YesSiRr!! Mate... your one of the BEST doing IT on RUclips with these... ONE video FULL Build from start to finish...NO CLICKBAIT, NO BullSheit, NO Mucking around Videos... Jst strait to the point & I Love it!! AGAIN...FULL BUILD, ALL IN ONE VIDEO!! Very impressive Mate... Now all we need is maybe see you actually Riding and enjoying your work... you definately Deserve & EARNED IT! Thankz for sharing Mate... take it Easy, and Stay Safe out there...
I think you should not rely on the rigidity of the plastic case. The entire system from the engine to the stern tube with shaft bearings and propeller must be on a rigid metal frame to prevent misalignment if the plastic housing is to play. As a shaft seal, it is better to use a graphite spring-loaded mechanical seal of water pumps. The engine cooling casing is aluminum - this metal will not live long in sea water, especially if the neighboring parts are made of steel - an electrolytic pair is created (school chemistry course) and aluminum is destroyed, turns into white powder. But before that, there will be active salt deposits on the cooled walls. Such a scheme of direct cooling with sea water was abandoned in the Navy. Now there is a double circuit - sea water cools fresh water, and fresh water is fed into the engine for cooling. Metal corrosion is greatly reduced.
Mantap Abangda salam kenal salam silaturahmi dari Medan Sumatera Utara Indonesia 🇲🇨🇲🇨🇲🇨 tetap semangat dan berhati-hati dalam beraktivitas sukses selalu buat channel ya,sudah dikirim bosqu paket ya,biar lebih semangat,salam kenal
There is no air in the engine and when the one contained in the table runs out it goes into a vacuum. Then with that direct exhaust you will not have enough power, you need an expansion muffler, lastly the water you inject into the exhaust does not have to enter the engine, with that pressure it is easy for it to go there.
hi guy.... multiipl slotted ring axl seals ...wider thruster tube....take a sheetmatal class.... i say 24 or 26 gauge, with some ribs and double seam at perimeter.and other spots if needed... i tell you when they start to sell you get something back...good job good luck....
Todo sellado, ante una falla en el motor hay que cortar la estructura para llegar a el. Lo mismo pasa con la hélice, queda sellada dentro del tubo yves imposible cambiar o modificar sin tener que destruir todo el sistema. Felicito la manualudad que tiene pero nada más.
Время видео: 5 минут 40 секунд. Балансировки винта не будет никакой. 7 минут. Центровки ведущего вала не будет. Гарантирую. 7 минут 13 секунд и далее. От нагрева при сварке сгорит сальник и станет мягким металл подшипника. Сальник на стороне винта необходим тоже. Иначе в подшипник попадет вода и пездетсц ему
Как и на большинстве видосов таких вот пацанчиков в шлепанцах, "самоделкиных", "реставраторов" показана какая-то шняга. Видос снятый для лайков. Для обывателя- ВАУ, из говна и палок- JETsurf, и все-бы ничего, но: где ТЕСТОВЫЙ ЗАПЛЫВ, что вообще может (если может) это корыто? Ну и, все запаковали в смолу, а движок обслуживать как? Херь полнейшая....
Great dedication on your work but I hope you're NOT polluting your local river with fiber or plastic particles. Such practice can cause cancer on people who consume fish from the surroundings. Let's keep the environment safe please.
I would recommend using RC jet boat kit. It's gonna be a bit expensive but its more quite, no exaust sytem needed and more potential on the design variation..
В названии родика говорится о проэкте водоструйной резкки, а по факту собрали что- то наподобии водомёта, который по мощности вряд ли на что то способен, кроме громкого тарахтения
Вы наверное еще "реставраторов" не смотрели!!! ))) Там жесткий диск разбирают, мылом моют, и все- РАБОТАЕТ!!! ) Не зря этот чувачок, потративший столько времени на сделать-снять, даже не показал это корыто в деле! А ему это и не надо, тут дело совсем в другом!...
With hand tools He did this!!! The second you think something is impossible…. Watch this man…. My goodness! This video makes me believe the Pyramids were build by hand! Bravo my man! The human mind is the most powerful computer on earth! Love it!
Ok this I’m interested in this one. I run IMPBA in the “B” class. Two Rossi 75. Nitro of course. One wedge with two sponsons. If it don’t do 85+ its a bad day.
ohh..metal slotted rings at axl ,...and outer case with a gear and prop set up to pump any extra water. out....then put a rubber compression reducer and clamp it when not in use..
Everything you would ever need from engineering school is all online if you have the willpower to want to learn it and dedicate yourself to teaching yourself
xin chào, tôi có một câu hỏi. Bạn có thể giới thiệu tia nước được tạo ra bằng máy in 3D trên một chiếc thuyền dài 3m với động cơ xăng 20-30 mã lực không?Hoặc nó sẽ mỏng manh, bởi vì tôi đang nghĩ đến việc mua một cái.
after making that awesome jet, you could make one of those surfboards that rise up out of the water on fins. I know you can if you can make that water jet.
hydrofoil that's it. there were fins you could bolt on outboards that got you up on plane faster, 2 of them would lift a surfboard out of the water with your jet pushing it.
YesSiRr!! Mate... your one of the BEST doing IT on RUclips with these... ONE video FULL Build from start to finish...NO CLICKBAIT, NO BullSheit, NO Mucking around Videos... Jst strait to the point & I Love it!! AGAIN...FULL BUILD, ALL IN ONE VIDEO!! Very impressive Mate... Now all we need is maybe see you actually Riding and enjoying your work... you definately Deserve & EARNED IT! Thankz for sharing Mate... take it Easy, and Stay Safe out there...
@@Z_Highlights cái vật liệu đó gọi là gi vậy a
Sounded like his motor isn't large enough to push the water. Hear it bogging? Maybe he just needs to tune carb?
This is a big help for me. And thank you for sharing this kind of project. Good job sir.
I think you should not rely on the rigidity of the plastic case. The entire system from the engine to the stern tube with shaft bearings and propeller must be on a rigid metal frame to prevent misalignment if the plastic housing is to play. As a shaft seal, it is better to use a graphite spring-loaded mechanical seal of water pumps. The engine cooling casing is aluminum - this metal will not live long in sea water, especially if the neighboring parts are made of steel - an electrolytic pair is created (school chemistry course) and aluminum is destroyed, turns into white powder. But before that, there will be active salt deposits on the cooled walls. Such a scheme of direct cooling with sea water was abandoned in the Navy. Now there is a double circuit - sea water cools fresh water, and fresh water is fed into the engine for cooling. Metal corrosion is greatly reduced.
This is a post worthy of reading straight to the point. With logic an explanation that even I can understand.
Have you really see the video?
Have you seen what this guy created?
If somebody goes you'll be your dancing shot so that's why we're here. That's wonderful. Reggae red lights are on Aubrey.
Mantap Abangda salam kenal salam silaturahmi dari Medan Sumatera Utara Indonesia 🇲🇨🇲🇨🇲🇨 tetap semangat dan berhati-hati dalam beraktivitas sukses selalu buat channel ya,sudah dikirim bosqu paket ya,biar lebih semangat,salam kenal
There is no air in the engine and when the one contained in the table runs out it goes into a vacuum. Then with that direct exhaust you will not have enough power, you need an expansion muffler, lastly the water you inject into the exhaust does not have to enter the engine, with that pressure it is easy for it to go there.
Hay quá bạn hiền ơi .👍😎😎😎👏👏👏👍 .
bạn có thể đưa trẻ em châu Á đến giai đoạn sáng tạo tuyệt vời.
PARABÉNS PELO EXCELENTE VÍDEO, SUCESSO AMIGO, UM GRANDE ABRAÇO! (PALHOÇA-SC BRASIL)
Love your designs, wish you had pdf plans for sale I would like to buy some if available, great work.
XD ku ke 1🌸🌸±⁹@9+-¢👨👨👦07⁷⁰👨👨👦0>>)))>///
Ok yg
Mesin pangkas rumput beberapa hari yang lalu di gudang rongsokan sekarang bisa di gunakan untuk papan selancar mantap punya ide
Спасибо🙏💕 за информацию🙏 так держать себя всегда✌✌✌
Very creative Hien.. Nice job, maybe you can add deskription of the material.. 👍👍👍
Rất thông minh. Chúc bạn luôn sáng tạo Ra nhiều video hay nha
Awesome Great Joy watching your mind and hands at work. No clickbait great editing with the time lapse very good job you're awesome
hi guy.... multiipl slotted ring axl seals ...wider thruster tube....take a sheetmatal class....
i say 24 or 26 gauge, with some ribs and double seam at perimeter.and other spots if needed...
i tell you when they start to sell you get something back...good job
good luck....
guy you look good ........we need more people like you.........
Ciao campione delle moto e barche 🚤 sei sei un fenomeno continua così🛳⛵️🚀🛥⛴🚢🛟🛶 ciaooo stammi bene
Bạn làm thuyền khéo tay quá
Hay quá anh Hiền ơi
Hóng phần tét vs lên màu ạ
Semangat bang 💪💪💪
Mantap hasil karyanya bisa jadi motipasi👍🤝
Teus videos são sensacionais, mas este em especial é muito bom porque está nos meus planos futuros de fazer um também.
Grande profissional, parabéns abraco aqui do BRASIL 🇧🇷👏🏻👏🏻👏🏻👏🏻👏🏻👏🏻👏🏻🇧🇷
Saludos desde Chile , Admiro mucho su GENIALIDAD.
Fomex 10mm thick PVC board
Bạn làm rất tốt
Todo sellado, ante una falla en el motor hay que cortar la estructura para llegar a el. Lo mismo pasa con la hélice, queda sellada dentro del tubo yves imposible cambiar o modificar sin tener que destruir todo el sistema. Felicito la manualudad que tiene pero nada más.
Время видео: 5 минут 40 секунд. Балансировки винта не будет никакой. 7 минут. Центровки ведущего вала не будет. Гарантирую. 7 минут 13 секунд и далее. От нагрева при сварке сгорит сальник и станет мягким металл подшипника. Сальник на стороне винта необходим тоже. Иначе в подшипник попадет вода и пездетсц ему
Пиши с цифры через двоеточие вот так 5:40, 7:13
Как и на большинстве видосов таких вот пацанчиков в шлепанцах, "самоделкиных", "реставраторов" показана какая-то шняга. Видос снятый для лайков. Для обывателя- ВАУ, из говна и палок- JETsurf, и все-бы ничего, но: где ТЕСТОВЫЙ ЗАПЛЫВ, что вообще может (если может) это корыто? Ну и, все запаковали в смолу, а движок обслуживать как? Херь полнейшая....
Anh làm video phục hồi máy từ bãi phế liệu đi a
you have the best vids on u tube,ur builds are great,,very talented.
Bạn làm rất hay nhưng động cơ bạn nên gắn bánh trớn lại để vòng tua cao hơn và có lực hơn
Tào lao. Nói nghe hay. Nhưng éo có khoa học. Tải này ko thay đột ngột ko cần bánh đà. Giảm trong lượng tăng tốc độ vòng tua cao hơn. Ngáo ah.
Great dedication on your work but I hope you're NOT polluting your local river with fiber or plastic particles. Such practice can cause cancer on people who consume fish from the surroundings. Let's keep the environment safe please.
Lol you think a man with this sort of technical skill and knowledge is that silly?
@@soloxsavage513 Yes, many times. I have seen it in Asia, Latin America and even in our own backyard. Seems you don't travel much 🤷♂️
Lol I don’t count RUclips videos as travel but do you bro
@@Boli4161 na América latina ? Países como o seu são os piores
Are you kidding me. Does the ship graveyard in India make you turn into Captain Planet Karen?
I would recommend using RC jet boat kit. It's gonna be a bit expensive but its more quite, no exaust sytem needed and more potential on the design variation..
В названии родика говорится о проэкте водоструйной резкки, а по факту собрали что- то наподобии водомёта, который по мощности вряд ли на что то способен, кроме громкого тарахтения
Вы наверное еще "реставраторов" не смотрели!!! ))) Там жесткий диск разбирают, мылом моют, и все- РАБОТАЕТ!!! ) Не зря этот чувачок, потративший столько времени на сделать-снять, даже не показал это корыто в деле! А ему это и не надо, тут дело совсем в другом!...
Корпус закрыт - т.е. двигатель не нужно обслуживать? А бутылку с бензином к ноге будет скотчем приматывать? И в итоге ничего и никуда не поплыло.....
Это КИДАЛОВО, посмотрите еще таких-же "реставраторов"!!!
Wow... amazing idea 💡! i like your video 📸📸
Awesome project. I would like to know what kind of glue .
Totally me in my shop. I only use a ruler or caliper when needed. Most fabrication I do is via eyeballing it.
With hand tools He did this!!! The second you think something is impossible…. Watch this man…. My goodness! This video makes me believe the Pyramids were build by hand! Bravo my man!
The human mind is the most powerful computer on earth! Love it!
Well information. Good show.
hey........joe !, good deal, thank you for the school...... can now build a big jet drive ! .
Ok this I’m interested in this one. I run IMPBA in the “B” class. Two Rossi 75. Nitro of course. One wedge with two sponsons. If it don’t do 85+ its a bad day.
Tuyệt vời OK
Exelente trabajo saludos desde Ecuador
em chờ video nay từ bữa giờ
ohh..metal slotted rings at axl ,...and outer case with a gear and prop set up to pump any extra water. out....then put a rubber compression reducer and clamp it when not in use..
This guy it’s very very good like he have 100 years experience you can see how it’s handle the grinder and etc very good my friend you legend
Такие ребята никогда не пропадут. Свой кусок хлеба всегда заработают. )))
cach cac chau che rat la hay
Động cơ xăng này mua ở đâu vậy bác, giá bảo nhiêu? Thank bác
That is really cool! I have a 3D printed jet unit you can have if you want it would work with that motor
hi DK T Ldr, can you please send me drawing of jetpump or propeller with dimension for my wooden jetski using 125cc motorcycle engine?
Good job just one motor brushless nunber 65161 top speed boat 🤙
the fuel is gonna dissolve that pvc intake manifold. lol.
Hay quá anh , chạy rất nhanh
"Thanh cong! Yeu no." 👍
Mi problema no entender si son motores comunes adaptados enfriamento al agua..
Es posible un motor de moto enfriamento agua de Rio ..
Very impressive Sir!
You amaze me with this incredible work . Did you go to an engineering school ?
Everything you would ever need from engineering school is all online if you have the willpower to want to learn it and dedicate yourself to teaching yourself
@@thepeoplesupdates676 that sir is even more impressive
@@BadlydrawnBen been teaching myself physics and mechanical engineering for 12 years now. Going damn good so far
@@thepeoplesupdates676 it certainly is I have been showing my friends your video's all the engineers want to employ you 👍
Bộ jet (không động cơ) có làm bán không bạn!
THANKIOU
Hay lắm
Cho mình hỏi tí,bộ này chạy máy dầu Kubota có được không ạ
friend I congratulate you for the projects you do, I ask you what material is the target you use to make the boat?
làm bằng moto điện ok hơn á a
Poor guy has used that drill bit till the very end , very much respect.
Dear friend!
How will you service the engine?
Cho mình hỏi động cơ đó bao nhiêu cc? Bạn lấy từ máy gì vậy???
nice design! but it need more power! maybe twin engine is enough.
công nhận ông giỏi thiệt
A hiền ơi miếng nhựa để làm bản vẻ phần khung đó tên gì mua ở đâu vậy a hiền
what kind of materials are you using?
Mấy cái tấm trắng trắng đó Gọi LÀ gì vậy anh
Great skill to made water jet
For me, you are the Greatest🎉!! Witch Phantasie!
xin chào, tôi có một câu hỏi. Bạn có thể giới thiệu tia nước được tạo ra bằng máy in 3D trên một chiếc thuyền dài 3m với động cơ xăng 20-30 mã lực không?Hoặc nó sẽ mỏng manh, bởi vì tôi đang nghĩ đến việc mua một cái.
Mấy miếng vậy liệu anh ghép khung máy lướt sóng là gì em quên rồi
No humans were harmed during the production of the project…
Miếng mà lót với keo gì để lắp lên thân ván là gì vậy a
Hydrofoils, cut the friction so much that you will double or even gain more then double the speed.
Please please wear goggles when fiberglassing the resin got in my eye. It was bad permanently. I love the creatively
after making that awesome jet, you could make one of those surfboards that rise up out of the water on fins.
I know you can if you can make that water jet.
Bagus sekali tangan anda sangat creative
Браво Маньяки 👍😂🔨🚓😱
Молодец! Но надо мощный мотор от 10 hp
Да, мощности не достаточно, а так найс 👍
Chế cano cánh ngầm đi a
Не голова, а проектная мастерская. А расчёты,цифры, чертежи, макеты. У нас это называется пяп-ляп, на авось.
Tấm màu trắng là gì vậy bạn. Keo gián mua ở đâu được bạn.
Keo sợi bạn vùng miền tây ra tiện tạp hoá mua nhiều lắm
Very nice! Good job!
Can you tell me what motor you using, I'm not familiar😅, I want to make it too
A chế củ đề đi a
All this video to show how you build it but nothing to see how it works?👎🏻
Nice vlog
hydrofoil that's it. there were fins you could bolt on outboards that got you up on plane faster, 2 of them would lift a surfboard out of the water with your jet pushing it.
Very good job
Did it work ? Think you need atleast 80cc to 110cc engine high rev engine. Seen many attempts, seems that's maybe only a 50cc engine? How many cc
900 really, everything is sealed. hard to repair, integrate gas tank
I tried looking for that material over here but they don't carry it the big box store. Where can I get it do you have a link
900 giờ?bốc phét ít thôi,quen thói
ถ้าทำเป็นไฟฟ้าแจ๋วเลย
Xin chào, tôi có thể tìm thấy vật liệu màu trắng mà bạn dùng để làm khuôn thuyền ở đâu