Thank you so much! I didn't know how to change the light bulb on my old machine, but thanks to you I have replaced it with a beautiful, better LED light! You have also helped me with other things! Thank you!!
The video is not old, the sewing machine is quite old, the bobbin holder should be as shown in the video. Do you have a problem with your sewing machine, we are here to try to help.?
I have a few Viking 6030’s. One I just bought from a secondhand store was sent to me seized. Would this information also apply to the 6000 series machines?
NO, the Husqvarna Viking 6000 sewing machine series has a completely different shuttle hook, nothing is the same, it is an older series of machines. www.masinskikutak.com/2022/03/vintage-husqvarna-viking-sewing-machine.html
There are no screws, I used a fingernail on my left hand and pulled the plate towards me and then you lift it up, if you can't with a fingernail then use a thin screwdriver. ruclips.net/video/sek0-DziI-0/видео.htmlsi=QuZ3PETP8K9TK8Jv&t=77
I didn't understand the question very well, maybe you think that the position of the needle can be changed?? The answer is Yes, set the selector to the first position A on the upper side and adjust the position of the needle with the inner ring for zigzag width.
Maybe someone installed a stronger light bulb, buy an LED light bulb and you won't have problems with heating. And be careful not to cut yourself, the light bulb can break if it has not been removed for a long time, and especially if it has been heated a lot, it can be as if glued.!! 24:04
Hey, would you happen to know where to buy replacement parts? I am looking for that bobbin cover plate right at the beginning of the video. We have the exact same machine too, but when I look online some supplies refer to the S250, my machine only says 250 electronic on it. Is that the same model?
You probably mean the bobbin cover,? Husqvarna Viking S250 and Husqvarna Viking 250 Electronic, I really don't know what the difference is, it's probably a matter of powering the machine's motor, dimensions and number of programs, they are identical sewing machines, but I'm not sure.
Special narrow pliers are needed to take out the rest of the bulb or remove the plastic shield, if this is too much work for you visit your nearest sewing machine service, it is a routine job for a handyman, it shouldn't cost much. NOTE: before any work on the sewing machine, disconnect the machine from the power supply.!!
This sewing machine model has a specific bobbin and it is difficult to install a different one, see the bobbins offer on our aBay: www.ebay.com/usr/masinskikutak
Su modelo es similar a este modelo del video solo en el nombre, todo lo demás es completamente diferente, recomendado por el manual de servicio: www.masinskikutak.com/2022/03/vintage-husqvarna-viking-sewing-machine.html
Thank you so much! I didn't know how to change the light bulb on my old machine, but thanks to you I have replaced it with a beautiful, better LED light!
You have also helped me with other things! Thank you!!
Thank you so much. Helpful video!
Thank you for watching and sharing our videos 🙂
ruclips.net/video/b7X8p29I4pg/видео.html
I realize this video is a tad old but that bobbin holder is it supposed to be loose or does it need to be locked tight in the tray?
The video is not old, the sewing machine is quite old,
the bobbin holder should be as shown in the video.
Do you have a problem with your sewing machine, we are here to try to help.?
Thank you very much
Thank you very much, your video was very helpful to me😊
I have a few Viking 6030’s. One I just bought from a secondhand store was sent to me seized. Would this information also apply to the 6000 series machines?
NO, the Husqvarna Viking 6000 sewing machine series has a completely different shuttle hook, nothing is the same, it is an older series of machines.
www.masinskikutak.com/2022/03/vintage-husqvarna-viking-sewing-machine.html
@@MasinskiKutak thank you!
How did you get that metal plate off, mine won't budge, did you unscew something?
There are no screws, I used a fingernail on my left hand and pulled the plate towards me and then you lift it up, if you can't with a fingernail then use a thin screwdriver.
ruclips.net/video/sek0-DziI-0/видео.htmlsi=QuZ3PETP8K9TK8Jv&t=77
Can the needle be adjusted side to side on this machine?
I didn't understand the question very well, maybe you think that the position of the needle can be changed??
The answer is Yes, set the selector to the first position A on the upper side and adjust the position of the needle with the inner ring for zigzag width.
Is it possible to turn off the lightbulb when the machine is on?
It is not possible if you have one switch, if the light bothers you, unscrew the bulb.
@MasinskiKutak thanks, ill take it out, for me it feels like it heats stuff up too much
Maybe someone installed a stronger light bulb, buy an LED light bulb and you won't have problems with heating.
And be careful not to cut yourself, the light bulb can break if it has not been removed for a long time, and especially if it has been heated a lot, it can be as if glued.!! 24:04
Yup, i was verry confused for a couple minutes there, it felt like it would never budge, but i managed to get it out
Hey, would you happen to know where to buy replacement parts? I am looking for that bobbin cover plate right at the beginning of the video. We have the exact same machine too, but when I look online some supplies refer to the S250, my machine only says 250 electronic on it. Is that the same model?
You probably mean the bobbin cover,? Husqvarna Viking S250 and Husqvarna Viking 250 Electronic, I really don't know what the difference is, it's probably a matter of powering the machine's motor, dimensions and number of programs, they are identical sewing machines, but I'm not sure.
When pulling out the lightbulb, the Stuck inside the sewing machine. How do I take it apart to remove it?
The cap from the lightbulb. (the lightbulb did not remove completely.) I only got the bulb part.
What's left inside, the complete bulb or the metal part in the bulb socket?
ruclips.net/video/b7X8p29I4pg/видео.html
Special narrow pliers are needed to take out the rest of the bulb or remove the plastic shield, if this is too much work for you visit your nearest sewing machine service, it is a routine job for a handyman, it shouldn't cost much.
NOTE: before any work on the sewing machine, disconnect the machine from the power supply.!!
Why can’t I get mine to ZIG ZAG!?! It sews a straight stitch beautifully!
What machine model do you have, what about the other sewing programs, do the other programs work.?
May iuse the other kind of spool
This sewing machine model has a specific bobbin and it is difficult to install a different one, see the bobbins offer on our aBay:
www.ebay.com/usr/masinskikutak
Hola tengo una maquina de cocer VIKING Husqvarna modelo 64 30 ,se hace bolas el hilo de abajo y no avanza
Su modelo es similar a este modelo del video solo en el nombre, todo lo demás es completamente diferente, recomendado por el manual de servicio:
www.masinskikutak.com/2022/03/vintage-husqvarna-viking-sewing-machine.html