Thanks Bob. I'm killing it at my new job with all of your expert advice stuck in my head. I'm 50 and still learning thanks to you sacrificing your time to share your knowledge. Much appreciated.
A little trick that will make that cutting edge slicker is run a piece of soapstone along the edge. Slicker than snail snot. Torch will glide right along and never try to drag.
Hi Bob, and thanks for another QUALITY training video. Our shop had a setting of 12/42 for everything. Of course we worked with heavy steel all the time and kept big tips on the torches. Here's a trick an old boiler-maker taught me, over 40 years ago, that works really well for cleaning your cutting tip, right before you start cutting. Get a rough-cut Oak 2x4 x 18" long. You can use that as a rest to keep the heat away from your hand...that and a C-clamp vice grip. Get your flame ready to cut. Squeeze the Oxy handle and place the face of the tip onto the face of the Oak board, and drag it to you...like 6" in 2 seconds fast. Then immediately put it to the metal, get the puddle and start your cut. You'll be amazed at the difference! He said the Oak carbon blows out the mill-scale and cleans your tip...HOT. Then it's ready to eat! I appreciate your videos! Please advise ALL your students to NEVER oil the threads on your bottle caps nor get oil anywhere around oxygen! It will blow up!Very dangerous! The 3 piece bottle caps are the way to go. Screw them on, hinge them closed and put the pin in the hole. When not using torch. That way, if for some reason the securement for the tank releases its hold on the tank, the valve will be protected! THANKS FOR POSTING
Hidy. Thanks for another wonderful video. You were speaking about tip cleaning...an old boilermaker taught me a kewl cleaning trick, back 40 years ago...take a rough-cut Oak 2x4x12" with you, everywhere you work. Most of the steel he would cut was 2" thick end sheets and 1" on snow-plows (which are modern day cow catchers), on the end of a Locomotive. He says...when your tip starts singing to ya, keep it lit and press the cut trigger and put the tip right on the face of thw wood and drag it along wit the tip touching the wood. The flames will force away...back up toward the torch. Rub the tip on the wood with the trigger pulled, for 4 or 5 three inch rubs and then pull it away from the wood. If the tip was full of scale, the oak will boil it out and the tip will be cleaner than if you ran a wire file into its ports and the end will be like a new tip! Needless to say, I keep a rough cut Oak 2" x 4" x 12" in my welding bay all the time, for tip cleaning. Try that one out
I always refer to the charts that come inside the Victor cutting torch manual .... It has travel speed and pressures listed. It's never let me down. Thanks for video.
Used a Oxy Ace for a couple of years. Probably have 500 hours on them. Mostly 1/4 to 1/2 plate. The very first thing you said, imho, was the most important. You have to keep the oxygen jet orifice "pristine" for good cuts.
Excellent video. I’m afraid the torch is under appreciated. I would love to see more videos on the torch. I learned more here about cutting to correct some of my errors. Keep up the good work and don’t gloss over the common knowledge some that really isn’t so common.
very good lesson, i needed that one, thanks, my oxygen regulator blew the fusible plug out for some reason when i cracked the valve open, it is a Victor set, scared me to death, the set has been used very little but they are several years old.. keep up the good work that you do for all of us, thanks again,,
Yep ! Always tell my helpers "PRE-HEAT, & PATIENCE ! PRE-HEAT, & PATIENCE !" You'll end up with a beautiful cut ! When they don't listen I tell them to clean up their own mess with the 7" grinder !! I also tell them "OLD AGE, AND TREACHERY WILL ALWAYS OVERCOME YOUTH, AND SKILL !!" 😁😁😁😁👍👍👍😉✌
Great Video Bob, Unless the camera is not showing it good I have been adjusting my torch wrong for 40 years. I have always open the mix valve until the preheat flames come down close to the tip and create that fine pretty feather effect. Guess I have some things to try this week.
I noticed shipyards were using Propane, so I switched from Acetylene to Propane 30 years ago (SO much cheaper, and only a LITTLE bit colder) and NEVER looked back.
Propane is about 75% cheaper to buy (plus you can get it just about anywhere today. I also use a small 1 lb bottle if I am on the road (so I only have to BUY and lug around one heavy O2 tank). While it is colder (5700F Acetylene vs 5100F for Propane,) but it also uses a lot LESS oxygen so for me it was a win win situation. This 600 lower temperature means nothing for 99.99% of the users I have a cheap set of torches and some single stage regulators (Look at ARKSEN Harris on Amazon) and have used and abused them for over 30+ years. You will need to buy an adapter to convert the Acetylene regulator to fit the propane bottle (About $5 at a welding store)The only thing I had to replace on the torch set was the rubber hoses about 5 years ago.
Richard Cournoyer Awesome, thank you! I'll definitely look into that, I was kind of skeptical but you aren't the only person who's said propane was better. Thanks!
Since my hobby workshop is in the cellar I decided for Acetylene. The heavier than air Propane is just to dangerous in this case. Otherwise I would also use Propane.
That bevel cut was nothing short of amazing. I have a lot to learn when it comes to torch work. It's always fun watching a true pro cutting steel. I probably would've fallen over if I saw 30 psi on the acetylene. I'm a bit scared of using it, to be honest, which can't be good from my cutting ability, but oxy/propane just doesn't do it. I guess if you're safe and mindful of your equipment that's all you can do. It just sucks having to keep an explosive device next to you all day, knowing that if you screw up, you're going to have a very, very bad day.
🤣 it was just 4 pieces of metal welded together... what plans could you need. Part of welding and fabrication is figuring it out. Think he had a set of plans when he built that one? No he had an idea for something and made it.
Funny I should find this video lol. I just bought a torch and regulators, second hand, and I had an irregular regulator too. Mine was the oxygen gauge that was faulty though. Now, this is in my little home shop so... super scary stuff. Went through proper procedure, turned it up to about 30lbs, it worked for about 3 seconds then I could feel the torch start to push back a bit, then a lot! By the time I got to the bottle to shut it down it had gotten to well over 150lbs! (literally bent the needle) I was pretty shook up by the whole ordeal, but also thankful it was me that got the torch set. If someone less experienced picked it up well, it could have been a lot worse. Needless to say, that regulator is stripped down and out of service and the %$^% that sold me the regulator got a serious earful. Sorry for the extra long comment, honestly it was pretty recent and I'm still venting about it 🤣. Thanks for the video, Bob! 👍😊👍.
Bob, thanks for this great video, so many super points. Before the days of u tube "older" people like myself had to rely on books. I never thought of kicking the O2 pressures up that high, but my plasma cutters often exceeds 70 lbs. Many who use a straight edge for a guide should note that your leading edge is elevated off the work surface, we'll I'll go back to my nap, once again thanks. J
I have inherited a 30+ year old oxy acetylene rig. The hoses appear to have lots of cracks. I would like to replace them and have seen hose sets at a local discount hardware store that are smaller in diameter but are relatively inexpensive. Say 50 ft for around 40 dollar's. Would it be ok to go to a smaller diameter hose. Also I would like to add a flame arrestor inline at the tanks and torch ends. What would be recommended as I have seen cheap and expensive ones online. I am new to welding. Any advice would be most appreciated. ppear to have lots of cracks and
I was expecting to see a little chipping hammer action... when he cleaned the slag off with that little striker I was really amazed! I'm MILES away from this action. When I cut something with a torch I'm really excited if the cut piece falls off by itself and I didn't get hurt.... The idea of cutting to a LINE and so on gives me something to live for.
Like your version of the straight edge with the stand off bar edge. Now I go add it to mine, wish I had thought of it year's ago! Never too old to learn new and different thing's Stay safe out there brothers.
I'm making a straight edge today at work like that, thanks for the idea Bob!!!also nice flame work sir. Thanks for sharing these little tricks and ideas, they help out quite a bit!!Often at work we have to cut 2'' and under by hand all the time and a nice little straight edge like that will help me...normally I just use a little aluminum straight edge but that is so so...
Things can go so wrong so fast with that pressurized gas. Once you see or hear about what happens when things go bad, you will either respect the hell out of it or walk away from it forever. Bob, once again you show us why you are the coolest cat on the planet! Great video.
A set of "tip cleaners" was always in my work bucket. Along with that I'd carry extra, different size tips. On a repair job, I'd swap out the company tip for mine (if necessary). Then swap back, when I was done.
Just started welding class. Not sure what the exact tip size was but it looked to be similar to yours a 00. I found it was easier to cut the thicker piece a 5/8 I believe. The thinner piece like a quarter inch or smaller wanted to melt back together when I was cutting. We were following corresponding victor tip charts and keeping acetylene not too far over 5 psi.
I’ve noticed you really only get the “pour” from the beveled cuts when cutting an edge. When you leave some land the Slag will build up at the bottom of the cut but usually flakes off and cut quality is comparably the same.
Can’t be too careful when it comes to flying bits of slag or hot metal. Keep a good eye on your hoses and the condition of your equipment. And what areas your cutting in. Having another pair of eyes watching what’s going on while your concentrated on your cut is always a good idea. I remember my father telling me he was up on an extension ladder cutting away with a brand new out of the box set of gauges on the bottles. Turned out they were a bad design by a reputable manufacturer. They had a plastic plug in the top and sparks were falling around and onto the bottles which were off to the side but still enough for a spark to drop into the plug, melt it and release and ignite the acetylene.The guys working in the factory actually bolted and my father raced down the ladder and turned the bottle off. After abusing the shit out of the CIG rep, all those gauges were recalled and removed from sale. So lesson learned, pay attention to your equipment. Cover things if need be. It could have gone horribly wrong.
Matt Tradie Go horribly wrong. Now there is an Understatement. More like a real bomb going off. No wonder your Dad cussed the rep out. Hard to hear but better than going to a Coronial Inquest.
Meanwhile we have a guy at our scrapyard blasting tons of metal away to the point he needs 2 propane tanks in his basket. He said he runs his oxygen at 180 with a size 6 Victor tip. He had so much condensation on his basket that he burned it all off only with propane. Regulators line and all.
Wow, this presentation is top notch! The first true welding master I've encountered anyway... the way you explain this information is just perfect. This channel seems to be one of those rare gems as far as welding info goes. Thanks gentlemen!
Bob I have had the same experience with multiple layers of protection and still get scale in my eyes. Probably 3 or 4 Times in my 40+ years of welding and burning.
Bob .. cleaning: you mentioned a mill file, yup, work good! But another old timers trick... Polish the soot dirt and junk off the outside of the tip too. Seems to help make a hotter cleaner flame. Otherwise, I've always just flown by the seat of my pants... Instinct I guess. My favorite torch set is an old Smith's, my dad picked it up used about 50 years ago. Tips are hard to find, so it's in a box in the shop😥 but back in the day, I could cut a nice clean smooth cut in 3/4" to 1" materials... With a torch rated to a maximum of 1/2" piercing...😎 Safety glasses, shield, goggles... The more you wear, the more chunks get through... I've made that trip to the eye doctor, that Dremel tool is psychedelic!! Bending and twisting the lens!!! LOL... I've been there 5 times in over 40 years. Each time I had all the protection I could have.. I'm a bad boy, don't always wear safety glasses... But when I do, I get a ride to town to see the eye doctor.. Accetaline... Ten pounds is usually a great plenty!! I've gone to 12 a few times.. makes me nervous!! 6 or 8 is great!!!
Bigger tip. Say, 4 or 5. (I like Harris) Pressure Gauges on torch. Two stage gauges at tank. 15 pounds propane, 65 oxygen. It’ll cut through most steel.
Get the old crew back LOL By the way those boots you wear look comfortable who makes them. Hell while i am at it, a video like the one today but with a plasma cutter would be super helpful. Thanks a lot
Maybe this was a "one-take" job? It must happen now and then. Anyway, I was really glad to have this information! I did some torch cutting this week and it wasn't nice at all! Let's try the burn-bar, at least go in a straight line!
I guess thick is relative. I was hoping to see some 3-6" stuff cut. My son replaced the 45 amp plasma cutter on his CNC table with an oxy torch to cut some 1" stuff. First cut was great. Haven't needed to cut anything thicker yet.
Thanks so much for the information. Been looking at getting a small oxy set up. I don’t do much but being able to do a little of everything would be nice. Enjoy learning from you guys. Thanks again!!!
I can't wait until I'm old enough and grumpy enough to throw around phrases like, "Im'ma do this cut 1-handed", or "Lemme' see if I can do a better cut than this robot". Got dern' legend right there.
Beautiful cuts, always good to learn a few tips from and old timer. Would like to see you try cutting that 3/4 plate, like the welder us to work with. He would use a 000 tip, 7 lbs acetylene and about 100 psi on oxygen.
Interesting. Have a question for you though. When I am burning, I always seems to get an unusual amount of slag at the bottom of the cut. Then I have to work at it to get it off. On the other hand, I've seen other guy/gals that can burn through almost anything and it looks like (almost) a machine did it. I was told I had too much oxygen coming out, too much gas. I've played with both many times and still have too much slag. Tip is always clean and a number 1 or 2 is used. Suggestions?
Jimmy Doe but if you're using a guide bar like in this vid it doesn't matter if your marks disappear while you're working, you line up the bar to your marks before you start and then just work from the bar. I still prefer a scribed mark, though, it should cut through any scale.
I realize this video is 2 years old but I do have a question... how do you prevent slag, or what are the causes creating slag when one does cutting??? Thanks! Your vid is wonderful!
I'm planning on buying some 1/2 and some 1 inch plate for a couple projects I have and my only means of cutting at the moment are a angle grinder and a chop saw. Almost looked into a harbor freight plasma cutter but that only does 1/4 inch at 120 volts i dont currently have a 240 setup in my garage so that won't work.
I don't even to make any video, yet, It is like I'm watching myself go (and yes! None touches my torch/tips/guides/etc) If I work for a shop full-time and can't have my own set of torch, I'll buy my own to work there just like I buy my own work-boots.
Haven't gas welded in years. Veteran, retired, built a forge, baught an arc welder (stick), and was gifted an old double carbon tip arc torch. Anxious to learn about it. Can I weld or cut with it? What is its main use? ... can you help me?
This is a skill I'd love and have never had the opportunity to get. Have always cut with chop saws or occasionally a plasma cutter, and always used a large bench grinder for bevelling plate
two things bob., show people the difference in the holes in different sizes of torch tips, i use a #2,4 and 8 tips in the shipyard. also how about showing how to cut with propane or propylene gases which are very common in commercial cutting operations because the gas is so much cheaper
Three things I have learned from this: 1, I guess I should preheat, 2, i should probably pay attention to pressures a bit more, and 3, I really don't know what I am doing, eventhough I own 3 torches, 2 MIGs and an AC/DC TIG.
Love your videos. Have a question or request for a video. I clean much of my new metal and then spray with a light coat of regular metal primer for storage from rust. In your opinion , does welding thru the light coat of primer affect the strength of a weld or how much. I would love to see an in-depth video with cut an etch test and bend test with primer and no primer on equal samples of same welds. All opinions would be appreciated.
I was watching some steel workers free hand cutting six inch thick steel with kerosene and oxygen. They said said they can use diesel, or gasoline as well. Gas and diesel is hotter then kerosene, but diesel is very sooty, and gasoline is to dangerous in confined space's.
Bob, I would like to see tips on oxy-fuel cutting thin metal as in 3/8" and thinner, I have more trouble with cleanly cutting them than I do thicker stock mostly blow outs and thick slag on the bottom of the cut, if you get a chance to I would greatly appreciate it and keep the videos coming 😊
Hi bob seen many videos on oxy cutting. Can you make some videos on cutting old rusty beam. As in the construction site there are old and rusty I beam which are layered and thick ones.
I have a question that may sound stupid. When should you stop using the oxygen from the cylinder? Is it a case of going until you lose all pressure or should you stop before that. I have flashback arrestors fitted if that makes a difference.
Thanks for the informative videos. It would have been great if the guide beveled cut was retained to compare with the hand beveled cut. Impressive hand cutting and good look at your homemade hand cutting straightedge.
Just wanted to take a minute to thank you Bob. You and the entire team are an asset and I've learned a great deal from watching.
Thanks Bob. I'm killing it at my new job with all of your expert advice stuck in my head. I'm 50 and still learning thanks to you sacrificing your time to share your knowledge. Much appreciated.
A little trick that will make that cutting edge slicker is run a piece of soapstone along the edge. Slicker than snail snot. Torch will glide right along and never try to drag.
11
Tried it today. Beautiful.
Thanks for making this farmer better with a torch and welder as I never had the opportunity to go to school for this knowledge
Hi Bob, and thanks for another QUALITY training video.
Our shop had a setting of 12/42 for everything. Of course we worked with heavy steel all the time and kept big tips on the torches.
Here's a trick an old boiler-maker taught me, over 40 years ago, that works really well for cleaning your cutting tip, right before you start cutting. Get a rough-cut Oak 2x4 x 18" long. You can use that as a rest to keep the heat away from your hand...that and a C-clamp vice grip. Get your flame ready to cut. Squeeze the Oxy handle and place the face of the tip onto the face of the Oak board, and drag it to you...like 6" in 2 seconds fast. Then immediately put it to the metal, get the puddle and start your cut. You'll be amazed at the difference! He said the Oak carbon blows out the mill-scale and cleans your tip...HOT. Then it's ready to eat!
I appreciate your videos!
Please advise ALL your students to NEVER oil the threads on your bottle caps nor get oil anywhere around oxygen! It will blow up!Very dangerous! The 3 piece bottle caps are the way to go. Screw them on, hinge them closed and put the pin in the hole. When not using torch. That way, if for some reason the securement for the tank releases its hold on the tank, the valve will be protected!
THANKS FOR POSTING
Thanks Bob!
I really enjoy the peaceful way you explain the stuff. Greetings from Spain.
Hidy. Thanks for another wonderful video. You were speaking about tip cleaning...an old boilermaker taught me a kewl cleaning trick, back 40 years ago...take a rough-cut Oak 2x4x12" with you, everywhere you work. Most of the steel he would cut was 2" thick end sheets and 1" on snow-plows (which are modern day cow catchers), on the end of a Locomotive. He says...when your tip starts singing to ya, keep it lit and press the cut trigger and put the tip right on the face of thw wood and drag it along wit the tip touching the wood. The flames will force away...back up toward the torch. Rub the tip on the wood with the trigger pulled, for 4 or 5 three inch rubs and then pull it away from the wood. If the tip was full of scale, the oak will boil it out and the tip will be cleaner than if you ran a wire file into its ports and the end will be like a new tip! Needless to say, I keep a rough cut Oak 2" x 4" x 12" in my welding bay all the time, for tip cleaning. Try that one out
I always refer to the charts that come inside the Victor cutting torch manual .... It has travel speed and pressures listed. It's never let me down. Thanks for video.
Not sure why anyone would watch any other welding videos. Weld.com is the best I have ever seen.
Worth watching 2-3 times. Thanks
Im watching over than that
Your too humble, well done sir I wish you were my instructor when I was learning.
Used a Oxy Ace for a couple of years. Probably have 500 hours on them. Mostly 1/4 to 1/2 plate. The very first thing you said, imho, was the most important. You have to keep the oxygen jet orifice "pristine" for good cuts.
You're definitely a pro. I have a lot of respect for your craft
Finally someone who knows how to set pressures !! 💪🤙
Excellent video. I’m afraid the torch is under appreciated. I would love to see more videos on the torch. I learned more here about cutting to correct some of my errors. Keep up the good work and don’t gloss over the common knowledge some that really isn’t so common.
EXCELLENT VIDEO, BOB!!!! I truly enjoy watching and learning from You!!
You ARE AN EXCELLENT TEACHER AND SPEAKER!!! 👍👍👍😃😃😃
very good lesson, i needed that one, thanks, my oxygen regulator blew the fusible plug out for some reason when i cracked the valve open, it is a Victor set, scared me to death, the set has been used very little but they are several years old.. keep up the good work that you do for all of us, thanks again,,
Nice clean job. I also like that you are keeping your shop tidy
Yep ! Always tell my helpers
"PRE-HEAT, & PATIENCE ! PRE-HEAT, & PATIENCE !" You'll end up with a beautiful cut ! When they don't listen I tell them to clean up their own mess with the 7" grinder !!
I also tell them "OLD AGE, AND TREACHERY WILL ALWAYS OVERCOME YOUTH, AND SKILL !!"
😁😁😁😁👍👍👍😉✌
LOL! THAT'S MY FAVORITE SAYING ALSO!!
GOTTA KEEP THE PUPS ON THEIR TOES!!
You are a MASTER! WOW!! Your students are so lucky. Bootcamp??
Great Video Bob, Unless the camera is not showing it good I have been adjusting my torch wrong for 40 years. I have always open the mix valve until the preheat flames come down close to the tip and create that fine pretty feather effect. Guess I have some things to try this week.
Excellent video as always Bob, your beveled hand cut is a thing of beauty!
Sarah Loyd Thanks Sarah. I used to be pretty smooth when I was a young man.
You have still got it Bob :-)
Never could use a burn bar worth a hoot. Never could get that perfect glide pressure so I free hand everything. Good job Bob
I noticed shipyards were using Propane, so I switched from Acetylene to Propane 30 years ago (SO much cheaper, and only a LITTLE bit colder) and NEVER looked back.
Having a two piece tip is easier to clean too. I don't know why anybody would want to use acetylene.
Richard Cournoyer I'm 17 and looking to buy a torch. Would you recommend I go with propane? What have your experiences been with propane vs acetylene?
Propane is about 75% cheaper to buy (plus you can get it just about anywhere today. I also use a small 1 lb bottle if I am on the road (so I only have to BUY and lug around one heavy O2 tank). While it is colder (5700F Acetylene vs 5100F for Propane,) but it also uses a lot LESS oxygen so for me it was a win win situation. This 600 lower temperature means nothing for 99.99% of the users I have a cheap set of torches and some single stage regulators (Look at ARKSEN Harris on Amazon) and have used and abused them for over 30+ years. You will need to buy an adapter to convert the Acetylene regulator to fit the propane bottle (About $5 at a welding store)The only thing I had to replace on the torch set was the rubber hoses about 5 years ago.
Richard Cournoyer Awesome, thank you! I'll definitely look into that, I was kind of skeptical but you aren't the only person who's said propane was better. Thanks!
Since my hobby workshop is in the cellar I decided for Acetylene. The heavier than air Propane is just to dangerous in this case. Otherwise I would also use Propane.
Wow...such nice clean cuts. Seeing this makes me realize I need to work on my cutting to improve it . Thanks
That bevel cut was nothing short of amazing. I have a lot to learn when it comes to torch work. It's always fun watching a true pro cutting steel. I probably would've fallen over if I saw 30 psi on the acetylene. I'm a bit scared of using it, to be honest, which can't be good from my cutting ability, but oxy/propane just doesn't do it. I guess if you're safe and mindful of your equipment that's all you can do. It just sucks having to keep an explosive device next to you all day, knowing that if you screw up, you're going to have a very, very bad day.
If you see this straight-edge in the video and have to ask for a plan I suggest switching profession.
Several have asked!!
@@bobmoffatt4133 Does anyone know the term - Use your brain housing group anymore?
Not everybody starts as a pro..
What do you mean
🤣 it was just 4 pieces of metal welded together... what plans could you need. Part of welding and fabrication is figuring it out. Think he had a set of plans when he built that one? No he had an idea for something and made it.
Funny I should find this video lol. I just bought a torch and regulators, second hand, and I had an irregular regulator too. Mine was the oxygen gauge that was faulty though. Now, this is in my little home shop so... super scary stuff. Went through proper procedure, turned it up to about 30lbs, it worked for about 3 seconds then I could feel the torch start to push back a bit, then a lot! By the time I got to the bottle to shut it down it had gotten to well over 150lbs! (literally bent the needle) I was pretty shook up by the whole ordeal, but also thankful it was me that got the torch set. If someone less experienced picked it up well, it could have been a lot worse.
Needless to say, that regulator is stripped down and out of service and the %$^% that sold me the regulator got a serious earful. Sorry for the extra long comment, honestly it was pretty recent and I'm still venting about it 🤣.
Thanks for the video, Bob! 👍😊👍.
So you slammed an old reg and thought you’d give the seller an earful?
@@agoniaXdunya it looked brand new. As to answer your question, the fella sold me a dangerously faulty tool and I gave him an earful 😏.
Bob, thanks for this great video, so many super points. Before the days of u tube "older" people like myself had to rely on books. I never thought of kicking the O2 pressures up that high, but my plasma cutters often exceeds 70 lbs. Many who use a straight edge for a guide should note that your leading edge is elevated off the work surface, we'll I'll go back to my nap, once again thanks. J
I have inherited a 30+ year old oxy acetylene rig. The hoses appear to have lots of cracks. I would like to replace them and have seen hose sets at a local discount hardware store that are smaller in diameter but are relatively inexpensive. Say 50 ft for around 40 dollar's. Would it be ok to go to a smaller diameter hose. Also I would like to add a flame arrestor inline at the tanks and torch ends. What would be recommended as I have seen cheap and expensive ones online. I am new to welding. Any advice would be most appreciated.
ppear to have lots of cracks and
Excellent torch hand Bob. All those cuts are superb !!!
I was expecting to see a little chipping hammer action... when he cleaned the slag off with that little striker I was really amazed! I'm MILES away from this action. When I cut something with a torch I'm really excited if the cut piece falls off by itself and I didn't get hurt.... The idea of cutting to a LINE and so on gives me something to live for.
Great demo of a very practical skill. Gotta get busy and build myself a burn bar.
Thanks Bob.
Like your version of the straight edge with the stand off bar edge.
Now I go add it to mine, wish I had thought of it year's ago! Never too old to learn new and different thing's
Stay safe out there brothers.
I'm making a straight edge today at work like that, thanks for the idea Bob!!!also nice flame work sir. Thanks for sharing these little tricks and ideas, they help out quite a bit!!Often at work we have to cut 2'' and under by hand all the time and a nice little straight edge like that will help me...normally I just use a little aluminum straight edge but that is so so...
Awesome. I only wish i was 1/8 that good. Thanks for the tips. One of my favorites.
Things can go so wrong so fast with that pressurized gas. Once you see or hear about what happens when things go bad, you will either respect the hell out of it or walk away from it forever. Bob, once again you show us why you are the coolest cat on the planet! Great video.
A set of "tip cleaners" was always in my work bucket. Along with that I'd carry extra, different size tips. On a repair job, I'd swap out the company tip for mine (if necessary). Then swap back, when I was done.
Just started welding class. Not sure what the exact tip size was but it looked to be similar to yours a 00. I found it was easier to cut the thicker piece a 5/8 I believe. The thinner piece like a quarter inch or smaller wanted to melt back together when I was cutting. We were following corresponding victor tip charts and keeping acetylene not too far over 5 psi.
I’ve noticed you really only get the “pour” from the beveled cuts when cutting an edge. When you leave some land the Slag will build up at the bottom of the cut but usually flakes off and cut quality is comparably the same.
Can’t be too careful when it comes to flying bits of slag or hot metal. Keep a good eye on your hoses and the condition of your equipment. And what areas your cutting in. Having another pair of eyes watching what’s going on while your concentrated on your cut is always a good idea. I remember my father telling me he was up on an extension ladder cutting away with a brand new out of the box set of gauges on the bottles. Turned out they were a bad design by a reputable manufacturer. They had a plastic plug in the top and sparks were falling around and onto the bottles which were off to the side but still enough for a spark to drop into the plug, melt it and release and ignite the acetylene.The guys working in the factory actually bolted and my father raced down the ladder and turned the bottle off. After abusing the shit out of the CIG rep, all those gauges were recalled and removed from sale. So lesson learned, pay attention to your equipment. Cover things if need be. It could have gone horribly wrong.
Matt Tradie Go horribly wrong. Now there is an Understatement.
More like a real bomb going off. No wonder your Dad cussed the rep out. Hard to hear but better than going to a Coronial Inquest.
Meanwhile we have a guy at our scrapyard blasting tons of metal away to the point he needs 2 propane tanks in his basket. He said he runs his oxygen at 180 with a size 6 Victor tip. He had so much condensation on his basket that he burned it all off only with propane. Regulators line and all.
Wow, this presentation is top notch! The first true welding master I've encountered anyway... the way you explain this information is just perfect. This channel seems to be one of those rare gems as far as welding info goes. Thanks gentlemen!
Great video! Awesome torch work! Please consider the outtakes again. Those were hilarious
We are going to work on those.
Bob I have had the same experience with multiple layers of protection and still get scale in my eyes. Probably 3 or 4 Times in my 40+ years of welding and burning.
Bob .. cleaning: you mentioned a mill file, yup, work good! But another old timers trick... Polish the soot dirt and junk off the outside of the tip too. Seems to help make a hotter cleaner flame.
Otherwise, I've always just flown by the seat of my pants... Instinct I guess. My favorite torch set is an old Smith's, my dad picked it up used about 50 years ago. Tips are hard to find, so it's in a box in the shop😥 but back in the day, I could cut a nice clean smooth cut in 3/4" to 1" materials... With a torch rated to a maximum of 1/2" piercing...😎
Safety glasses, shield, goggles... The more you wear, the more chunks get through...
I've made that trip to the eye doctor, that Dremel tool is psychedelic!! Bending and twisting the lens!!! LOL... I've been there 5 times in over 40 years. Each time I had all the protection I could have..
I'm a bad boy, don't always wear safety glasses... But when I do, I get a ride to town to see the eye doctor..
Accetaline... Ten pounds is usually a great plenty!! I've gone to 12 a few times.. makes me nervous!! 6 or 8 is great!!!
Bought my first oxy-acetylene set and bottles today... I’m in love!
Thanks for the info on Mill scale. Going to to try to make that straight edge too.
Bigger tip. Say, 4 or 5. (I like Harris)
Pressure Gauges on torch. Two stage gauges at tank. 15 pounds propane, 65 oxygen. It’ll cut through most steel.
What happened to the out takes at the end of the video. Always enjoyed them, thanks
redtailhardwoods New crew.
Get the old crew back LOL By the way those boots you wear look comfortable who makes them. Hell while i am at it, a video like the one today but with a plasma cutter would be super helpful. Thanks a lot
Maybe this was a "one-take" job? It must happen now and then. Anyway, I was really glad to have this information! I did some torch cutting this week and it wasn't nice at all! Let's try the burn-bar, at least go in a straight line!
I guess thick is relative. I was hoping to see some 3-6" stuff cut. My son replaced the 45 amp plasma cutter on his CNC table with an oxy torch to cut some 1" stuff. First cut was great. Haven't needed to cut anything thicker yet.
Thanks so much for the information. Been looking at getting a small oxy set up. I don’t do much but being able to do a little of everything would be nice. Enjoy learning from you guys. Thanks again!!!
Thanks Bob. Excellent instructions as always. Very helpful.
Excellent video, Bob!
Could you do a video on alternative fuels also, such as propane?
Excellent Bob, thank you very much...! Cheers from Canada...
Thanks Bob
Wish I was half as good, as you are sir ! 👍👍
Bob, thank you for the great instruction. I greatly appreciate your time and skill.
I can't wait until I'm old enough and grumpy enough to throw around phrases like, "Im'ma do this cut 1-handed", or "Lemme' see if I can do a better cut than this robot". Got dern' legend right there.
A true wizard at work here
A quick message for Bob, Hope youre doing well buddy! Looking forward to seeing you again in more videos in the future!
I really appreciate the support!
Beautiful cuts, always good to learn a few tips from and old timer. Would like to see you try cutting that 3/4 plate, like the welder us to work with. He would use a 000 tip, 7 lbs acetylene and about 100 psi on oxygen.
Bob Moffat is a National Treasure!
Interesting. Have a question for you though. When I am burning, I always seems to get an unusual amount of slag at the bottom of the cut. Then I have to work at it to get it off. On the other hand, I've seen other guy/gals that can burn through almost anything and it looks like (almost) a machine did it.
I was told I had too much oxygen coming out, too much gas. I've played with both many times and still have too much slag.
Tip is always clean and a number 1 or 2 is used.
Suggestions?
Tom McDaniel .. see my post above.
Good info on this Bob would you recommend removing the mill scale before cutting.
I find if you mark on mill scale the marks disappear as opposed to when you clean it off your soapstone marks stay true and visable
Jimmy Doe but if you're using a guide bar like in this vid it doesn't matter if your marks disappear while you're working, you line up the bar to your marks before you start and then just work from the bar. I still prefer a scribed mark, though, it should cut through any scale.
Please more oxy fuel stuff. I really enjoy the versatility! Thanks
Men this gentlemen is a legend my respet
Thank you so much for your videos. I’d love to get formal training .
I realize this video is 2 years old but I do have a question... how do you prevent slag, or what are the causes creating slag when one does cutting??? Thanks! Your vid is wonderful!
I'm planning on buying some 1/2 and some 1 inch plate for a couple projects I have and my only means of cutting at the moment are a angle grinder and a chop saw. Almost looked into a harbor freight plasma cutter but that only does 1/4 inch at 120 volts i dont currently have a 240 setup in my garage so that won't work.
I don't even to make any video, yet, It is like I'm watching myself go (and yes! None touches my torch/tips/guides/etc) If I work for a shop full-time and can't have my own set of torch, I'll buy my own to work there just like I buy my own work-boots.
Haven't gas welded in years. Veteran, retired, built a forge, baught an arc welder (stick), and was gifted an old double carbon tip arc torch. Anxious to learn about it. Can I weld or cut with it? What is its main use? ... can you help me?
Bravo vrlo poucno upustvo ste prikazali
You cut it smoother than the old track torch...
Love your videos bro...keep it coming!
Very useful demo Bob - thank you. :)
Its the most basic tools that are the most valuable.
Mr. greens boat tanks and aluminium welding Very true!
This is a skill I'd love and have never had the opportunity to get. Have always cut with chop saws or occasionally a plasma cutter, and always used a large bench grinder for bevelling plate
two things bob., show people the difference in the holes in different sizes of torch tips, i use a #2,4 and 8 tips in the shipyard. also how about showing how to cut with propane or propylene gases which are very common in commercial cutting operations because the gas is so much cheaper
Very good video.
Three things I have learned from this: 1, I guess I should preheat, 2, i should probably pay attention to pressures a bit more, and 3, I really don't know what I am doing, eventhough I own 3 torches, 2 MIGs and an AC/DC TIG.
This cuts are 👍😍 great video! Thank you
Love your videos. Have a question or request for a video. I clean much of my new metal and then spray with a light coat of regular metal primer for storage from rust. In your opinion , does welding thru the light coat of primer affect the strength of a weld or how much. I would love to see an in-depth video with cut an etch test and bend test with primer and no primer on equal samples of same welds. All opinions would be appreciated.
Primer may leave porosity at times. I would clean it away from the weld area. I wouldn't want to be breathing the fumes either.
I was watching some steel workers free hand cutting six inch thick steel with kerosene and oxygen. They said said they can use diesel, or gasoline as well. Gas and diesel is hotter then kerosene, but diesel is very sooty, and gasoline is to dangerous in confined space's.
All three require special torch tips, and other special equipment, but can burn all day on one 5 gallon tank of kerosene.
By the way, it was the scrapping of Bertha, the Seattle tunnel machine that was being cut.
Wow, I am just amazed at your skill sir.
Good information man, much appreciated
Very nice cuts mine look like S . Yea trying to look at yours . You do a great job .
Great video
Love your vids Bob. Beautiful clean cuts there.
Keep em comin! 👍
Bob, I would like to see tips on oxy-fuel cutting thin metal as in 3/8" and thinner, I have more trouble with cleanly cutting them than I do thicker stock mostly blow outs and thick slag on the bottom of the cut, if you get a chance to I would greatly appreciate it and keep the videos coming 😊
Damn, Bob was so good.
Very nice Bob.
Love your videos!
Bob at his best
I used to cut 2 inch thick with a 16 tip with rasorgas and oxy but you can't buy it in australia any more it was cheap to
that was a clean and nice cut...
Such a cute little torch. I run number 7 victor tips. 10” worth of bad ass molten metal.
Love your videos viejon. Respect
Hi bob seen many videos on oxy cutting. Can you make some videos on cutting old rusty beam. As in the construction site there are old and rusty I beam which are layered and thick ones.
Bob Moffatt You have a couple- cutting videos where you dial in torch and set it to that 'ripping' sound, is that just on smaller thickness material?
Great vid!
Good one Teach! Have you pondered making a video, while making another circle cutting tool?
I have a question that may sound stupid. When should you stop using the oxygen from the cylinder? Is it a case of going until you lose all pressure or should you stop before that. I have flashback arrestors fitted if that makes a difference.
Thanks for the informative videos. It would have been great if the guide beveled cut was retained to compare with the hand beveled cut. Impressive hand cutting and good look at your homemade hand cutting straightedge.