@robodurden I would like to ask for assistance with using this controller. I have succesfully set all the pins using the pinfinder firmware and flashed the main firmware. I cant seem to get the esp32 code to work/ spin the motor. I am using the MM32SPIN06PF Board (just one) with the DOIT ESP32 DEVKIT V1 using the Rx2 and Tx2 Uart pins. Help needed.
A great honor for me that you visit my little channel here. The "awesome" job is yours, not mine. I want to ask if we can dream that you will port your better firmware to GD32. Next, I may make an efficiency comparison between your sinusodial drive mode to the bad old GD32 Gen2 firmware and to the simpleFOC Gen2 firmware. And i will not be surprised when your MM32 firmware is on par with FOC motor control when only energy efficency is on test.
@@robodurden it is possible to port this to stm32f103/gd32f103, but we already have gen1 so theres no point the gd32f130 does not have hal library so it cannot be ported/can be ported but will take allot of effort to adapt the f103 library to f130 since mm32 board is built down to this $2 price i dont think theres any point anyways the sine wave mode is definitely a huge improvement for effiency and torque,especially at low speed,i would love to see the comparason of mm vs gd vs gen1too but im pretty sure for now the sine wave mode on gen1 is still better, because the hall sensor mechanical position is not calibrated yet, so some minor vibration is still caused
I have a dozen hoverboards that use the MM32Spin27 processor. I am wondering if it might be easier to just swap in a STM32F103 chip. I read somewhere the MM32 are pin compatible with the STM32F103. I have a handful of other hoverboards that use the STM32F103 chip. I am already familiar with writing and downloading code for the STM32. There are cheap STM32F103 chips on aliexpress, I wonder if they are fake and just MM32 chips? lol I'm impressed you were able to get new code flashed to the MM32, I'd guess if this works no need to swap chips?
@robodurden I would like to ask for assistance with using this controller. I have succesfully set all the pins using the pinfinder firmware and flashed the main firmware. I cant seem to get the esp32 code to work/ spin the motor. I am using the MM32SPIN06PF Board (just one) with the DOIT ESP32 DEVKIT V1 using the Rx2 and Tx2 Uart pins. Help needed.
Open an issue in one of our github repos..
i am the author of this firmware,feel free to ask any questions
A great honor for me that you visit my little channel here. The "awesome" job is yours, not mine. I want to ask if we can dream that you will port your better firmware to GD32. Next, I may make an efficiency comparison between your sinusodial drive mode to the bad old GD32 Gen2 firmware and to the simpleFOC Gen2 firmware. And i will not be surprised when your MM32 firmware is on par with FOC motor control when only energy efficency is on test.
@@robodurden it is possible to port this to stm32f103/gd32f103, but we already have gen1 so theres no point
the gd32f130 does not have hal library so it cannot be ported/can be ported but will take allot of effort to adapt the f103 library to f130
since mm32 board is built down to this $2 price i dont think theres any point anyways
the sine wave mode is definitely a huge improvement for effiency and torque,especially at low speed,i would love to see the comparason of mm vs gd vs gen1too
but im pretty sure for now the sine wave mode on gen1 is still better, because the hall sensor mechanical position is not calibrated yet, so some minor vibration is still caused
@@lifeai1889 the problem is that gen1 hoverboards are becoming difficult to find. A port at least of the potentiometer function would be very useful.
I have a dozen hoverboards that use the MM32Spin27 processor. I am wondering if it might be easier to just swap in a STM32F103 chip. I read somewhere the MM32 are pin compatible with the STM32F103. I have a handful of other hoverboards that use the STM32F103 chip. I am already familiar with writing and downloading code for the STM32. There are cheap STM32F103 chips on aliexpress, I wonder if they are fake and just MM32 chips? lol I'm impressed you were able to get new code flashed to the MM32, I'd guess if this works no need to swap chips?
@@murraymadness4674 mm32 spin2x series is supported mass producing is also supported in this firmware you can build your own binary for mass produce