I had to take a grinder at both ends and take some off each side. Works perfect now. It would not come off without doing this. Yes as Eric says loosen the bolt but that is some frig to do every time you switch. Also.. Did yours come with the adjustable ends?? I had to purchase after sale when I saw that option on the cab model. Dealer told me it was cab model option only. They are a must for all 3 ph on any tractor in my opinion. Just have to get it close to one side and the other usually adjusts so both pins hook up in one stop.Without those your looking at 3-4 times or more I have seen on and off tractor and a little back and a little front,,,,wow so much easier with those adjustable ends. If your looking for them anyone, ask for B3030 3ph adjustable arms kit.
Very informative video. It looks like you have a bolt over that rod which mounts the draft arms. Does it hold the rod in place? If you loosened it, could you slide the rod back and forth to increase your clearance for removing the arms?
Hi, we are in the process of buying the same tractor and found your channel.Is that the stock 3 point hitch I should be looking for I have seen other tractor videos with a ratcheting sleeve . Not sure if that is an option . We will have the same subframe backhoe setup with a cab so I want to make sure we get the 3 point hitch system that is supposed to come with the tractor when they deliver .love your vids new subscriber here. thanks
also looking for a 3 point hitch for my kubota b2650. Went to 2 kubota dealers. didnt know how to order it. Go figure, I dont underestand, this is there job. Help me out anybody if you can. Email address gigi1976@protonmail.com Thank you
Unfortunately, my subframe was attached prior to sliding that pin in at all. (By the dealer) Anyone know of any other method to get that long pin in? Thank you.
You're going to want to pull that plate off anyway so you can confirm tightness. Dealer didn't properly tighten a bunch of stuff as it turns out. Tighten things ;)
Do you remember the size of the snap ring pins you replaced on the stabilizers My tractor is 60 miles away and i’d like to stop at TS and get some on the way
That rear isn't anything like my L2501. I was thinking they would be closer to each other both being Kubota, and close to size. You have a vent tube, and a dipstick. Mine doesn't have either, but mine has a sight glass. Your fill plug is black, and mine is red. The upper arms, and top link are the same. The lower arms, the way the lower arms attach, and lower arm adjustment is not the same.
Followed this video to installed the 3pt hitch on my B2650 yesterday. Incredibly helpful and succinct. Thank you.
What 3 point kit is this
Otherwise lossen the bolt under the pto stump and slide the long pin from left to right....
I had to take a grinder at both ends and take some off each side. Works perfect now. It would not come off without doing this. Yes as Eric says loosen the bolt but that is some frig to do every time you switch.
Also.. Did yours come with the adjustable ends?? I had to purchase after sale when I saw that option on the cab model. Dealer told me it was cab model option only. They are a must for all 3 ph on any tractor in my opinion. Just have to get it close to one side and the other usually adjusts so both pins hook up in one stop.Without those your looking at 3-4 times or more I have seen on and off tractor and a little back and a little front,,,,wow so much easier with those adjustable ends. If your looking for them anyone, ask for B3030 3ph adjustable arms kit.
I got the adjustable ends as an option with the tractor. I knew I would need them.
Very informative video. It looks like you have a bolt over that rod which mounts the draft arms. Does it hold the rod in place? If you loosened it, could you slide the rod back and forth to increase your clearance for removing the arms?
Yes, you can slide the rod back and forth if you loosen the bolt.
Hi, we are in the process of buying the same tractor and found your channel.Is that the stock 3 point hitch I should be looking for I have seen other tractor videos with a ratcheting sleeve . Not sure if that is an option . We will have the same subframe backhoe setup with a cab so I want to make sure we get the 3 point hitch system that is supposed to come with the tractor when they deliver .love your vids new subscriber here. thanks
also looking for a 3 point hitch for my kubota b2650. Went to 2 kubota dealers. didnt know how to order it. Go figure, I dont underestand, this is there job. Help me out anybody if you can. Email address gigi1976@protonmail.com Thank you
Unfortunately, my subframe was attached prior to sliding that pin in at all. (By the dealer)
Anyone know of any other method to get that long pin in?
Thank you.
You're going to want to pull that plate off anyway so you can confirm tightness. Dealer didn't properly tighten a bunch of stuff as it turns out. Tighten things ;)
Do you remember the size of the snap ring pins you replaced on the stabilizers
My tractor is 60 miles away and i’d like to stop at TS and get some on the way
That rear isn't anything like my L2501. I was thinking they would be closer to each other both being Kubota, and close to size. You have a vent tube, and a dipstick. Mine doesn't have either, but mine has a sight glass. Your fill plug is black, and mine is red. The upper arms, and top link are the same. The lower arms, the way the lower arms attach, and lower arm adjustment is not the same.
I looked at the L2501 before getting my B2650. The L2501 is significantly larger that the B2650. I wouldn't expect much to be similar.