveless. GolfWorks Grip Deals page 2. Buy 6 get 6 $24. Love the feel, love the price!
I was removing the top layer of tape before using solvent. For effiency, do I need to remove the second side of the tape, or will solvent take care of??
Yes, remove all backing paper from the tape before using solvent. My double sided tape dispenser pulls the backing off when you use it. That is why you don't see me peeling anything.
AJ, I personally use air for all my clubs but for anyone that I do regrippings for I use the solvent method. Not sure why, i've never had a failure with the air method, but just stick with the old school is best mentality for other peoples grips. What are your thoughts? I know you've used air as well in the videos, but just wondering as a general "what do you think" type thing. Happy New Year, keep up the great work and content!
It's funny that you mention that. I regripped my set of PXG clubs last year that still had the original grip on them from the factory. All of the factory installed grips (Golf Pride MCC) were applied using only masking tape. I never had an issue with them over 2 seasons and 60+ rounds - that's playing in the south (Atlanta) and I sweat a lot and have a relatively high swing speed (7 iron is about 94 mph). After seeing how well the masking tape performed, I'll never use solvent again. Just too many benefits to using masking tape and air (cheaper, easier to remove/adjust, no solvent, etc.).
Air installed grips can slip a little over time. Not an issue if you have the air compressor or inflator to straighten them back out, but if it's for other people I only use air with certain grips or if they request it.
Talking about grips, my favorite, Pure DTX Midsize, is no longer available. I also would build up the tapered end. Any recommendations for a replacement?
The Star grips are very close though they don't make a DTX style pattern. I am big on the Lamkin Hybrid ST+2 grips. They are softer, with good texture and reduced taper.
When putting on the new grip, how can I easily get it aligned properly? I use a workbench and shaft vice, but I don’t have anything to align the club head
How do you determine what is straight as far as aligning the slash on the grip with the golf head? Just had some done for the first time and it seems like they are lined up with more of a closed face than the stock grips were, one is way off? I check my face at setup so I can adjust, but I'm OCD and it's bugging me. LOL.
Hi! Great videos. I am a clubfitter/repairer from BC, Canada and have been in business since 2005 after attending Golfsmiths Training Facility in Austin, Texas for a week. I typically use the old tried/true method of grip removal/install cuz when i tried using compressed air to remove grips, quite often the grip blew apart! I watched both this video and the one comparing old tried/true method vs using compressed air method. Do u have a video where u specifically discuss what kind of compressor (I think u said 60 psi is needed) + attachment to compressor and tip to insert in grips butt end? I am very curious re ur info re taping end of shaft? It seems to me that u are giving conflicting info in that 1/ if u completely close off the end, it is better so that nothing incl rain/debris gets into the shaft to possibly cause corrosion w.r.t steel shafts vs 2/ if u leave a small hole for airflow, then not only will rain get in there but will u not also be shoving some grip solvent down the shaft? i.e. potential for corrosion. I am by no means an expert and am always willing to learn so may, once u provide some info re compressor/attachment etc the compressor method to install/remove grips. I will be warching more of your videos.......thanks and have a wonderful day!
60 psi is why you're blowing up grips. It doesn't take much pressure at all, maybe 15-20 psi. And there are 10,000 videos on this, find one and watch it
I use air but also use tape and solvent. Tape like normal but then spray jist a tiny bit of solvent inside the grip, drain the excess into the solvent bottle, then blow on with air. Doing this way you only need to very small amount of solvent and grips dry super fast.
I have purchased a set of Cleveland irons that are counterbalanced. I want replace the stander grips to midsize, will I have any problem, I imagine the counterbalance is in the end of the shaft. I have changed the grips on clubs before, but not this type, will I run into any problems that I don’t know about?
Hey- not sure if you’ve done this already (so apologizes if this is a duplicate request) but would you be able to link your grip changing system components? Tub-vice grip etc? I’ve been changing mine in my tub sink w no vice for years and it’s time to get something a bit more reliable. Thanks!
What I am using now is the Golfworks gripping station. It includes everything (vice clamp, drip pan, double sided tape and single sided tape dispenser. www.golfworks.com/maltby-design-floor-mount-gripping-station/p/ma2016/
Air compressor is the way to go. You can use regular masking tape and then just dip the open end of the grip in the solvent and blow the grip on. It's ready to go immediately. Less solvent and cheaper tape.
Great videos, totally new to this. I see the tape that you use is sticky on the side you place on the club but is the other side activated by the solvent or is there a layer you peel off and then apply solvent?
I haven’t used grip solvent in about 5 years now…I blow all my grips on and off with a compressor…much more efficient, cheaper, and allows me to easily swap out my grips depending on conditions…e.g., I’ll use softer grips in the winter than the summer, and I’ll use one in the summer that deal with sweat better…then, I just swap out grips without losing a grip…
I charge $30 for a full reshaft which includes gripping and any standard adjustment. I think big box stores are around $20-$25 but that's a roll of the dice taking clubs somewhere like that.
The only benefit is drying a bit faster. Smells 'cleaner' because it's more refined. For this application, it's the same as mineral spirits. Now, getting in the weeds, Naptha is less greasy .
Great video, wishing you a happy and prosperous new year. I wonder if not capping off the shaft with tape also gives a little more feel to the shafts 🤔. Any tips for regripping and getting any alignment aids on the grips perfectly aligned with the leading edge?
I always eyeball it. My gripping station is angled into a corner so I can use the wall to ensure the club face is straight. Then I just align the grip off that face position.
This isn't a comment on this video, rather a question on one of your videos from 4 years ago I have just watched re is there a difference in shortening a shaft or gripping down, if you went along the road of cutting down would this alter the flex of the shaft ?
Short answer is not much. Long answer is it's complicated. If you butt cut the shaft, the frequency of the shaft will go up. However this is misleading because you are actually cutting away the stiffest portion of the shaft so the remaining area is actually softer. That said, the actual amount of change with most butt cutting will be too small to worry about.
So double sided tape is used but only sticks to the shaft? Seemed like the paper wasn’t removed from the other side of the tape before the grip was put on?
@EFGMC I think the golf pride mcc grips were fakes too. So thst could have something to do with it. One season. Father in laws grips were hard and glossy
When you have shown how easily you blow a grip on with compressed air, why do you still use the solvent method? Did you find that the grips were moving on you?
Hi.Just clean your shaft from everythings from the old grip and use an air compressor in the little hole of your grip and give a little pressure and it will go in easily.The most important thing is you dont need any new tape at all.the grip stick to the clean shaft like if you would add a double face tape.No more tape ever.No mess with the liquid and etc... Yvon Masse
When regripping several sets of clubs one after another, the technique of banging the butt of the grip on the bench to remove the plastic becomes a problem. My hand would be sore at the end of the day from banging it. I found that a better technique is to grab the plastic section with both hands and twist in opposite directions as if you are ringing water out of a towel. This takes the plastic off just as fast or faster with no banging.
You inspired me to build clubs. Why not do a video on tapping and rethreading the bottom of a wood like a seven word that does not have adjustable screw weights in the back this would be a nice way to add weight to the bottom and back of a wood without using lead tape
Still there but I try and cover all the methods that people use. Might bring back the rubber cement method again as I haven't covered that one in a long time.
I have used air for about a year now and it is awesome. Has anyone had any luck using air with a Super Stroke Putter Grip? I tried it once, had to increase the PSI from 50 to about 80 and it inflated and split the skin off the grip and it still wouldn't go on. Had to use solvent (on a new grip) and even then it was a challenge. Thank you
Certain grips don't work as well with air including cord grips and Winn grips. Also air installed grips can move over time a little. Not a big deal to put some more air in and straighten them up but it can happen.
Maybe it doesn't rain where you are, but an open end in the butt, and a wet bag, seems like an easy way to let moisture wick into the shaft and create that corrosion you reckon leaving the end open will prevent.
It has a backing on it but my tape dispenser automatically removes it when pulled through. Doubled sided tape dispenser is maybe the best tool you can get if you do more than a couple regrips at a time.
I have been cheating and not taking off the old tape if it’s perfect condition when I remove the old grip. Doesn’t seem to be a problem. I never saw you remove the protective coating off the two sided tape. I assume you did?
Mostly you don’t want water to get inside the shaft which will cause corrosion. And if you don’t jam the grip on with such gusto, you won’t get sprayed.
I'm a bit late to the party here but I have a question. Do you need solvent? I'm sure I saw a video where someone just used water. If this works you'll save money and avoid dangerous chemicals.
They sell water activated tape that will work however I have always seem very mixed reviews of it. Standard grip tape will require some kind of solvent.
Anyone here ever seen the inside of steel shafts left exposed to moisture and the elements over the long term by not covering the hole with tape? Is it even anything to be concerned about?
I watched your video about blowing grips on (and off) with air. Started doing that and never looked back. Absolutely the best method in my opinion.
I am reticent to use less solvent. I've destroyed grips the first time I tried it myself and vowed that more solvent is better and makes the job easier Just my opinion
I completely agree, but I also don't do this often to have a solvent recovery setup like our expert here. I would like to know what most folks use to catch the solvent for the purpose of minimizing the mess. I find that I always end up with solvent all over my shoes.
@@eriknash8783 I use a disposable aluminum foil type 1/2 sheet pan ....it's about the length of a grip and catches 95% of the excess Super cheap @ costco or other retailers
Good video - always helpful. Call me old school but I still prefer sealing off the end of the shaft. This keeps any moisture (rust?) getting in when I wash off my grips. As to solvent spurt, I simply drape a small rag over the grip end during installation. Not exactly elegant but I'm not a business and only re-grip about once a year.
It also stops moisture getting out. The paper isn't water proof. I've been putting grips on like this for years. Never got debris or rust.
Using 1/4” tape to overlap the shaft helps prevent the butt end of the shaft from slicing thru the butt end of the grip.
@gerrymorcom5001 true. I've Done that once too. But I had tapped the traditional way. Just smashed it to hard. I'm all graphite in the bag now anyways.
Good video. I thought I was alone regarding the venting issue and I too discovered the solvent didnt dry when tape sealed the butt end. Also you can get more back pressure and create more problems when putting on long putter grips. So I just tape and seal the butt then tale a loft tool and punch a hole in the tape in a split second.
Completely agree with all your tips. Been doing these for years and it’s way less messy. Thanks for validating this!
I work in a pro shop and my boss (the pro) was telling me how to avoid the solvent spray on my clothes, now I know what he was talking about and will make sure to do it in the future. Thanks for the video
Simple tips but worth changing to this approach. Can't wait to try out on my next re-grip. Really enjoy your channel.
I have to say I’ve been working on clubs for almost 50 years and have found that clubs I’ve regripped that someone had twisted the tape and closed the end almost always had rust on the tape and butt of the shaft. I leave about 1/8” overhang, just enough to allow the grip to easily slide on.
Thanks for mentioning the airflow and humidity, AJ.. I've bought new irons 3 years ago and I've now had 3 of them having broken shafts, with the clubhead flying off.. The shafts were all from a very famous vendor, so after discussing this with my local clubmaker, we don't think that this was due to a batch of faulty shafts. We rather think it's a mix of me leaving the clubs in my car for almost all year round (they are often exposed to a lot of moisture and temperature swings this way), as well as having the tape sealing off the back and then me using the Arccos sensors to block off even that little hole. This way I'd trap any possible moisture build-up and that could cause corrosion on the inside of the shaft, leading to the faults.
My changes were to now remove the clubs from the car every day and bring them inside my house, as well as doing what you're showing here when regripping them. I will also consider removing the arccos sensors periodically (or at least after rainy rounds/sessions) to provide more airflow so they can dry better.
Best practice to never keep clubs in your car. Anything bad will be sped up in that environment.
@@EFGMC yeah, i learned that the hard way.. the only disadvantage is that I often drive by golf courses and like this I can't just decide to play 9 holes or go to the range for some practice spontaneously (which I used to do quite regularly)
I use a spray bottle that holds my solvent. Just spray butt end and couple sprays inside grip and good to go. Eliminates need for a drip tray as well not having space inside home
Same here, quick spray on the tape, two squirts inside the grip and slide on. Much less solvent, less mess, less time.
I have regripped a lot of old clubs. I have seen shafts start to rust from being in the bag and water (rain) going to the bottom and the clubs sitting in there.
Great tip on not wrapping the tape over the butt end. Will do this next time I regrip! I like that GolfWorks gripping station, like to buy one someday. I have the discontinued portable gripping station that’s a tray which attaches to a vice but I use it on a Craftsman portable work bench that closes like a vice.
I liked the information. Undecided if I’ll use this or masking tale with air compressor.
I only use compressed air to demo/test grips. I find it's not secure. I use tape and solvent after I have tested grips
I love it; I built a solvent tube with a cap. I dip the shaft in the tube and slide my grip on it. I have it mounted to a bucket for excess dripping.
Excellent new ideas! Much more efficient regripping process….speaking as a retired Process Engineer. Well done sir!
You have the best job in the world. I would love to do what you do. Awesome tips
I got a grip replacement kit that was bundled for free with my GP grips from an online retailer. It was some pre-cut tapes, a little bottle of solvent with a push-button pump sprayer, and a vise clamp shaft holder. The instructions specifically say to mist the tape and not pour or soak it. I put a few sprays in the grip, spun and shook it up, then about 4 sprays on the shaft to moisten the tape, top and bottom front and back. The grips just slide on no big deal. If your grips have a logo on the backside you just line it up with the shaft logo/lettering and you're pretty much bang on straight every time. Only a little solvent dribbled out the front as you push the grip on. No need for all these crazy stations, you can do it over a sink with the clubhead between your thighs. Rubber is easy.
EVA-based grips like Jumbomax are a royal pain in the ass though.
Good news, I have regrouped a bunch of clubs and this is what I was doing, the shorter amount of tape. I did learn an easier way to remove the plastic on grips that have it.
I tried using the disposable gloves to keep the solvent off my hands. I still use plenty of solvent to get the grip on and drench the shaft.
Great tip on the solvent, totally using that method from now on
I use an even more efficient way to change grips. I cut the old ones off, then put the club in a vise and I have a tool that connects to my air compressor and the hole at the end of the grip goes into the port where air is expelled. You start the grip on the shaft, press the button and as air fills the shaft and the grip, the grip gets wider and slides right on. Also easy to twist/align. And there are two other benefits: 1 the grip does not slip and 2 you can switch grips easily at any time without damage to the grip. I bought some Pure grips years ago that came with this tool and have been using it ever since. Takes less than a minute to change a grip.
Doesn't the solvent activate the glue?
If I want two wraps of tape do I have to remove the old tape or can I just add new tape over the old tape thus giving me the two tapes I want? Thanks. Very helpful videos.
That works.
@@EFGMC Thanks!
I have always done it the way the first two tips are described, but tip 3 is a good one as well. 👏
Good tips! I regrip quite often as I rarely wear a glove and absolutely love the feel of a good grip. With the grip materials and patterns these days, I sometimes wonder just how necessary a glove really is or is it more of a habit or something people automatically think is a must.
yeaaa no glove crew
Yup. Find a grip you like and you don't need a glove. If anything, recent pressure sensor and EMG studies from tony Luczak would suggest the right hand runs the show. A need for extra left hand grip could be a sign of a technical fault.
I started playing 5 years ago and and started with a glove, i found after a few round that when i took it off to putt i forgot to put it back on again and did not realize till the end of the round that it was in my pocket, I use golf pride CP2 grip and hardly ever play in rain, I find a glove completely unneeded. have not used one the last 4 and a half years.
I wonder also about a glove. I can’t stand a glove after the second hole. I channel my inner Fred Couples.
@@jeffnahass8373 ya just keep your grips clean. and if you put gloveless it speeds up play. one less gubbin to faf with on the course.
When you apply the tape, do you need to peel off the paper to expose the sticky part before putitng the grip on? Or does the solvent take care of that?
Any recommendations on grip tape and solvent?
I use build up non dble sided tape plus a 1-2” piece on the butt. Spray solvent on just the dble sided. The blow on. Except for GP Align grips. Dble sided a must. Std slide on .
I use mineral spirits in a chemical resistant spray bottle. A few squirts down the grip mists the inside and then you just pour it out of the grip onto the tape. No solvent touches your hands and you use way less of it so it's more economical and the grips dry faster.
Great tips, I will change to these methods as well. Thank you 👍
I always wondered why I’d heard the suggestion to seal the end of the shaft with the tape. I’ve used your new method from the get go haha. 🤙 I’ve also had the experience of having to clean some rust out of a few shafts i regripped, that were tape sealed from the previous grip job. Even if it did happen, you’d rather have dirt get into your shaft than rust.
Hi could you put out a video on extending a set of irons?
Great content on re-gripping 👍
Enjoy your channel and advice very much. Can you tell me if you have produced a video or have plans to, on replacing a two grip handle long putter grip. I need to replace my current two-piece grip and are not exactly sure of the best process. Thank you in advance for your consideration.
I have not but the method I use is to take a single very long piece of grip tape and run it the full length of where the 2 grip pieces will sit. Mark it with Sharpie where you want the lower one to sit.
Use plenty of solvent and side the lower grip down into place followed by the top grip. Once dry, go back and cut away the extra tape between the 2 grips.
Enjoyed your videos. Here’s a tip I wish you had covered. Maybe I missed it. Be EXTREMELY careful with graphite shafts. I was using a vice and one of those hard rubber shaft holders and tightened to prevent the club turning and I heard a “snap”. Yep. Put a nice hairline fracture in the shaft. To prevent this, obviously don’t over tighten, but also place the rubber vice on the thickest part of the shaft closest to the grip. Also, I first learned using WD40 instead of “golf club solvent”. I haven’t checked but I think it’s much cheaper and works great.
I always poke a hole in the back of the tape with a tee, I think I learned that from Golfsmith years ago. I was using 3/4 inch spiral double sided tape then.
I actually think this is the best of both worlds!
Thanks for this instruction. Can i ask what grips would you recommend , as i do not use a glove?. Currently i use golf pride.
Do you prefer tacky rubber feel or rough cord type feel?
@@EFGMC rubber feel I would prefer.
@@petera2133 Pure grips (if you can still get them), Star Grips, Golf Pride Tour Wrap (current generation), or CP2.
I suggest Royal Grip V Sandwrap rib. 'Been playing these for years gloveless. GolfWorks Grip Deals page 2. Buy 6 get 6 $24. Love the feel, love the price!
I was removing the top layer of tape before using solvent. For effiency, do I need to remove the second side of the tape, or will solvent take care of??
Yes, remove all backing paper from the tape before using solvent. My double sided tape dispenser pulls the backing off when you use it. That is why you don't see me peeling anything.
AJ, I personally use air for all my clubs but for anyone that I do regrippings for I use the solvent method. Not sure why, i've never had a failure with the air method, but just stick with the old school is best mentality for other peoples grips. What are your thoughts? I know you've used air as well in the videos, but just wondering as a general "what do you think" type thing.
Happy New Year, keep up the great work and content!
It's funny that you mention that. I regripped my set of PXG clubs last year that still had the original grip on them from the factory. All of the factory installed grips (Golf Pride MCC) were applied using only masking tape. I never had an issue with them over 2 seasons and 60+ rounds - that's playing in the south (Atlanta) and I sweat a lot and have a relatively high swing speed (7 iron is about 94 mph). After seeing how well the masking tape performed, I'll never use solvent again. Just too many benefits to using masking tape and air (cheaper, easier to remove/adjust, no solvent, etc.).
Air installed grips can slip a little over time. Not an issue if you have the air compressor or inflator to straighten them back out, but if it's for other people I only use air with certain grips or if they request it.
Talking about grips, my favorite, Pure DTX Midsize, is no longer available. I also would build up the tapered end. Any recommendations for a replacement?
The Star grips are very close though they don't make a DTX style pattern. I am big on the Lamkin Hybrid ST+2 grips. They are softer, with good texture and reduced taper.
Good news ! Star is developing a textured grip for this year.
I always thought it was to keep solvent from going down the shaft and sitting against the epoxy holding the head on?
When putting on the new grip, how can I easily get it aligned properly? I use a workbench and shaft vice, but I don’t have anything to align the club head
I like to add a little solvent to get it started, then finish with air, no solvent on the tape.
How do you determine what is straight as far as aligning the slash on the grip with the golf head? Just had some done for the first time and it seems like they are lined up with more of a closed face than the stock grips were, one is way off? I check my face at setup so I can adjust, but I'm OCD and it's bugging me. LOL.
If they bother you, that's all that matters. If you think a grip is straight, it's straight.
Hi! Great videos. I am a clubfitter/repairer from BC, Canada and have been in business since 2005 after attending Golfsmiths Training Facility in Austin, Texas for a week. I typically use the old tried/true method of grip removal/install cuz when i tried using compressed air to remove grips, quite often the grip blew apart! I watched both this video and the one comparing old tried/true method vs using compressed air method. Do u have a video where u specifically discuss what kind of compressor (I think u said 60 psi is needed) + attachment to compressor and tip to insert in grips butt end? I am very curious re ur info re taping end of shaft? It seems to me that u are giving conflicting info in that 1/ if u completely close off the end, it is better so that nothing incl rain/debris gets into the shaft to possibly cause corrosion w.r.t steel shafts vs 2/ if u leave a small hole for airflow, then not only will rain get in there but will u not also be shoving some grip solvent down the shaft? i.e. potential for corrosion. I am by no means an expert and am always willing to learn so may, once u provide some info re compressor/attachment etc the compressor method to install/remove grips. I will be warching more of your videos.......thanks and have a wonderful day!
60 psi is why you're blowing up grips. It doesn't take much pressure at all, maybe 15-20 psi. And there are 10,000 videos on this, find one and watch it
I use air but also use tape and solvent. Tape like normal but then spray jist a tiny bit of solvent inside the grip, drain the excess into the solvent bottle, then blow on with air. Doing this way you only need to very small amount of solvent and grips dry super fast.
I have purchased a set of Cleveland irons that are counterbalanced. I want replace the stander grips to midsize, will I have any problem, I imagine the counterbalance is in the end of the shaft. I have changed the grips on clubs before, but not this type, will I run into any problems that I don’t know about?
Should just be a plug in the butt end. No change regripping.
Awesome video as always! I do a very similar process just using the HF100 spray to reduce the required lubricant as much as possible 👌
Hey- not sure if you’ve done this already (so apologizes if this is a duplicate request) but would you be able to link your grip changing system components? Tub-vice grip etc? I’ve been changing mine in my tub sink w no vice for years and it’s time to get something a bit more reliable. Thanks!
What I am using now is the Golfworks gripping station. It includes everything (vice clamp, drip pan, double sided tape and single sided tape dispenser.
www.golfworks.com/maltby-design-floor-mount-gripping-station/p/ma2016/
Thank you! Keep up the great work and collabs w other creators!
Air compressor is the way to go. You can use regular masking tape and then just dip the open end of the grip in the solvent and blow the grip on. It's ready to go immediately. Less solvent and cheaper tape.
Great videos, totally new to this. I see the tape that you use is sticky on the side you place on the club but is the other side activated by the solvent or is there a layer you peel off and then apply solvent?
Never mind just saw your other video where you explained it.
I haven’t used grip solvent in about 5 years now…I blow all my grips on and off with a compressor…much more efficient, cheaper, and allows me to easily swap out my grips depending on conditions…e.g., I’ll use softer grips in the winter than the summer, and I’ll use one in the summer that deal with sweat better…then, I just swap out grips without losing a grip…
What would a typical charge be to change the shaft on an iron and add a new grip?
I charge $30 for a full reshaft which includes gripping and any standard adjustment. I think big box stores are around $20-$25 but that's a roll of the dice taking clubs somewhere like that.
Does your double sided tape not have backing tape to peel off? Or did you already peel it off or do you not peel it off and just wet with fluid?
My tape dispenser pull the backing off automatically.
I have always used water based tape and a little dishsoap suds. No chemical issues. Last me hundreds of rounds with no issues.
I use Naptha for regripping. Is that better than Mineral Spirits or no difference?
Think its about the same but someone here might have a more detailed answer.
Nathan is a more highly refined spirit. It is a little more expensive, dries quicker, but still nasty on your skin. (I'm a painting contractor. )
The only benefit is drying a bit faster. Smells 'cleaner' because it's more refined. For this application, it's the same as mineral spirits. Now, getting in the weeds, Naptha is less greasy .
Thank you for the information.
Great video, wishing you a happy and prosperous new year.
I wonder if not capping off the shaft with tape also gives a little more feel to the shafts 🤔.
Any tips for regripping and getting any alignment aids on the grips perfectly aligned with the leading edge?
I always eyeball it. My gripping station is angled into a corner so I can use the wall to ensure the club face is straight. Then I just align the grip off that face position.
This isn't a comment on this video, rather a question on one of your videos from 4 years ago I have just watched re is there a difference in shortening a shaft or gripping down, if you went along the road of cutting down would this alter the flex of the shaft ?
Short answer is not much. Long answer is it's complicated. If you butt cut the shaft, the frequency of the shaft will go up. However this is misleading because you are actually cutting away the stiffest portion of the shaft so the remaining area is actually softer.
That said, the actual amount of change with most butt cutting will be too small to worry about.
Thanks
So double sided tape is used but only sticks to the shaft? Seemed like the paper wasn’t removed from the other side of the tape before the grip was put on?
I use a double sided tape dispenser that automatically removes the backing paper. Maybe the most important tool in the shop for efficiency.
@@EFGMCyes on the side sticking to the club but not the side that’s in contact with the grip, that backing was still on?
@@andy-youtube314 Double sided tape dispenser removes all the paper so you pull out a piece of tape sticky on both sides.
Where'd you get the Fuji apron, i want it
From my Fuji rep!
Makes a lot of sense to streamline the gripping process.
Makes sense and I’ll be using this method. Thanks 👍
I used air once. blew a hole in the side of the grip. loud as a gunshot. Probably too much PSI
Mine is set to 58psi
@EFGMC I think the golf pride mcc grips were fakes too. So thst could have something to do with it. One season. Father in laws grips were hard and glossy
I just tape (3 sets of my own) right to the end of the shaft. Tape even with the end. Tape never sticks out of opposite end.
When you have shown how easily you blow a grip on with compressed air, why do you still use the solvent method? Did you find that the grips were moving on you?
I'm getting a lot of questions like this. My video next week is going to cover everything about tape and solvent vs air install regripping.
Would you please mention if it is possible to install a Jumbomax Ultralite grip by an air compressor method? Thank you.@@EFGMC
@@TSOSGERBY The Ultralite is actually pretty easy to get on with air. The other Jumbomax grips are far more difficult.
Please tell me the amount of pressure I should use to install a JMX Ultralite grip? Thank you@@EFGMC
@@TSOSGERBY 55-60psi is plenty
That's actually the way I was first taught to regret if you use the tire inflator can you use regular grip tape
Wondering if there are any issues that might arise when solvent runs down the shaft using this “unsealed” method?
Alignment tips?
AJ. Did you take off the white cover of the tape, the video looks like you left it on ?.
The double sided tape dispenser pulls the backing off automatically.
@@EFGMC Ah!, modern technology. Really enjoy looking at your video’s.
Hi.Just clean your shaft from everythings from the old grip and use an air compressor in the little hole of your grip and give a little pressure and it will go in easily.The most important thing is you dont need any new tape at all.the grip stick to the clean shaft like if you would add a double face tape.No more tape ever.No mess with the liquid and etc... Yvon Masse
Is mineral spirits a decent solvent to use, what's Golf Works formula base?
Thanks, love your channel....... Subbed
Yes, and yes it's mineral spirits based I believe.
So do you prefer solvent versus an air compressor?
Depends on the grip. Soft rubber grips are great with air. Harder, corded, Winn style, or grips with reminder ribs, I usually stick with solvent.
With your favorite grip and mine-Pure- no longer being made, which grips do you still plan to install with air?
Will be switching to Star Grips for the studio. Any softer rubber grips work well. Tour Velvet 360, Tour Wraps, etc.
When regripping several sets of clubs one after another, the technique of banging the butt of the grip on the bench to remove the plastic becomes a problem. My hand would be sore at the end of the day from banging it. I found that a better technique is to grab the plastic section with both hands and twist in opposite directions as if you are ringing water out of a towel. This takes the plastic off just as fast or faster with no banging.
What is the solvent? Mineral spirits?
I have always just used WD40. Works great.
It's Golfworks grip solvent which I believe is mineral spirits based.
I've done virtually the same thing but I just use something like a screwdriver and poke a hole and it works the same way.
Very nice…… will do all in the future…. Ty
Can u help me with the best Midsize grip maximum 55gram. Tnx 🙏
Probably should go with Winn. They make a number of mid and oversize grips that weigh out close to a standard size rubber grip.
You inspired me to build clubs. Why not do a video on tapping and rethreading the bottom of a wood like a seven word that does not have adjustable screw weights in the back this would be a nice way to add weight to the bottom and back of a wood without using lead tape
What happened to the air method?
Still there but I try and cover all the methods that people use. Might bring back the rubber cement method again as I haven't covered that one in a long time.
I have used air for about a year now and it is awesome. Has anyone had any luck using air with a Super Stroke Putter Grip? I tried it once, had to increase the PSI from 50 to about 80 and it inflated and split the skin off the grip and it still wouldn't go on. Had to use solvent (on a new grip) and even then it was a challenge. Thank you
Trottie with Taylormade breaks the label by slamming it on the table as well.
Why choose solvent over using the air compressor to install a grip?
Certain grips don't work as well with air including cord grips and Winn grips. Also air installed grips can move over time a little. Not a big deal to put some more air in and straighten them up but it can happen.
@@EFGMC Thanks for the reply:)
Great tips AJ
You always have good advice. Thanks!
Maybe it doesn't rain where you are, but an open end in the butt, and a wet bag, seems like an easy way to let moisture wick into the shaft and create that corrosion you reckon leaving the end open will prevent.
Great tips. Thanks
I thought when using 2 sided tape, you were suppose to peel off the outside wrapper and install the grip with a sticky tape surface?
his tape isnt the peel off type, it double sided but the outside needs solvent to activate the glue as it dry on the roll.
It has a backing on it but my tape dispenser automatically removes it when pulled through. Doubled sided tape dispenser is maybe the best tool you can get if you do more than a couple regrips at a time.
I like all these ideas; I'll give it a go next time I regrip. Last time I gripped it took 4 days to dry using the old no air flow method.
good tip as always.
I use air to install and buy Starr grips. No tape needed. On and off in a few seconds. Zero chance I'd use mineral spirits again.
Aquanet Hair spray contains super glue. I just spray the shaft and boom, after 30 min I'm golfing.
super glue on your hair!
cyanoacrylate Is in Super Glue but it is also in hair spray!
If you use Naptha you can be playing in 5 mins !!
I have been cheating and not taking off the old tape if it’s perfect condition when I remove the old grip. Doesn’t seem to be a problem. I never saw you remove the protective coating off the two sided tape. I assume you did?
Double sided tape dispenser! Must have for anyone doing more than a few regrips.
Excellent..thanks
Mostly you don’t want water to get inside the shaft which will cause corrosion. And if you don’t jam the grip on with such gusto, you won’t get sprayed.
I do everything with gusto 😀
@ then remember to wear your apron.
In decades, I’ve never taped a grip, always alcohol & air compressor. Never had one come off. 😮
I'm a bit late to the party here but I have a question. Do you need solvent? I'm sure I saw a video where someone just used water.
If this works you'll save money and avoid dangerous chemicals.
They sell water activated tape that will work however I have always seem very mixed reviews of it. Standard grip tape will require some kind of solvent.
Why do you guys use so much solvent . I brush it on with a tiny squirt inside .
It always made no sense to me to block the shaft end off from air - especially steel shafts.
Use compressed air to get the grip off
This is now my new technique.
Anyone here ever seen the inside of steel shafts left exposed to moisture and the elements over the long term by not covering the hole with tape? Is it even anything to be concerned about?
Don't you have a method of not using double sided tape and just regular masking tape? Put the grip on with an air compressor?
Yes, it just depends on the grip you are using for which method I prefer.
I some use double sided tape but still use solvent. The pressure from the grip holds it in i just use more tape cause i like them thicker