theyardsalellc6092, That's so thoughtful of you! I'm sure Garrett appreciates the support and recognition for the hard work he puts into sharing information.
Thank you, Garrett. I continue to learn better CNC practices from your videos. If possible, there is an issue I'd like to see you address (I suspect many others may be interested in this issue, also). I am running an Axiom Iconic 6 (1HP spindle). Overall, the router runs fine, and performs well in all tasks, regardless of the type of wood, toolpath, or particular bit. However, the one issue I cannot seem to resolve is NOISE, especially when running 1/4 inch end mills (carbide, up or downcut, or compression bits) on domestic or exotic hardwoods. When I put the IDC Hog in the router, it's so loud the neighbors give me a look. The only information I can find generally follows the addage: "A screaming bit is a hungry bit." I have varied the speed, feed rate, and depth of cut, but the noise generated is still enough to drive me out of the garage. My wife is refusing to make my favorite fried chicken and roasted potatoes dinner until I "...figure out how to run that machine a lot quieter!" Garrett, can you help??
JayTombaugh, I'm glad to hear you're enjoying the videos and getting better with your CNC practices! Noise can definitely be a challenging issue with CNC machines, especially when using specific bits like the IDC Hog. It might be worth experimenting with different speeds and feed rates beyond the typical recommendations since different materials and setups can react uniquely. Additionally, ensuring that your machine is well-tuned and that the bit is properly secured can sometimes help reduce vibrations and, consequently, noise. Best of luck, and I hope you can solve the noise problem and get back to your favorite dinner soon!
I followed and IDC email link to this video and even though I had just adjusted an Aspire model using the resize function I learned more because of the details you included in the video. Thank you. One related thing that I seem to have learned on my model resizing effort was that the finished resized model needs to be copied to the other side when doing a two-sided design in order to have both sides carved at the same thickness. This must be done after the initial resizing or else the model, if started fresh on side two will not match side 1 model’s thickness. I expect if you were to cover this functionality you would also explain other things about the exercise that would help me understand it all better.🎉
arthurpetch2874, I'm really glad you found the video helpful and that it deepened your understanding of the resizing function! Your observation about needing to copy the resized model for two-sided designs is spot on; it's a crucial detail for achieving consistent carvings. It's great to hear you're diving into those specifics, as they really make a difference in the final result. Happy woodworking!
Hi Garrett I am having trouble scaling a job in Aspire ! I want to carve a 1/2 pear shape into some hardwood (Hollow out ) . But I want to scale it so it can be deeper on one side compared to the other and Having a sharper radius on one side to the other . Plus adding a 1/4 “ rounded lip On the profile edge ! Size is 16” X 8 “ X 3 “ Need to leave 3/4 or 1 “ flat depth . I can only manage to get it Symmetrical on both sides ! I am practicing on a block of polystyrene for speed and ease to see the outcome ! Just roughing with a 1/4 four flute end mill at this Stage ! Hope you can find some clarity for me , and help someone else in a similar Situation ! Keep up the Great work ! 🤗 From Down Under 🦘 Cheers Andy
andrewmcallister9250, Hi Andy! It sounds like you're working on an interesting project with that pear shape. To achieve the asymmetrical design in Aspire, you might want to adjust the scale and rotation settings for your model after you've created it, allowing you to stretch certain dimensions differently. You can also utilize the sculpting tools in Aspire to refine the shape and create varying depths. Experimenting with the heights and contours in your design should help you achieve the desired outcome. Good luck with your practice on the polystyrene! Cheers!
Thank you for this video I learned a lut from it. Garrett, I'm having a problem with my CNC and that is; when I connect my computer to the CNC and download the G code as soon I press the enter the Z motor goes up for more than a minute, and I have to disconnect the motor and stops making noise, what can I do to prevent this. I really appreciate your help , thanks again
Mr5AO, I'm glad you found the video helpful and thanks for the support! While I don't have a specific video on thread milling right now, I appreciate your interest!
What percentage do we need to add to an item, such as cutting a 1” hole to fit a 1” part. I run into this much of the time, both on the Camaster CNC and on the plasma table. A couple of days back I needed to cut a hole in a 3/16” plate to fit a ¾” pipe which Is just under 1.1” O.D. I use CorelDRAW for drawing parts for plasma and Vcarve V 12.5 for the CNC. I have the same issue on both machines. The holes are nearly always too small. I do know to cut inside the circle.
moccasin, When cutting a hole to fit a part, it's often useful to account for the kerf of the cutting tool, which is the material removed during the cut. This can vary based on the tool and the cutting method. For routing and CNC machining, you might add around 0.01” to 0.05” to your diameter, but testing will help you find the best fit for your specific setup. Additionally, when using the plasma cutter, keep in mind that it tends to create a larger hole due to the heat and the nature of the cut. Regular calibration and some trial cuts can greatly improve your accuracy.
GET THE LIGHTNING DRILL for CRIB BOARDS → idcwoodcraft.com/search?q=drill
Thank you Garret, you explain things clearly and slow! Really appreciate it
rich_wood_resin_works, I'm glad you found the explanations helpful! Thank you for your kind words!
Everyone should buy Garrett a cup or two of coffee for all of this free information.... I did.
theyardsalellc6092, That's so thoughtful of you! I'm sure Garrett appreciates the support and recognition for the hard work he puts into sharing information.
Another great video Garrett!!! Thank you again for doing these videos and making them available to the community.
alfredforbrich4836, I'm really glad you enjoyed the video! It's great to share and connect with everyone in the community.
Thank you Garrett for your teaching on cnc 🎉🎉🎉🎉🎉
RAcreativewoodworks, You're very welcome! I'm glad you found it helpful.
You are a gem Garrett.
Horizon-m5o, Thank you so much! I appreciate your kind words.
Well done Garrett.
RobSandstromDesigns, Thank you! I appreciate your kind words!
Thanks so much for this video, Garrett!!! This is going to help so many people who get files like that.
Great seeing your tutorials, as always. 😃👍
JoeLazzara, You're very welcome! I'm glad you found the video helpful.
Thanks, very good to know
larrymckelvey1794, You're welcome! I'm glad you found it helpful.
Thanks Garrett
I like your new Diggs can wait to see it in person🤯
Hi Larry. Thanks! Yep, people can come to visit
Great simple explanations Garrett - thank you!
CKenBowser, You're very welcome! I'm glad you found the explanations helpful!
Thank you, Garrett. I continue to learn better CNC practices from your videos.
If possible, there is an issue I'd like to see you address (I suspect many others may be interested in this issue, also). I am running an Axiom Iconic 6 (1HP spindle). Overall, the router runs fine, and performs well in all tasks, regardless of the type of wood, toolpath, or particular bit. However, the one issue I cannot seem to resolve is NOISE, especially when running 1/4 inch end mills (carbide, up or downcut, or compression bits) on domestic or exotic hardwoods. When I put the IDC Hog in the router, it's so loud the neighbors give me a look. The only information I can find generally follows the addage: "A screaming bit is a hungry bit." I have varied the speed, feed rate, and depth of cut, but the noise generated is still enough to drive me out of the garage. My wife is refusing to make my favorite fried chicken and roasted potatoes dinner until I "...figure out how to run that machine a lot quieter!" Garrett, can you help??
JayTombaugh, I'm glad to hear you're enjoying the videos and getting better with your CNC practices! Noise can definitely be a challenging issue with CNC machines, especially when using specific bits like the IDC Hog. It might be worth experimenting with different speeds and feed rates beyond the typical recommendations since different materials and setups can react uniquely. Additionally, ensuring that your machine is well-tuned and that the bit is properly secured can sometimes help reduce vibrations and, consequently, noise. Best of luck, and I hope you can solve the noise problem and get back to your favorite dinner soon!
Thanks Garrett
GaryBailey-nq6wv, You're welcome! I'm glad you enjoyed it!
I followed and IDC email link to this video and even though I had just adjusted an Aspire model using the resize function I learned more because of the details you included in the video. Thank you.
One related thing that I seem to have learned on my model resizing effort was that the finished resized model needs to be copied to the other side when doing a two-sided design in order to have both sides carved at the same thickness. This must be done after the initial resizing or else the model, if started fresh on side two will not match side 1 model’s thickness.
I expect if you were to cover this functionality you would also explain other things about the exercise that would help me understand it all better.🎉
arthurpetch2874, I'm really glad you found the video helpful and that it deepened your understanding of the resizing function! Your observation about needing to copy the resized model for two-sided designs is spot on; it's a crucial detail for achieving consistent carvings. It's great to hear you're diving into those specifics, as they really make a difference in the final result. Happy woodworking!
Thanks for the great videos you make.😄
roberthenrich8105, I really appreciate your kind words! I'm glad you're enjoying the videos.
Hi Garrett
I am having trouble scaling a job in Aspire !
I want to carve a 1/2 pear shape into some hardwood (Hollow out ) .
But I want to scale it so it can be deeper on one side compared to the other and
Having a sharper radius on one side to the other . Plus adding a 1/4 “ rounded lip
On the profile edge !
Size is 16” X 8 “ X 3 “ Need to leave 3/4 or 1 “ flat depth .
I can only manage to get it Symmetrical on both sides ! I am practicing on a block of polystyrene for speed
and ease to see the outcome ! Just roughing with a 1/4 four flute end mill at this
Stage ! Hope you can find some clarity for me , and help someone else in a similar
Situation !
Keep up the Great work ! 🤗
From Down Under 🦘
Cheers
Andy
andrewmcallister9250, Hi Andy! It sounds like you're working on an interesting project with that pear shape. To achieve the asymmetrical design in Aspire, you might want to adjust the scale and rotation settings for your model after you've created it, allowing you to stretch certain dimensions differently. You can also utilize the sculpting tools in Aspire to refine the shape and create varying depths. Experimenting with the heights and contours in your design should help you achieve the desired outcome. Good luck with your practice on the polystyrene! Cheers!
Thanks for the help
nancej100, You're very welcome! I'm glad you found it helpful.
Thank you for this video I learned a lut from it. Garrett, I'm having a problem with my CNC and that is; when I connect my computer to the CNC and download the G code as soon I press the enter the Z motor goes up for more than a minute, and I have to disconnect the motor and stops making noise, what can I do to prevent this.
I really appreciate your help
, thanks again
This is probably something to ask the company that sold you the machine
Thank you, Garrett!
Do you have any videos on thread milling?
Mr5AO, I'm glad you found the video helpful and thanks for the support! While I don't have a specific video on thread milling right now, I appreciate your interest!
Great Video! I've used this tool, but not nearly to the extent you've shown here.
MSManuel-61, I'm glad you enjoyed the video! It's amazing how much you can explore with tools once you dive in.
Thank You
GuyBeaver-h3q, You're welcome! I'm glad you enjoyed the video.
Thanks!
larrysmith3935, You're welcome! I'm glad you enjoyed it!
What percentage do we need to add to an item, such as cutting a 1” hole to fit a 1” part. I run into this much of the time, both on the Camaster CNC and on the plasma table. A couple of days back I needed to cut a hole in a 3/16” plate to fit a ¾” pipe which Is just under 1.1” O.D. I use CorelDRAW for drawing parts for plasma and Vcarve V 12.5 for the CNC. I have the same issue on both machines. The holes are nearly always too small. I do know to cut inside the circle.
moccasin, When cutting a hole to fit a part, it's often useful to account for the kerf of the cutting tool, which is the material removed during the cut. This can vary based on the tool and the cutting method. For routing and CNC machining, you might add around 0.01” to 0.05” to your diameter, but testing will help you find the best fit for your specific setup. Additionally, when using the plasma cutter, keep in mind that it tends to create a larger hole due to the heat and the nature of the cut. Regular calibration and some trial cuts can greatly improve your accuracy.
I don't see any bits with the name lightning ??
Sorry for not making it clearer. Here's the link
idcwoodcraft.com/search?q=drill
Thanks!
theyardsalellc6092, thanks for the support brother!