I have a small bldc motor wired in a y configuration and I have the N channel mosfets I just need 10k ohm resistors, 4.7 k ohm resistors, 100k variable resistor / potentiometer and diodes.
😂😂😂 какая аккуратная, автор даже не понимает при какой температуре что паять накляксал на провод припоя даже без флюса тк родного в припое не хватило！это 1 а 2 сомневаюсь я что эта схема юного птенца работает так радужно как показал автор этого видео！
This 3 phase bldc motor controllers using IRFZ44N or IRF3205 transistors are overpowered ones which can easily spin high watt bldc motor smoothly without heating up compared to pre programmed esc . But the only problem is that it cannot run the motor at same direction every time
Friend, good afternoon. I have 2 questions for you: Does the IRFZ34N work? of these I have 2. and I have 2 IRF3205. Can I use 2 IRF3205 and 1 IRFZ34N if the latter works? Thanks in advance for your answer.
You can use any Mosfet transistor, for voltages up to 50 V. You can successfully use Z 44. But, calculate the consumption to put enough transistors in parallel to support the current ! At a high current, the transistor heats up . That is why it is recommended to calculate 7 A, for each transistor. The tranzistor also carries 50 A, but the radiator must be ventilated. You want 30 A, put 4-6 transistors.
Мне кажется что, что-то скрывается в этом видео. Всё собрал как на видео и проверил по схеме, всё верно. Но при запуске двигатель пытается провернуться и не может, заодно греется очень быстро и сильно. В конце концов сжог двигатель.
Nice looking job. but it didn't work when I tried it. It was only humming while the rotor was shaking . Please sir kindly throw more light on this for me.
Купил точно такие детали, спаял точно как на видео. Моторчик подключил, а он не крутится. Иногда получается рукой подтолкнуть чтобы работал. Что может быть не так ?
@@caralicik4134 sudah, ternyata tidak bagus 😂😂. Setiap pertama kali di-on-kan, arah putaran tidak tetap, bisa cw atau ccw. Seperti motor ac induksi tanpa kapasitor.
Hola saludos amigo. Excelente video buen proyecto te felicito. Quisiera preguntarle algo, es una duda que tengo desde hace tiempo. Es posible fabricar un controlador para un motor alternador hecho a motor. No he visto videos de alguien que haya hecho algo así. Fabricar un controlador que controle 100a
I love the circuit but I absolutely hate the construction method of building in space. Things could be so much more practical if made on pcb board. 👍🏼☹️
may i use it in my drone ..?And is that ESC heating or burning when it run with motor contuinously ..? I don't want to take any risk with my BLDC motors .
Good afternoon dear, i have two questions please if i may ask, it's about the direction of the spinning can it be operated in opposite direction? And can it applicable to use a propeller on it?
Still useful in 2024 and ahead. Liked, subscribed and shared. Thanks from Bangladesh.
Thanks for the sub!
Very very fast harddisk BLDC motor 👍🏻👍🏻❤️❤️🙏🏻
Сборка рабочая проверено, но нужно добавить защиту от КЗ
2:37 Что-то не понял, за счёт чего открываются полевики?
@@Thinking_Man они по очереди открывают друг друга с очень большой скоростью
@@Thinking_Man ЭДС самоиндукции обмоток двиг-ля
three 10k resistors (1.24min in the video) are missing in the diagram
Nice work
Make pcb for this
Nice..but I didn't understand what is the purpose ofcall these electronics parts. Please make videos teach us for what is used each part.
Your the best ✊
*Puedes hacer un decodificador de código con tarjeta*
100 watt inverter made With p55 mospad vedio please
Nguồn vào tối đa là bao nhiêu vol vậy bạn
Great project. But please it will be nice if you added a circuit diagram.
God job
●๋•ηι¢є ιηƒσ●๋•
Bisa dibuat refrensi sistem acg stater( indonesia )
Thanks ✴Pareng
Really great sir
Vou escrever em meu idioma; esse cara só sabe fazer o básico.! Estou esperando o controle brushless de somente 3 fios
É um ótimo projeto mas, na montagem ele usou quatro resistores um de 4k7 e três de 10k e no esquema elétrico não tem os de 10k.
Qual esquema?
Приведённая автором схема не соответствует тому что он спаял. Вместо диодов D3, D4, D5 были припаяны резисторы по 10Kom
diodes are OK, but there is lack of the resistors 10k.
Если двигатель остановить руками он больше не запустится пока не отключишь питание и снова не включишь, а если двигатель стоит значит это и есть КЗ
👍
GOOD JOB ! ;)
I have a small bldc motor wired in a y configuration and I have the N channel mosfets I just need 10k ohm resistors, 4.7 k ohm resistors, 100k variable resistor / potentiometer and diodes.
Your circuit diagram shown in this video is wrong
Very good 👍
This better work the faith of humanity depends on it..
0
aTtiny85 4 channel relay remote kit program video please sir
Thanks for video,how many watts are the ressistors 10 k?1/2 or more?
I've used 1/4watt
in the diagram the 4.7k R goes to ground..in the video it is in series with the gates diodes
Nice work bro 👍🏼 bldc driver n controler in one
What kind of mosfet should I use to control 36v battery, 250w brushless motor, thanks
Is that like fish paper
Can it be used at what voltage intervals and how many watts of output power? I want to try practicing. Thank You
Amigo como puedo hacer uno de esos pero que funcione con 36v de alimentacion?
First
Circuit diagram is different from actual circuit, 10k resistors missing in diagram
Interesting, thanks. I'm going to put this on a private playlist and study it more closely.
Very good 🙂😊😊😊😊😊🙂🙂
Can it be used to power a car alternator that is converted to a motor
Аккуратная пайка навесом, автор молодец. Я сам такой же перфекционист.
😂😂😂 какая аккуратная, автор даже не понимает при какой температуре что паять накляксал на провод припоя даже без флюса тк родного в припое не хватило！это 1 а 2 сомневаюсь я что эта схема юного птенца работает так радужно как показал автор этого видео！
@@ПётрРоманюк-м3п она в принципе не может работать, где генератор импульсов?
Parabéns amigo , o projeto é seu
Excelente. Podrías realizarlo con un motor de 3 terminales. Muchas gracias.
This 3 phase bldc motor controllers using IRFZ44N or IRF3205 transistors are overpowered ones which can easily spin high watt bldc motor smoothly without heating up compared to pre programmed esc . But the only problem is that it cannot run the motor at same direction every time
How do we fix that?
@@renderuthis Turn the motor with finger in the direction you want before power it up. LOL
@@tigranohanyan3321 Hi, what about using an electrolyte capacitor to determine the direction?
@@sgrajendran8706 how? Explain
Friend, good afternoon. I have 2 questions for you: Does the IRFZ34N work? of these I have 2. and I have 2 IRF3205. Can I use 2 IRF3205 and 1 IRFZ34N if the latter works? Thanks in advance for your answer.
Can it work with IRF3205?
Please share circuit for 24v BLDC motor.tanks
Cuando el motor brushles es de 3 líneas como va conectado?
brilliant!! a beautiful pro job.
How many watts of this esc..
I love it good
Keep uploading videos like this
great video, thanks for sharing with us
Sir I want 12 to 36 volts. 30amps bldc. Correct MOSFET resister diode ple give me
Thankyou 🙏
If i want to 310v bldc ?
@@tebbink use IGBT transistor...
@@MIX-TEC-TV where is the video can i get it?
You can use any Mosfet transistor, for voltages up to 50 V. You can successfully use Z 44.
But, calculate the consumption to put enough transistors in parallel to support the current !
At a high current, the transistor heats up . That is why it is recommended to calculate 7 A, for each transistor. The tranzistor also carries 50 A, but the radiator must be ventilated.
You want 30 A, put 4-6 transistors.
Hii, how can I connect this to HDD motor with only 3 pine??
You can't with this circuit
This just for star config
Thank you🎉😊😊😊🎉🎉🎉🎉😅😅😮😢😮😮😮😮😮😮🎉🎉🎉🎉🎉🎉🎉🎉🎉🎉🎉🎉🎉🎉🎉🎉🎉😢🎉😢😢😢🎉🎉🎉🎉🎉🎉🎉🎉🎉🎉🎉😊😊😊😊😊😊😊😊😊😊😊🎉🎉🎉🎉🎉🎉🎉🎉🎉🎉😢🎉🎉🎉🎉
¿Podría hacer un controlador para un motor de tres terminales?
Dikhaya kuchh aor babaya kuchh aor .inout 2 wire output 3 wire bina ke dikhao mohtrum
Thanks for sharing
Мне кажется что, что-то скрывается в этом видео.
Всё собрал как на видео и проверил по схеме, всё верно.
Но при запуске двигатель пытается провернуться и не может, заодно греется очень быстро и сильно.
В конце концов сжог двигатель.
Такая же херня....
Nice looking job. but it didn't work when I tried it. It was only humming while the rotor was shaking . Please sir kindly throw more light on this for me.
❤ from Pakistan
How much ampare or watts plz reply
Can you tell me the voltage and amperage required to run this
But is this ESC made only for hall sensored motors or is made for motors without them.🧐🤔 And how you control the rotation direction, thanks.
Lo voy a hacer! Gracias Genio!
How the Gates are charged with both biodes in reverse direction??
Good working bro
great work ❤🔥
hi, would you kindly share esc using igbt
Купил точно такие детали, спаял точно как на видео. Моторчик подключил, а он не крутится. Иногда получается рукой подтолкнуть чтобы работал. Что может быть не так ?
Попробуйте запитать от 12 вольт
genius idea, you are great...i'll try it later.
Udah nyoba belum bang?
@@caralicik4134 sudah, ternyata tidak bagus 😂😂.
Setiap pertama kali di-on-kan, arah putaran tidak tetap, bisa cw atau ccw. Seperti motor ac induksi tanpa kapasitor.
Saya kira, aku doang bang hahah
@@caralicik4134 Aku kira juga lumayan, tapi sangat jauh dari harapan. Nanti coba saya review di channel saya.
@@YudiHermanto4H problem with half diodes or power supply stabilization
What in the schematic
3x 10k resistors?
Hola saludos amigo. Excelente video buen proyecto te felicito. Quisiera preguntarle algo, es una duda que tengo desde hace tiempo. Es posible fabricar un controlador para un motor alternador hecho a motor. No he visto videos de alguien que haya hecho algo así. Fabricar un controlador que controle 100a
Sir please 🙏
An oscillator works if it has positive feedback but here are three MOSFET common source cascade. How can it work?
Khá hay cho dòng chân g giảm về mass để điều ap
Tanks for sharing.this circuit work for printer or copiy bldc motor
It did not work when I used same components . Are you sure it works ???
What you put below the mosfet? Is it piece of paper or any other?
in the circuit diagram there are not 3 10kohm . resistors
good job
Interesante, aunque no varía la frecuencia.
Por cierto, en el esquema te faltaron las 3 resistencias.
Hola como se podria hacer para variar la frecuencia y el ancho de estas ???
@@pierrejeanes No puedo mandar foto de esquema
@@GRIDSLER si puedes poner enlace 👍👍👍🌎
How to control singal phase bldc motor
Im not sure if a single phase bldc motor exists
СХЕМА НЕ РАБОЧАЯ НЕ ЗАМОРАЧИВАЙТЕСЬ ,МЫ ПРОСМОТРЕЛИ ЕМУ БОНУСЫ А СХЕМА ПОЛНАЯ ТУФТА ОНА НЕ РАБОчАЯ.
I love the circuit but I absolutely hate the construction method of building in space. Things could be so much more practical if made on pcb board. 👍🏼☹️
Thank you 😊😇
may i use it in my drone ..?And is that ESC heating or burning when it run with motor contuinously ..? I don't want to take any risk with my BLDC motors .
Usando 12v q hay q cambiar?
Se puede usando 5v en un motor de hdd?
В схеме не указаны где стоят резисторы 10К
Hi. for 3 wire bldc motor. do you have project ?
como é o nome desse negocio que Coloca antes do irfz44n?
Thanks for sharing bro
Would this still work if a 50k pot was used instead of the 100k?
Hey there, I have a doubt that will this circut work with the bldc motor in dvd drive . 🥺 I am looking forward for your response 😊
Will work if the motor has four wires
@@TechIdeasAG Hey, I don't know why the dvd brushless motor make weird sound and will vibrates. And the total current it take upto 1.8 amp 🥺
where is the hall sensor connected? what collor of wire? I coudn´t find the soluction for it. Could you help me?
Muy bueno... gracias por este tutorial tan interesante.
Thank you
Jab ham BLDC motor banaayenge, 3 wire hi niklegaa. Aapne ye 4th point keise nikaal diyaa motor me?
36volt ka bnaye sir g coycol ka
🙏🏼🇧🇷👍
Mr. This circuit can be use to RC motor. Thank's
Good afternoon dear, i have two questions please if i may ask, it's about the direction of the spinning can it be operated in opposite direction? And can it applicable to use a propeller on it?
The direction can easily be changed if you flip two motor wires,
And yes propeller
Thanks I appreciate
I have a hard drive motor that has only three pins instead of four, can it be useful in this project? And how to connect it to the circuit.
Can I use drone bldc motor ????
Podría usar MOSFET de menor capacidad unos 10Amp?
Porque ese motor no creo que consuma 40Amp
How Delta wired bldc motor work with this circuit????
Very nice, thanks
2:35 도면
Can it run a delta brushless motor?