If build a transfer case, i would want to add gears to it, besides 2&4wd, hi & lo, a 🐢 ultra low gear. + Low gear, medium, 1:1, then a 10% , 20%, 35% 50% over drive ratios, along with a 2wd only, 4wd only, a separate shifter for 2&4wd. Basically a 5-speed transmission bolted in a 5speed transmission,with a few extra gears added. then the 1 transmissions gears can be split. 1st gear, +low,med ,high, 2nd,+low ,med,hi , 3rd +L. ,M. Hi 4th, +L,M,Hi., 5th+ L,M,Hi. Then the other 5gear, 15 gears + another overdrive gear!😮 It would be like a semi truck. Only more like a 1/4ton truck over loaded and under powered! Allowing a 10hp Diesel engine to carry the truck loaded, it may run like a Hurd of turtles, but it would climb a tree, if it had traction.. i do want to build a tractor, 4x4, micro tractor , with 33"x12.5" tires , and debating on the engine, either a 5-10 hp mower style engine or a car engine. From 2.2 litre 4cyl, to 4.0L v6. Or electric using forklift motor, 10-12 kw. x 2, one can be used as the PTO, or shifted to power the tractor. Id build it with 4wheel steering with a short wheel base. Not much more than 24" between tires , and 44" tires may be added later, use two rear diffs from a mustanf or dodge , with the same ratio, put a 34tooth sprocket on the input, drive it with a 11 tooth, along with a 5-speed use s 1.5" shaft to drive both, with a pair of 12 tooth speockets on the shaft one on the transmission out shaft. To keep 1:1, but have other available. A 2:1 over drive, a 1:2 underdrive. To make good power and slow speed the final drive should equal 6.50:1-7.00:1 plus 1st gear, it should have thr TQ to spin the earth. At 1 mile per year. And run another shaft from the transmission input shaft, probably a chain drive or belt drive. With another independent drive with a 2:1 reduction and the transmission gets a 50 lb flywheel a 4" channel iron frame, with a 2" tube bracing and cab, with 1" tubing and 2" angle , with a 60' wide 16" scrape blade with 24" travel , also a. 16x60 bucket with a dump function. The lift by winch. The dump, possibly linear actuator. Maybe hydraulics eventually. Possibly powered by 2, old school 5hp engines or scale the whole thing up 10% and use a car engine. Have a awesome day...
Vip qua ido oi
Thanh kiu
Ficou muito bom parabéns aqui é BRASIL
Thank you very much
0:19 ⭐️⭐️⭐️
🥰thank you
Luar biasa
Good 👍👍
Thank you
Good job💪
Thanks Bro
Привет! Молодцы! 🤝👍👍👍👍👍 у нас мороз , -24 ! 😢 ни чего не дает делать!
❤❤❤❤
Nice👏👏
If build a transfer case, i would want to add gears to it, besides 2&4wd, hi & lo, a 🐢 ultra low gear. + Low gear, medium, 1:1, then a 10% , 20%, 35% 50% over drive ratios, along with a 2wd only, 4wd only, a separate shifter for 2&4wd. Basically a 5-speed transmission bolted in a 5speed transmission,with a few extra gears added. then the 1 transmissions gears can be split. 1st gear, +low,med ,high, 2nd,+low ,med,hi , 3rd +L. ,M. Hi 4th, +L,M,Hi., 5th+ L,M,Hi. Then the other 5gear, 15 gears + another overdrive gear!😮 It would be like a semi truck. Only more like a 1/4ton truck over loaded and under powered! Allowing a 10hp Diesel engine to carry the truck loaded, it may run like a Hurd of turtles, but it would climb a tree, if it had traction.. i do want to build a tractor, 4x4, micro tractor , with 33"x12.5" tires , and debating on the engine, either a 5-10 hp mower style engine or a car engine. From 2.2 litre 4cyl, to 4.0L v6. Or electric using forklift motor, 10-12 kw. x 2, one can be used as the PTO, or shifted to power the tractor. Id build it with 4wheel steering with a short wheel base. Not much more than 24" between tires , and 44" tires may be added later, use two rear diffs from a mustanf or dodge , with the same ratio, put a 34tooth sprocket on the input, drive it with a 11 tooth, along with a 5-speed use s 1.5" shaft to drive both, with a pair of 12 tooth speockets on the shaft one on the transmission out shaft. To keep 1:1, but have other available. A 2:1 over drive, a 1:2 underdrive. To make good power and slow speed the final drive should equal 6.50:1-7.00:1 plus 1st gear, it should have thr TQ to spin the earth. At 1 mile per year. And run another shaft from the transmission input shaft, probably a chain drive or belt drive. With another independent drive with a 2:1 reduction and the transmission gets a 50 lb flywheel a 4" channel iron frame, with a 2" tube bracing and cab, with 1" tubing and 2" angle , with a 60' wide 16" scrape blade with 24" travel , also a. 16x60 bucket with a dump function. The lift by winch. The dump, possibly linear actuator. Maybe hydraulics eventually. Possibly powered by 2, old school 5hp engines or scale the whole thing up 10% and use a car engine. Have a awesome day...
Nice
The next road tes
Thank you for watching the video
VERRY GOOD please video how made front exel gardan
i am from indonesia
In my channel
@@2TDIY oke thank you sou much
Если это реверс.редуктор, то можно сделать из трёх конических шестерен.
❤❤❤❤❤❤❤
❤
⭐️⭐️⭐️
Ini lagi Di rantau bossqu, bila dh balik nnti, dua set aku pesan, Sgt rasio bosss
Thank you very much
ntastik
Giá sao vậy a
1tr a
Nice👏👏
Thank you