In this case, had no effect. I have compared files recently and the difference was only the immo line. If it wouldn't start or something I agree, you must desolder it.
Hi, I always get this fault code Current programmer: CH341 20:50:13 IC not responding What can I do? I already soldered the IC to the board Thanks for your help!
@@Gadomaitis I tried everything for hours. Then found out that my ch341 has the 3.3 . 5V problem. I fixed that but I can't read the chip. Maybe I broke the chip with the 5v
@@stefankefer8384 Honestly, I wouldn't even think about this kind of a solution. I saw that you can place a jumper for 5V, but it's needed rarely( personally never used it) and CH341 comes from the suppliers prepared for 3V.
@@Gadomaitis Hi, the CH341 Works now with Chips i bought new. With the Immo Chip it don't work. I think it's broken due to the 5V before. Do you have a file that I can write on a new Chip so the ECU is working again. Thank you!
Not possible, it must work on this ECU. Do you do everything correctly? You can switch it off manually inserting 60 in that exact location. You can find it in this video. ruclips.net/video/qZ49hE5sHd4/видео.htmlsi=GEp8CiJCQ31FeWjy&t=226
Hello! when I read the eeprom everything is always 00000. I've also tried a me 3.8, it's always the same. everything is zero. but he says the eeprom was recognized! only he reads nothing. Tried an EDC15P+ twice. with both he reads the eeprom! only not with all MSA and so on. everything is always 0 Please help me
Hi, it must be bad connection or wrong polarity of first pin. Or have you picked the right component to read from the list? I mean does it really matches what you pick and what you want to read? Have you desoldered EPROM?
Hello and thank you for your answer! I used a SOP8 clip. I used it to read 2 EDC15P+ Eproms without any problems (only for testing). Then I tried a Bosch ME 3.8 and everything 0000 is displayed here. Next was an EDC15V, here also everything 0000. Then another Bosch ME 7.3 and here everything is 0000. Then I connected the EDC15P+ again and everything works. I just do not understand. Today I will unsolder the eprom and try if they are then read out.
@@Gadomaitis Yes I'm sure. My EDC15V is exactly the same as in your video. I did everything exactly like you, but it doesn't work. everything up to 0000.
@@mubert4676 check in the application, which you are using to program the eeprom, there should be such thing as "check connection" or something like that. Did you choose the right eeprom to program from the list? Another thing, 1st leg must be the right one, important part not to miss it, otherwise you can get 00.
What is this red cable u unplug from your CH341 programmer? Becaus i tried your way But if i connect the clamp to the Chip my CH341 programmer Turns off because of lack of Power i dont know?
@@istealvideos7834 I see, it's a cable tie, just to lift the programmer, as it had no communication. Later that day I have resoldered USB pins to PCB, and since then, no need of a such mod
Yeah i See they dont work good on those programmer my Test Clip was missing 2 Pins they were Not solder Right. I Fix the Clip now it Work linke it should thx for the help
Sorry for inconveniec and thanks for your feedback. It happens when doing everything all by my self. Make sure to select 1020 HD video quality and NOT auto 1020 HD, sometimes it makes the difference.
![BabyChiefDoit - Too Slow (feat. STAR BANDZ) [Official Music Video]](http://i.ytimg.com/vi/zayaxws7RPg/mqdefault.jpg)
![KAYTRANADA - Witchy (feat. Childish Gambino) [Official Video]](http://i.ytimg.com/vi/jGK3YVmGZ3Y/mqdefault.jpg)
another thing, it is not possible to program the eprom on the ecu, but you have to unsolder the eprom
Not necessarily. It depends.
Too much noise in data while on the board I think. Desoldering can help to not corrupt info either
In this case, had no effect. I have compared files recently and the difference was only the immo line. If it wouldn't start or something I agree, you must desolder it.
Nice video.
Thanks.
One more big like!
Thanks mate!
Vag cam commander 1.4 read this ecu k-line fvdi chip.sorry, you car old and not having OBD2.good idea
Yes, this isn't OBD2. Any ways, this is a very pocket friendly solution, unless VAG COM commander is not expensive.
Thank you for the video! Do you have XDF files for edc15v?
Drop me an email, what file you need
VW transporter diesel?am from rassua my English is so so.good video thank you
Thanks, Cheers, G.
Hi, I always get this fault code
Current programmer: CH341
20:50:13
IC not responding
What can I do? I already soldered the IC to the board
Thanks for your help!
Hi, usually it's always a bad connection to the pins.
@@Gadomaitis I tried everything for hours. Then found out that my ch341 has the 3.3 . 5V problem. I fixed that but I can't read the chip. Maybe I broke the chip with the 5v
@@stefankefer8384 Honestly, I wouldn't even think about this kind of a solution. I saw that you can place a jumper for 5V, but it's needed rarely( personally never used it) and CH341 comes from the suppliers prepared for 3V.
@@Gadomaitis Hi, the CH341 Works now with Chips i bought new. With the Immo Chip it don't work. I think it's broken due to the 5V before.
Do you have a file that I can write on a new Chip so the ECU is working again.
Thank you!
@@stefankefer8384 Hi, text me on messenger. I have it, you can try.
hey,can you do that on my chryler crossfire??? immo off
Hey, I have checked the list, and there was no Chrysler there.
Мой блок EDC 15V-5.29 (038906018p) не могу найти калькулятор для иммо оф, такой как у автора не подходит, поделитесь чем можно сделать.
Not possible, it must work on this ECU. Do you do everything correctly? You can switch it off manually inserting 60 in that exact location. You can find it in this video. ruclips.net/video/qZ49hE5sHd4/видео.htmlsi=GEp8CiJCQ31FeWjy&t=226
What the Name this program
Hello! when I read the eeprom everything is always 00000. I've also tried a me 3.8, it's always the same. everything is zero. but he says the eeprom was recognized! only he reads nothing. Tried an EDC15P+ twice. with both he reads the eeprom! only not with all MSA and so on. everything is always 0
Please help me
Hi, it must be bad connection or wrong polarity of first pin. Or have you picked the right component to read from the list? I mean does it really matches what you pick and what you want to read? Have you desoldered EPROM?
Hello and thank you for your answer! I used a SOP8 clip. I used it to read 2 EDC15P+ Eproms without any problems (only for testing). Then I tried a Bosch ME 3.8 and everything 0000 is displayed here. Next was an EDC15V, here also everything 0000. Then another Bosch ME 7.3 and here everything is 0000. Then I connected the EDC15P+ again and everything works. I just do not understand. Today I will unsolder the eprom and try if they are then read out.
Iš it everywhere 24c02 EPROM?
@@Gadomaitis Yes I'm sure. My EDC15V is exactly the same as in your video. I did everything exactly like you, but it doesn't work. everything up to 0000.
@@Gadomaitis My chip doesn't say 24C02. There are other numbers on it. But he's in the same place.
Sir can ask some questions what software immo sir use?
Immo of software
@@Gadomaitis sir where you can immo software ? I need immo software
@@johnnychang7082 sir, have you tried Google it?
@@Gadomaitis already try…sir your software can off immo asia car ?
I don't know actually.
Hi, when I click read IC i only get 00 00 00 00 00 00 on everything what have i done wrong?
Hi, maybe bad connection of the clip to legs. I think there is an option to see the voltages on every leg.
@@Gadomaitis ok how do i check the voltage?
@@mubert4676 check in the application, which you are using to program the eeprom, there should be such thing as "check connection" or something like that. Did you choose the right eeprom to program from the list? Another thing, 1st leg must be the right one, important part not to miss it, otherwise you can get 00.
@@Gadomaitis yes I Choose the _24c02 and using asprogramer and cant find and check connection.
You are still struggling? Maybe try cleaning the eeprom pins and multiple times re-clamp it. Or try desoldering and then read it.
Hallo wie lese ich den EEprom B58253 aus?
Es ist ein Audi A4 AFN
MSTG : 038906018S
Ich habe den CH341A Reader.
Hi, you need to choose 24C02 eeprom for the list.
Do you have a link or info where to get the software?
Mhhauto has it, rutorents also.
@@Gadomaitis got a link to any of those people?
It's not people, it's webpage. Google it
My AFN engine came with a 68 pin ECU. will this work?
Might, might not, depends where immo is stored. I was trying to do one of the them, couldn't find that eeprom. Maybe my lack of knowledge.
What is this red cable u unplug from your CH341 programmer?
Becaus i tried your way But if i connect the clamp to the Chip my CH341 programmer Turns off because of lack of Power i dont know?
at what minute exactly you can see red cable? Mine used to switch off because of a week soldering. I have resoldered USB conections.
@ 2:27 u unplug a red cabel
@@istealvideos7834 I see, it's a cable tie, just to lift the programmer, as it had no communication. Later that day I have resoldered USB pins to PCB, and since then, no need of a such mod
Yeah i See they dont work good on those programmer my Test Clip was missing 2 Pins they were Not solder Right.
I Fix the Clip now it Work linke it should thx for the help
@@istealvideos7834 Glad to hear, cheers, G!!
👌👌👌👌
👀
Try to program a 95P08, and see if you can, I say no!
Thanks.
Works with 93c66 ?
Yes, you need to supply 5VDC for 93xxx EEPROM with jumper and insert into 25xxx socket
With electronics, Usually things doesn't go so well as planned
its out of focus
Sorry for inconveniec and thanks for your feedback. It happens when doing everything all by my self. Make sure to select 1020 HD video quality and NOT auto 1020 HD, sometimes it makes the difference.