LoRa Arduino Project to control Relay with feedback | Lora Tutorial 2023
HTML-код
- Опубликовано: 14 окт 2024
- In this Arduino project, I have shown how to make the Lora project using Arduino to control relay with real-time feedback using the RYLR896 Lora module. Explained both the transmitter and receiving LoRa circuit and source codes for the Arduino UNO and how to configure the LoRa modules with AT commands.
Get a free trial of the world's most trusted PCB design software, Altium Designer with 365 and 25% off your purchase: www.altium.com...
Free search engine for the best quality components from Octopart: www.octopart.com
I have covered the following topic in this Arduino Lora project:
00:33 Quick demo on the Arduino Lora project.
03:43 Explained Transmitter Lora circuit using Arduino Nano.
04:12 Explained Receiving circuit using Lora Arduino UNO
04:43 Explained source codes for Arduino Lora project
09:05 Control high voltage appliance with LoRa Module
Required components for the Transmitter Lora circuit:
1. Lora Module REYAX RYLR896 1no
2. Arduino Nano 1no
3. 220R Resistor (1/4w) 1no
4. 4.7k Resistor (1/4w) 1no
5. 10k Resistor (1/4w) 1no
6. 5-mm LED 1no
7. 0.96" OLED Display
8. Push buttons 2no
Required components for the Receiver Lora circuit:
1. Lora Module REYAX RYLR896 1no
2. Arduino UNO 1no
3. 5v 1-channel Relay Module (Active LOW) 1no
4. 220R Resistor (1/4w) 1no
5. 4.7k Resistor (1/4w) 1no
6. 10k Resistor (1/4w) 1no
7. 5-mm LED 1no
8. Push Buttons 1no
Amazon India Affiliate links:
REYAX RYLR896 Lora Module: amzn.to/3od1cFp
Arduino Nano: amzn.to/3Mxcgqi
Arduino UNO: amzn.to/35nNQwI
4-channel 5V Relay Module: amzn.to/2BQ5Y3o
OLED Display: amzn.to/3JJnVOV
Amazon United States Affiliate links:
REYAX RYLR896 Lora Module: amzn.to/3WapqN4
Arduino Nano: amzn.to/3ohjjdf
Arduino UNO: amzn.to/3Dmz5Xr
4-channel 5V Relay Module: amzn.to/3r2HuJ4
OLED Display: amzn.to/3uC2Orr
Help my projects on Patreon: / techstudycell
Feel free to donate any amount: paypal.me/sdaspay
Download Code for this Arduino LoRa project
iotcircuithub....
Important Links:
Previous Lora Tutorial video: • How to use LoRa with A...
Important points:
1. The Network ID and BAND should be the same for the transmitter and receiving end Lora module.
2. Set the BAND as per the eligible LoRa band in your country.
3. You can use any other microcontroller for this Lora project.
4. All the AT commands for configuring the LoRa module are written in the void setup() function of the source code.
5. The range for the LoRa project will be within 5KM in rural areas. (Range will decrease if the number of obstacles increases in the signal path).
6. After the restart you have to wait till the STATUS LED turns OFF.
7. You can also connect a 30A relay to control a pump using Lora Arduino UNO.
8. If you use any other Lora module, then configure the module in setup() as per the datasheet.
9. Please watch the complete video, otherwise you may face some issues.
**Please take proper safety precautions while working with high voltages.
During this Lora tutorial video, I have explained all the required information to make this LoRa project using Arduino. You can use any other microcontrollers with the LoRa module. Both the microcontroller and LoRa module communicate through the serial terminal at the 3.3V logic level.
The range for this LoRa module is up to 5KM, So this project is very useful in rural are where WiFi is not available. The range may decrease in urban areas due to more obstacles in the path.
#lora #arduino #arduinoproject
-----------
Thanks For Watching...
✅ SUBSCRIBE ✅LIKE ✅SHARE ✅ COMMENTS
Find out more such projects: iotcircuithub....
Facebook: / techstudycell
Instagram: / techstudycell
Telegram: t.me/techstudy...
-----------
-----------
WARNING:
This video is for demonstration and educational purposes only.
Each demonstration presents risks and hazards that must be fully understood before attempting.
And should be performed only by professionals
-----------
Other useful IoT projects:
Latest ESP32 projects playlist:
• ESP32 Projects
Latest NodeMCU projects playlist:
• NodeMCU Projects
Arduino Home Automation Projects playlist:
• Arduino Projects
Very good an clear explanation. Thanks
Good job! However, there’s just one thing that needs to be corrected. The 4.7 K ohm resistor should not be placed there. Instead, it should be connected between the Arduino and the combination of the LoRa Rx and the 10K ohm resistor. The LoRa should be connected to both the 4.7 K ohm and 10 K ohm resistors. Furthermore, the 10 K ohm resistor should be connected between the LoRa Rx and the GND.
Brilliant 👍
NIce job and thank you. Instead of using momentary switches is there a way to use SPST switches instead?
very good usefull , i am using her pcb from last 1year .
Thanks,I am also interested in this kind of project.
Thankyou. Could you please make similar project for Water tank level monitor and controll switch on and off as per level.
Very good; subscribed from Brazil
By using which software did you draw the circuit diagram?
Bro please make video using lora controlling water pump for farmer... Please
Good idea 👍💡
You can use this same project to control water pump. Please watch complete video
But some modifications required bro like electricity supply is there or not will show in remote and voltage and current parameters will show in remote display like this bro
What is the cost of full set...sir
@@TechStudyCell Not working for me, no response to AT command when passed through SoftwareSerial of Arduino Nano😭
Can you please provide program code of this project
Can I use Sx1278 lora module instead of this?
pls advise.thanks
I think you should try smart bike controller project ones
Can this be set up to be AAA battery powered ?
Please make for SX1278 ra-02
Sir please make a vedio with rylr998
Did you get 5KM Range
LORA based IOTs, required in agriculture field enormously !!!!. Pls work on it.Thanks
Has anyone actually got this to work? I followed it to the letter and nothing happened. I took it to a professional and there were many errors in the code, mismatched baud rates, and the REYAX of the transmitter is not grounded except through the switches or LED resistor- it has only 0.3v supply!. The voltage dividers are wired wrong the LoRa Rx goes between the resistors not in series. Mine would never have worked and still doesn't, I have not got to the bottom of all the bugs yet. I have wasted many hours on this misinformation. If anyone can get this to work please let me know as I have a use for these and they are exactly what I want so I would like it to work..
Nice video cost of project
Bro .. please make manually real time and timer relay on and off
Hi sir .lora module India me kaha se ordar kare .
Koy website hoto batavana please
Use lora ra 02 sir which is cheaper
Hello
Blynk Lora vibration sensor alarm for car remote on/off buzzer sound alert
Is this module legal in India and this frequency
Yes. I have used 865mhz
Why it's take delay after pressing button of transmitter side
😮
Whats the range
Bhai asa ak circuit banao Jo bijli Jane par mobile par sms a Jaye or bijli Ane par sms a Jaye..
I am 1st
👍
I have a project idea can you implement it
Its the monitoring and controlling the temperature, humidity,light intensity water level and ammonia and carbon dioxide gas in poultry farm. By using esp32 board , dht11 sensor, LDR sensor, MQ-135 and MQ-5 sensor. Then we have to send the data to firebase. And from firebase to mobile, and there shold be a logic if click to torn on fan or light 🚨 by clicking button from mobile app
Reply me if you are going to do it
I hate arduinoprojects.