Thank you so much for the compliment! I’m trying to make them that way as I’ve noticed myself when watching other videos that I tend to lose interest or fast forward if it’s too long 😅
No, because a blow dryer blows air and a heat gun emits heat. It is the heat that releases the bubbles. You could use a bakers torch or a lighter to use the heat from the flame to release those bubble but you need to be careful not to ruin your mould or scorch your resin
Bonjour de France, Super beau . Ma question, moi qui débute Je voudrais savoir quelques renseignement. Quel papier utilisez vous pour faire des dessins dans vos moules ? Et autre chose, il faut attendre combien de temps pour l’enlever ? Merci de me répondre en traduction si possible ? 🙏😘😘😘
In this video I used Saran wrap and I waited 24 hours to remove it:) 68 / 5,000 Translation results Translation result Dans cette vidéo j'ai utilisé du Saran wrap et j'ai attendu 24h pour l'enlever :)
No it has to be done while it’s still wet and uncured so that you can manipulate the Saran Wrap to get the wrinkles. I do it after about 30 ish minutes after pouring after making sure to remove the bubbles that have risen to the surface😊
These are gorgeous. I always have trouble removing the plastic film. Yours seem to peel away very easily. Do you have any tips? Have you ever tried using silicone release spray on the plastic. 😊
I wish I had tips to share. The only times I’ve had trouble is if I bury some within the resin trapping it. Perhaps it’s the brand? Mine is glad cling wrap.
Hmmm, the only time I had my plastic get stuck was when it had folded on itself. I just continuing with the next step adding the micas and you can barely tell where the Saran Wrap got stuck. I don’t know of any other tricks to get it to release, I would keep going.
Im trying this technique,will be removing the cling wrap tonight😁.I was wondering if i can paint the coaster with acrylic paint instead of using the mica powder? 🤔
I love how fast this video was. Very informative, but to the point so I didn't have to waste 40 minutes.
I subscribed. ❤
Thank you so much for the compliment! I’m trying to make them that way as I’ve noticed myself when watching other videos that I tend to lose interest or fast forward if it’s too long 😅
I'm about to try right now😮😁
Have fun! 💕
@@ArtsyIslandGirl I don't think it's going so well but we will see if I can get the wrap off in the morning
So beautiful can’t wait to try it.
Thank you💕. I hope you enjoy making them when you try it out yourself!
You make it look so easy! Look at you go. Good for you!
It really is pretty easy!
These are really beautiful 😻
Thank- you! I really enjoyed making them 🥰
So beautiful. I am in love.
Thank-you🥰
Can I use dryer instead of heat gun ..
No, because a blow dryer blows air and a heat gun emits heat. It is the heat that releases the bubbles. You could use a bakers torch or a lighter to use the heat from the flame to release those bubble but you need to be careful not to ruin your mould or scorch your resin
Are you using normal poly bag or any specific sheet ?
I’m using glad cling wrap but I don’t believe it needs to be a particular type
@@ArtsyIslandGirl oh Thank you ☺️
@@tabassum- you’re welcome🥰
Bonjour de France,
Super beau .
Ma question, moi qui débute
Je voudrais savoir quelques renseignement.
Quel papier utilisez vous pour faire des dessins dans vos moules ?
Et autre chose, il faut attendre combien de temps pour l’enlever ?
Merci de me répondre en traduction si possible ?
🙏😘😘😘
In this video I used Saran wrap and I waited 24 hours to remove it:)
68 / 5,000
Translation results
Translation result
Dans cette vidéo j'ai utilisé du Saran wrap et j'ai attendu 24h pour l'enlever :)
Dans cette vidéo j'ai utilisé du Saran wrap et j'ai attendu 24h pour l'enlever :)
@@ArtsyIslandGirl
Merci de ta réponse 🙏😘
Before applying the saran wrap the resin poured should be completely dried or slightly wet...what the texture should be before applying the wrap?
No it has to be done while it’s still wet and uncured so that you can manipulate the Saran Wrap to get the wrinkles. I do it after about 30 ish minutes after pouring after making sure to remove the bubbles that have risen to the surface😊
These are gorgeous. I always have trouble removing the plastic film. Yours seem to peel away very easily. Do you have any tips? Have you ever tried using silicone release spray on the plastic. 😊
I wish I had tips to share. The only times I’ve had trouble is if I bury some within the resin trapping it. Perhaps it’s the brand? Mine is glad cling wrap.
@@ArtsyIslandGirl Yes that does seem to play a big part in the problem. Thanks anyway. 🥰 I will keep persevering😄
@@susanmurray7530 Good Luck and have fun playing!
The plastic wrap got stuck in my resin help 🥲
Hmmm, the only time I had my plastic get stuck was when it had folded on itself. I just continuing with the next step adding the micas and you can barely tell where the Saran Wrap got stuck. I don’t know of any other tricks to get it to release, I would keep going.
Im trying this technique,will be removing the cling wrap tonight😁.I was wondering if i can paint the coaster with acrylic paint instead of using the mica powder? 🤔