So how did you fix this? Currently out gate opens do not work. They only work when closing and if you pause it to try and send it back, itll just move towards close again. I did randomly fix this issue a couple month's ago but cannot remember how. I played around with open set stop close buttons
Buenas noches, tengo un Robus 350 y voy a perder la cabeza con las fotocelulas, he comprado una nueva Bluebus original porque la anterior no funcionaba, detectaba al intentar hacer el aprendizaje de longitud de la puerta y me para constantemente solo cuando la puerta comienza a movertse, pues con la nueva me pasa igual, he llegado a pensar que están mal situadas y lo que me detecta es la puerta en movimiento porque en parado no se queda la luz fija en RX, pero el resto de vecinos la tienen situada igual. El parpadeo de las dos fotocelulas es correcto una vez realizo el aprendizaje de dispositivos por lo que la señal es correcta. Si pudieras ayudarme te lo agradecería. Gracias de antemano
Benzer sorun bende ki nice robus 400 cihazımda da vardı. Flaşör sinyallerinden hatanın fotoselden kaynaklı olduğunu öğrendim. 2 adet fotoseli parçalarına ayırarak içinde yuvalanmış örümcek, böcek artıklarından, yuvalarından temizledim ve sorunum çözüldü. parçalarını tekrardan montajını yapıp fotoselin açık yerlerinden tekrardan böcek girmemezi içi fotoselin çerçevesini elektrik bantı ile izole ettim. (Flashing light signalling "2 flashes 1-sec pause 2 flashes. Cause: Intervention of a photocell)
@@martinly1050 You know there is a stick there on the Robus RB400 gate opener called Closing/Opening Limit Swith, when the gate moves to the end that stick will be pushed so the control board knows the gate reached to the end and stopped the motor. That stick (Closing/Opening limit swith) connected to two Omron Electronics V-16-1C26 switch. In my case, one of Omron V-16-1C26 switch is faulty, I took that faulty V-16-1C26 switch apart and cleanned it to make it working again. The whole repair cost nothing but four hours my spare time.
So how did you fix this?
Currently out gate opens do not work. They only work when closing and if you pause it to try and send it back, itll just move towards close again.
I did randomly fix this issue a couple month's ago but cannot remember how. I played around with open set stop close buttons
Buenas noches, tengo un Robus 350 y voy a perder la cabeza con las fotocelulas, he comprado una nueva Bluebus original porque la anterior no funcionaba, detectaba al intentar hacer el aprendizaje de longitud de la puerta y me para constantemente solo cuando la puerta comienza a movertse, pues con la nueva me pasa igual, he llegado a pensar que están mal situadas y lo que me detecta es la puerta en movimiento porque en parado no se queda la luz fija en RX, pero el resto de vecinos la tienen situada igual. El parpadeo de las dos fotocelulas es correcto una vez realizo el aprendizaje de dispositivos por lo que la señal es correcta. Si pudieras ayudarme te lo agradecería. Gracias de antemano
Benzer sorun bende ki nice robus 400 cihazımda da vardı. Flaşör sinyallerinden hatanın fotoselden kaynaklı olduğunu öğrendim. 2 adet fotoseli parçalarına ayırarak içinde yuvalanmış örümcek, böcek artıklarından, yuvalarından temizledim ve sorunum çözüldü. parçalarını tekrardan montajını yapıp fotoselin açık yerlerinden tekrardan böcek girmemezi içi fotoselin çerçevesini elektrik bantı ile izole ettim. (Flashing light signalling "2 flashes 1-sec pause 2 flashes. Cause: Intervention of a photocell)
El led de bluebus parapadea 7 veces eso indica falla en la tarjeta electrónica
Defect chip .. you need to replace it ..
Thanks, I have fixed it. It was caused by a faulty switch.
@@baikal888 (faulty switch) !!!
What is that?? Could you explain more
I have the same issue with mine. Which switch was faulty?
@@martinly1050 I had to buy a new board from ebay unfortunately and have fixed it .. no other way but to replace it.
@@martinly1050 You know there is a stick there on the Robus RB400 gate opener called Closing/Opening Limit Swith, when the gate moves to the end that stick will be pushed so the control board knows the gate reached to the end and stopped the motor. That stick (Closing/Opening limit swith) connected to two Omron Electronics V-16-1C26 switch. In my case, one of Omron V-16-1C26 switch is faulty, I took that faulty V-16-1C26 switch apart and cleanned it to make it working again. The whole repair cost nothing but four hours my spare time.
Schematic diagram of the circuit card. If you have contact me please.