Hi Søren, just for your info here regarding the motor on your model of Miele. You have a brushed motor which is controlled by the electronic pulsing DC current which controls the speed. Faster the pulses, faster the motor runs. Also when removing the front panel, you don’t need to remove those screws on the top behind that top fascia. Once you have the door seal retaining spring clip off, removed the two screws holding the door lock on, removed the screws on the bottom left and bottom right of the front panel and the large screw at 6 O’ Clock below the door seal, pull the bottom of the front panel towards you and the top of the panel will release from two plastic ‘pins’ and drop down. The panel is now released and can be removed and set aside. Also to make the door lock work with the front off, the manual door release is designed to fit into the door lock and making it work. It’s the round part which usually sits behind the filter housing door, that part fits in the door lock once you have the front panel removed. Regarding your motor not running, when you unplugged the edge clip electrical plugs, you would have for sure cleaned up a dirty connection. Also cleaning off any dirt would have solved the issue as well. Very small data voltages go back and forwards and it doesn’t take much to stop the machine from working. Well done indeed. Hope that helps. 👍🏻
5:10 - "position 4 ... uh... some sort of American function." Doesn't seem to do anything that makes sense. European humour! Love it! Thanks for the vid, Soren. I'm looking at a similar problem for my W4800 and it builds confidence to see someone else's foray into the guts of a cousin unit. That little bit of debris you mentioned which seemed to be astride a couple of the traces leading to that fancy green chip was likely the problem. Even a slight short could have influenced the voltage levels in those signalling lines enough to prevent the activation of a relay somewhere else in the machine. A good tidy and cleanout never hurts (unless done without being careful.)
Thanks for your comment. I agree but the debreis has not occoured while disassembled... I tend to think the electronics was reset during my complete disassembly of the PCB.
The circuit board was himself shorten out by contacting with the frame of the machine, or with other metal parts or cables near by or beneath. Or humidity or rust make the same with nearby parts of the board - especially valid for capacitors. If you saw on your video, 2:09 - 2:17, on the right front part of the machine, beneath the decorative white strip, there was a plenitude of rust.
Thanks for your commen .I cannot tell but the rust did no occur while I was changing bearring (1 day) and it worked before. But somehow detaching all wires reset the PCB.
I have a Meile model 1714 its 13 yrs old but suddenly stopped working when i had started a wash. I heard a ' clunk' and from then on there was no display and the machine would not switch on . any common probs with these machines that you know of that might cause these symptoms.
hi i have one miele washing machine model pw6055 plus power supply from the socket switch,but the on off switch when i on the power switch no working at all,can give me more information what's the problem faultty,thanks
Yeah. Miele acts like their info is top secret. If you are not an authorized repair person they will give you nothing. Germans with those Nazi attitudes.
Hi Bob. Yes still working perfect. Grease the rubber sealing so it dosn't run dry. I imagined that water would be lubricant enough. It is ok today but we had som squeeking :-)
Codes are not guaranteed to be the same across all Miele machines, but this is what the technical manual says for my machine, so it may be something to look at on your machine. I don't work for Miele, so unfortunately I can't help you beyond quoting what the manual for my machine says... *Fault code F53, tachogenerator:* *Symptom* In normal operation the display shows *Technical fault*. The drum or drive is blocked. The motor does not start or is switched off after 1.5 s. An attempt is made to start the motor during two reversing phases. In the spin cycle the program is interrupted immediately. The drive may possibly function again after a cooling period. The solenoid valve is closed and the drum pump is activated for 120 s. *Cause* Tachogenerator defective. The tachogenerator is not supplying any meaningful AC voltage to the power-programme module (ELP) *Check tachogenerator* (wrench icon) Check the tachogenerator, see Drive failure 070 3.1 *Cause* Drive defective. Via the tachogenerator the power-programme module (ELP) has detected a major discrepancy between the desired drive speed and the actual drive speed. *Remedy* (wrench icon) Check the drive, see Drive failure 070 3.1
Hello Muhammad. Thanks for your question.My conclusion is that I could not detect any faults. Every part worked ok, but the motor would not run. I switched off electricity several times with no result. After taking out the PCB it somehow resat it self and the machine worked again :-) I believe that it some electronics in the PCB that needed to be isolated to reset....Br Søren
@@srenmadsen4885 ola amigo como esta eu tenho uma mieele modelo w837 ela liga entra água e quando ela vai começa a lavar ela pisca o LED e não roda o motor e a bomba entra e joga a água fora sera que o amigo poderia mim ajudar meu e-mail e robertobisporj@hotmail.com
You should never apologise for your English, it is excellent.
Hi Søren, just for your info here regarding the motor on your model of Miele. You have a brushed motor which is controlled by the electronic pulsing DC current which controls the speed. Faster the pulses, faster the motor runs. Also when removing the front panel, you don’t need to remove those screws on the top behind that top fascia. Once you have the door seal retaining spring clip off, removed the two screws holding the door lock on, removed the screws on the bottom left and bottom right of the front panel and the large screw at 6 O’ Clock below the door seal, pull the bottom of the front panel towards you and the top of the panel will release from two plastic ‘pins’ and drop down. The panel is now released and can be removed and set aside.
Also to make the door lock work with the front off, the manual door release is designed to fit into the door lock and making it work. It’s the round part which usually sits behind the filter housing door, that part fits in the door lock once you have the front panel removed. Regarding your motor not running, when you unplugged the edge clip electrical plugs, you would have for sure cleaned up a dirty connection. Also cleaning off any dirt would have solved the issue as well. Very small data voltages go back and forwards and it doesn’t take much to stop the machine from working. Well done indeed. Hope that helps. 👍🏻
Hi. Thanks for your comment sharing that detail :-)Br Søren
Thank you for the info regarding the removing the front without removing control panel.
5:10 - "position 4 ... uh... some sort of American function." Doesn't seem to do anything that makes sense. European humour! Love it!
Thanks for the vid, Soren. I'm looking at a similar problem for my W4800 and it builds confidence to see someone else's foray into the guts of a cousin unit.
That little bit of debris you mentioned which seemed to be astride a couple of the traces leading to that fancy green chip was likely the problem. Even a slight short could have influenced the voltage levels in those signalling lines enough to prevent the activation of a relay somewhere else in the machine. A good tidy and cleanout never hurts (unless done without being careful.)
Thanks for your comment. I agree but the debreis has not occoured while disassembled... I tend to think the electronics was reset during my complete disassembly of the PCB.
Thank you for the video. Your English is great by the way
kas m I agree Your English is brilliant
Thanks :-) and thanks for your feedback. It is important that we share our finding :-)
Very informative video. thanks for taking the time to make this video
Thank You for your comment. Searching for the fault I summarized a lot of good points that I felt good to share with other Do it your self people :-)
Thanks :-)
The circuit board was himself shorten out by contacting with the frame of the machine, or with other metal parts or cables near by or beneath. Or humidity or rust make the same with nearby parts of the board - especially valid for capacitors. If you saw on your video, 2:09 - 2:17, on the right front part of the machine, beneath the decorative white strip, there was a plenitude of rust.
Thanks for your commen .I cannot tell but the rust did no occur while I was changing bearring (1 day) and it worked before. But somehow detaching all wires reset the PCB.
Video very good.. Thanks
Thanks Gianluigi
Great Video, thank you !
I have a Meile model 1714 its 13 yrs old but suddenly stopped working when i had started a wash. I heard a ' clunk' and from then on there was no display and the machine would not switch on . any common probs with these machines that you know of that might cause these symptoms.
Thank you! Helped me alot! Cheers.
I am happy to hear that :-)
So, what is the error in this case? What is the solution?
hi i have one miele washing machine model pw6055 plus power supply from the socket switch,but the on off switch when i on the power switch no working at all,can give me more information what's the problem faultty,thanks
Help
I have a miele 5985 f 53 failure.
Mother board already replace so Is the tacometer.
What can it be
Thanks a lot
I have a miele paragon it’s really hard to find any information about my machine
Yeah. Miele acts like their info is top secret. If you are not an authorized repair person they will give you nothing. Germans with those Nazi attitudes.
@@theblade9024 not miele in sweden
@@lars-akeholmberg7190 its germen
10:47 your second blue cap is starting bulging... or my optical illusion?
Hi. I think that is an optical illusion ;-)
Hi S/oren, is your washing machine still working? As for now, I have to troubleshoot my Miele... :/
Hi Bob. Yes still working perfect. Grease the rubber sealing so it dosn't run dry. I imagined that water would be lubricant enough. It is ok today but we had som squeeking :-)
I have a code F53, it’s telling me to call for service. Do you know what’s wrong with it?
Sorry David. Have not seen that type og message.
Codes are not guaranteed to be the same across all Miele machines, but this is what the technical manual says for my machine, so it may be something to look at on your machine. I don't work for Miele, so unfortunately I can't help you beyond quoting what the manual for my machine says...
*Fault code F53, tachogenerator:*
*Symptom*
In normal operation the display shows *Technical fault*.
The drum or drive is blocked. The motor does not start or is switched off after 1.5 s.
An attempt is made to start the motor during two reversing phases.
In the spin cycle the program is interrupted immediately.
The drive may possibly function again after a cooling period.
The solenoid valve is closed and the drum pump is activated for 120 s.
*Cause*
Tachogenerator defective.
The tachogenerator is not supplying any meaningful AC voltage to the power-programme module (ELP)
*Check tachogenerator*
(wrench icon) Check the tachogenerator, see Drive failure 070 3.1
*Cause*
Drive defective.
Via the tachogenerator the power-programme module (ELP) has detected a major discrepancy between the desired drive speed and the actual drive speed.
*Remedy*
(wrench icon) Check the drive, see Drive failure 070 3.1
Hi mr i have meile mvb120 there is a problem when push start its says work not possible plz what the problem
Sorry I cannot help you.
So Sir your video summary is pcb connections problem? Or connector? Or other parts would you please give in details it helps us lot. Thank you.
Hello Muhammad. Thanks for your question.My conclusion is that I could not detect any faults. Every part worked ok, but the motor would not run. I switched off electricity several times with no result. After taking out the PCB it somehow resat it self and the machine worked again :-) I believe that it some electronics in the PCB that needed to be isolated to reset....Br Søren
@@srenmadsen4885 ola amigo como esta eu tenho uma mieele modelo w837 ela liga entra água e quando ela vai começa a lavar ela pisca o LED e não roda o motor e a bomba entra e joga a água fora sera que o amigo poderia mim ajudar meu e-mail e robertobisporj@hotmail.com
Lol you skipped the most important part.
Another 10 minutes wasted, you could have said that in the first 10 seconds.
Are you married ?
6:16 ... Oh, I hear you say you have a wife. Thanks for nothing.
Ha ha :-) Yes
SilentPoliceman He does have nice legs 😁😁