i have seen different videos' in RUclips,videos that done by different professionals ,but No one is explain like you, thank you so much i have seen your videos that you have launched on you tube, all videos were so crucial/core or very important to professionals, so continues line this...
I'm getting a bit lower voltage when measuring between +(-) and AC 0.49V (isn't it supposed to be double?). When measuring +(negative lead) to AC i'm getting 0.52V. Where does that 0.49V come from? IT should be 0.9V I measured it in circuit btw.
When tested diode onboard I got reading +563 but upon changing ends it read +1350. It only occured on 3 diodes closely onboard induction cooker but other diodes seem perfectly ok. Is the diodes ok or other component onboard are at fault.
@@electronicsrepairbasics_erbOk, I should have mentioned I am testing it on a circuit board. I have test another one on the board and when I put the black and red prongs on the middle pins~ it also beeps.
Hello, when I measure between + and - (reverse polarity) I do not have a double voltage drop ( 1 V) but 0.5 V only. Could it be the reason for the PC monitor not working?
Exactly I'm not getting double reading from one end to another end and rest of the things are matching with your explanation. Then is this bridge rectifier defective?
are you lowering the pitch of your voice in post processing? either that or there's something wrong with your mic..jeez ..sounds like an electronics tutorial from the underworld
![I.N "HALLUCINATION" | [Stray Kids : SKZ-PLAYER]](http://i.ytimg.com/vi/n5B5q1Hwt_U/mqdefault.jpg)
i have seen different videos' in RUclips,videos that done by different professionals ,but No one is explain like you, thank you so much i have seen your videos that you have launched on you tube, all videos were so crucial/core or very important to professionals, so continues line this...
Wow, thank you!
Your presentation is extremely helpful. Thanks
Glad it was helpful!
Good, simple and direct explanation. Kudos.
Thank you for your explanation, excellent video. Many thanks to you.
Glad it was helpful!
Thanks for the knowledge. But please sir can you do a video on how to test the smd bridge rectifier used in mobile chargers?
Is that analog multimeter or the digital one?
Best video ever
Very helpful thank you
Glad it was helpful!
I'm getting a bit lower voltage when measuring between +(-) and AC 0.49V (isn't it supposed to be double?). When measuring +(negative lead) to AC i'm getting 0.52V.
Where does that 0.49V come from? IT should be 0.9V
I measured it in circuit btw.
When tested diode onboard I got reading +563 but upon changing ends it read +1350. It only occured on 3 diodes closely onboard induction cooker but other diodes seem perfectly ok. Is the diodes ok or other component onboard are at fault.
Its Ok
@@electronicsrepairbasics_erb Thank you.
When testing a 4 pin bridge rectifier, should i get a beep in continuity mode when only testing the two midlde pins ~ ?
No, no beep bro, any beep means failed
@@electronicsrepairbasics_erbOk, I should have mentioned I am testing it on a circuit board.
I have test another one on the board and when I put the black and red prongs on the middle pins~ it also beeps.
🙏🙏🌹🌹Thanks
You’re welcome 😊
Hello, when I measure between + and - (reverse polarity) I do not have a double voltage drop ( 1 V) but 0.5 V only. Could it be the reason for the PC monitor not working?
Yes Bro it could be
I have the bang same problem mate, was your rectifier still within the circuit or was reading taken when the component was removed ?
thanks ❤❤
You're welcome 😊
Thanx all video 🥰🥰
Thank you too
if i dont get double rating but get exact same does that mean its bad?
Hi Emil,
No, the only case that we can say that the bridge is failed is when you get a continuity ( buzzer ).
Oh thank you for your response
Exactly I'm not getting double reading from one end to another end and rest of the things are matching with your explanation. Then is this bridge rectifier defective?
@@kironsk7697that’s exactly what I’m getting. Good numbers except no double reading on the end.
Oh, and yea, I’m getting continuity, so it’s bad. Thanks
I was hoping he would show reading of bad ones.
Bad ones will be shorted
are you lowering the pitch of your voice in post processing? either that or there's something wrong with your mic..jeez ..sounds like an electronics tutorial from the underworld
NONE of mine double 😆