Sure it is! I may do that on my own KP3S in this way, too. This printer I use will be used for more tutorials, that's why I put the cable outside. Thanks for your advise!
This is a very helpful video, I just got a KP3S and will be doing this mod. However, the "Translation" had me laughing pretty good. "So everything works perfectly".
The main question is what use is the autolevel?, if in the end the bed does not move and only the nozzle moves when it touches the bed or print parts and unscrews. It would then be like adding another thing to adjust instead of helping, it creates another problem because you always have to adjust the bed to the nozzle and then adjust the autolevel. I really don't see the point.
Hello, I have a kp3s pro s1, I connected the cables like here to the z+, but with homing the z axis goes up, I changed the direction of homing and going down, but without the active bl Touch is there any way to do it in the configuration, do I have to connect bltouch to z-?
I have several kp3s pro printers and I'm really looking forward to when you release a tutorial for it! At least firmware and text instructions. I would be very grateful.
Anyone Having trouble with KP3S and 3D Touch on Marlin. READ THIS SOLVED: I fixed it. So if you happen to see or hear anyone having issues with the KP3S and 3d Touch with Marlin... Send them my way. Or simply tell them that the video Kingroon puts out tells you to put the 3d touch 2 pin into the Z+ slot... Thats incorrect.. You actually need to unplug the stock Z endpoint sensor from the Z- Slot and then plug the 3D touch into that one. Then all of the calibrated builds for Marlin on git hub.. Will work with the 3D Touch and the extruder will move in the correct direction during probe wizard and everything else
Flash made no difference to my Kp3s v3, 3d touch has both led's lit but theres no update/change to the screen so it still dont work. Mines got the GD32f303 chip and the download was for that model but nothing changed once the flash loaded.
@@schellmax Ive taken mine off, It takes under 2 minutes to set it by hand with a 1.5 feeler gauge and the print sticks 95% of the time. I just watch the first couple of layers until the fans fire up then go make a cup of coffee and bash Tinkercad for my next print.
Mine returns to the center point and start going down a bit after completing the autolevel, and has a Z offset tab, but needs different values for printing, ie: need a -2.11 offset when using the autolevel, but at printing needs a -2.31, if i keep that last digit, when completing auto level, the nozzle will be crushed on the bed, any tips??
i spent a day trying to get this to work, but failing. it turns out it won't do the firmware update if using some sd card adaptors. also, i tried the new z offset firmware that's in the drive link, but it has issues with skipping gcode and doing invisible or floating prints
Please send videos to show the problem, our guy will try their best to help you out. The address is support@kingroon.com. As for skipping gcode, it might not be supported yet. Thanks!
I installed this, and when trying to home z, the probe doesn't do anything. I have made sure to use your firmware that was made for the KP3S Pro. I followed your instructions, and when try to bed level, the print head goes all the way right.
if I follow instructions for Kp5L, will it work with KP3S?. For KP5L I must perform manual level first, then install bltouch and perform autolevel, with KP5L its not necessary to modify configuration file. Thanks for your answer
@@vitormaichberger4057 Not yet, we are quite busy with the sales peak season. It’s still in development. But we will let the engineers know and make it sooner.
I have a problem. Kingroon kp3s Motherboard 1.3 based on GD32F303. I connected everything, checked the pinout of the wires several times, everything corresponds to the video. The firmware installed normally. But when 3D Touch is connected, the printer does not turn on... i.e. I press the power button and nothing happens. The OS does not boot. If I turn off the sensor, then everything works, the printer boots, I can even turn on autolevel (but if the sensor is turned off, this makes no sense). What could be the problem?
Boa noite, minha impressora está aquecendo o bico de impressão sem controle, ultrapassando os 300 graus alguns segundos após ligá-la, você pode me ajudar? Posso te enviar um vídeo por e-mail se você quiser.
Please send an email with a video that can show the problem to support@kingroon.com, our guy will help you out soon. Before that you can also check all the limit switches and cables, see if there is anything wrong with them. Thanks!
I am trying to implement this on my kp3s pro with killper firmware, I follow this tutorial but I don't know the pin number of the mcu, so I can't config it.
Yes, but we haven't release the firmware yet. It will be available soon. You can also post for help in our Facebook group, some guy may have figured out how to use it with Marlin. facebook.com/groups/kingroon3d/
Hey, just wanted to know if the values for the autolevel were saved even when the KP3s is turned off? Do I need to autolevel each time I do a print? Thanks! Tutorial was clear and fixed my warped bed problem!
@@Kingroon3DOfficial Where is the new tutorial? in thw website still have 2022 info. it would be useful a document guide to do this in "OEM firmware" provide by you
You can install them together, but not using together. But actually not suggest to, because it will make the print head heavy and affect the print quality.
It's about the KP5L. After the firmware, the emoticons disappear and only small letters come out. This isn't just me, but many people are asking this question all the time. How do I solve it?
Please let us know which is the firmware you mentioned, trying flashing back to the stock firmware see if the problem solved. Please also check my reply on your other two comments. We are now in a long holiday, the reply might be late. I will remind the engineers of your email and ask for a reply. Hopefully we can help you out as soon as possible. Thanks!
Not sure about it. The 407 mainboard is quite different from the 303 and 103. We still some time to build a complete new firmware with this feature for it.
Move the heat bed towards you, then you will find a label with a serial number. You should be able to find “103” “303” or “407” in it. Or you can simply flash the firmware, if failed, it’s a 407 mainboard.
when i put in the sd card to flash the tft update it say it 100% complete but the progress bar dosent move even a bit and now when i boot up my printer without the sd card it just booting forever and never stops
Hello, I have problems with the extruder since I updated the firmware. The bltouch does not work, on the screen I do not see self-leveling, only leveling, it does not start printing if I do not connect it to the computer although it reads the card and tells me that the printing begins without heating neither the nozzle nor the bed. There is some solution, because I have tried with the latest firmwares for bl touch and without it and it does not work. Thank you. Hola, tengo problemas con la extrusora desde que actualizó el firmware. El bltouch no funciona, en la pantalla no veo autonivelación, solo nivelación, no empieza a imprimir si no lo conecto al ordenador aunque lee la tarjeta y me dice que la impresión comienza sin calentar ni la boquilla ni la cama. Hay algo de solución, porque he probado con los últimos firmwares para bl touch y sin él y no funciona. Gracias.
According to user’s feedback, bl touch is not supported with this firmware. Please flash back to the stock firmware or replace the bl touch with a 3D Touch. Thanks!
After installing the firmware, when giving autoleveling the tip of the sensor stays up and in each of the 9 points of the autoleveling the Z axis goes up a little more (and I have to turn it off because otherwise the printer will be disassembled ) I have the KP3S v3 and I don't know what to do, pls help.
If you get the 3D Touch too close to the build plate, please check the video first, make sure you have install the box in the right place. By right place I mean leaving one block above. Then you need to go modify the txt file, add the z offset value. The default value should be -2.8, you can try modify it to -1.8. Once you find a rough value, adjust the value 0.1 once a time. After that you should be fine. If too far, just do the opposite. We know its tricky and troublesome, but the new firmware is going to be published soon with the offset wizard.
@@Kingroon3DOfficial I installed the firmware with the Z offset and when Im leveling everithing goes ok. At the moment of starting the impression, it is like no offset was configured. What could be the problem?
Does anybody else have a problem when after selecting auto leveling printer just go to 0, and then to the center of the bed and doesn't move or use 3D touch? 3D touch is moving after you turn the printer on, so it definetely work.
Same here. I tried different firmware from different people, different tutorials, and different cable configurations. I even installed Klipper on the printer with no luck. 😢 So, please let me know if you found any fix.
@ I don’t know what you already tried, but try to check if your pinout is correct. Because mine 3D Touch had a + and - swapped in the 3-pin cable. It didn’t help me anyway, but maybe in your case this is what cause problems. And people in KP3S group chat also told me to check if i’ve connected everything properly.
KP5L is no problem and we will release the firmware for it. But KP3 may not be OK to use it. We will let people know the results if we run any tests on it.
Help me please. I connected bl touch according to the instructions, when turned on, the stem extends up and down and lights up red. when i press auto level it retracts the stem, lights up red, goes to autolevlel but the stem does not extend! and nothing happens when it closes.
Please send us an email with the video, we will check it and find the problem out. Please make sure the video shows all the operating you make. Our email address is support@kingroon.com And you can add”For Frank” in the subject. My coworker will let me know in the first time.
@@Kingroon3DOfficial Thanks for the quick response, I sent the question by mail, I will also leave a link to the video here. ruclips.net/video/iP_fLnxw-68/видео.html
We will let the technical team know, see if they can make one. Since KP3 are different from KP3S on mainboard, it would be another project. Before that, we suggest you try Marlin firmware, it should work. Hope my answer helps you well. Happy 3D printing.
I followed all the instructions and it broke my printer. It will not auto level. It tries to move as far right as possible and the stepper motor will grind. I installed original firmware and it will not do manual bed level now. The printer will not go to the correct location of all 5 bed leveling points, it will just go to the wrong location, and the motor will grind. I sent you a video on facebook messenger. My printer is now bricked.
Try unplugging the 3d touch sensor, I have the same problem, the program flashes correctly, but when I hit the auto-level the printer maxes out on the x axis an the motor binds. What I do to return to the original configuration with manual leveling is to unplug the sensor and reboot the printer.
@Gustavo Martinez I honestly got fed up with their unprofessional customer support, and no response from their support email. I sent the machine back. I'm buying a prusa mini instead.
OMG THIS DOESNT WORK.. How are you guys selling both your printers and 3d touch and don't support people when it comes to installing it. I just bought the printer from you and Im about to throw it out the F**&&&ING window..... I FOLLOWED YOUR STEPS EXACTLY... I EMAILED YOU.. I POSTED COMMENTS ON YOUR PAGE... AND IM NOT GETTING ANY RESPONSES...... Please do an updated video or address peoples problems.. because I am seeing that most comments of people having issues are the exact same as mine and you guys dont seem to care at all
Then it’s high likely that your printer is using the 407 chip and not compatible with the firmware. Please download the stock firmware and flash it back: drive.google.com/file/d/1L0blIRQVKSnWLjHYZfrcu6rVo_yLhVFZ/view?usp=sharing
@@Randomperson0467 Just download the file, unzip it, then copy all the files in the folder to your SD card, then put the SD Card into the printer and reboot it.
Hello Kingroon support. I have emailed you but I am posting this for the benefit of other people that may have the same issue: On Kingroon KP3S with STM32F103 chip I have added BLTouch V3.1. I followed the instructions, wired it correctly, flashed the firmware. When printer is powered on Bltouch does its probe check just fine. It goes up and down 3 times. But, when I hit auto leveling button it does not extend the probe. I can hear Z switch clicking as it homes, and Bltouch probe is still retracted. What could be causing this? Does Z switch causing the issue? Should Z switch still be connected? Or, is it something else?
Do you have any 3D Touch? If you do please try with it. Please also ask the seller, see if it works in 5V. According to the video, your BL Touch is under voltage.
@@Kingroon3DOfficial I have Bltouch, not 3d touch. How do I make it work on 5v? I know that my bltouch does work on other printer with 5v. Is there some other setting that I can try or is this re-cabling issue??
@@Kingroon3DOfficial I tried flipping the 3 pin plug but the result is the same. My connections are correct. I am guessing that there is maybe something in firmware that needs to be changed. Maybe the config file/firmware has to issue a signal to deploy the probe? I am willing to try out the beta firmware, if you want me to test it out.
That sounds weird, we double checked that link but found no such issue. Please try change your internet or use a VPN. If still not work, please send an email to support@kingroon.com. Thanks!
That's a ridiculous and cumbersome way of setting your z offset. Has anyone got marlin or Klipper working on this thing? Its mostly a good design for the price accept for the lack of a belt tensioner on X and y. I would probably buy a couple printers is it had belt tensioner. Klipper could be figured out I guess.
You are now watching the old video. Please check the video we posted last Sunday, new firmware has already released with the Z offset wizard. Marlin, Klipper and auto bed leveling is only for extension of the printer. They are not the features everyone needs. And for stability concerns, we currently not add them as default. It’s not a good way to raise the prices for adding features. But we definitely will make tutorials on those features, let our customers to decide to use them or not, and add some new features as default in our future models. The feature we add must be stable enough. Thanks!
Ok so what's the point of it all. It does not auto level, it just gives a user more problems. Instead of calibrating the bed level once with a sheet of paper, a user also has to calibrate the auto-leveling tool with such a quirky way, nice logic. LOL. It dose not move the bed it does nothing useful but adding additional steps to the default manual calibration.
You haven't noticed that you are watching an earlier tutorial with old version firmware, have you? The current ABL sensors are not so powerful as you thought, that's why I recommend a basic manual level first. Anyway, this tutorial and firmware is going to be updated to the third version. If you need to try that feature out, please find the second version first.
I put a 3d touch on kingroon kp3s. The nozzle was too close to the table. I started adjusting the height by changing the value as shown in the video. I put the value 50 at the end, but nothing helped. What to do in such a situation?
![Blox Fruits Dragon Rework Update [Full Stream]](http://i.ytimg.com/vi/EqDAp8udhm0/mqdefault.jpg)
![[Устарело] BLTouch. Стоит ли покупать? Установка, прошивка, калибровка. На примере Tevo Tornado](/img/1.gif)
It's perfectly possible to use the existing cable shield to route the 3d touch cable instead of using zip ties. Way more cleaner that way.
Sure it is! I may do that on my own KP3S in this way, too. This printer I use will be used for more tutorials, that's why I put the cable outside. Thanks for your advise!
This is a very helpful video, I just got a KP3S and will be doing this mod. However, the "Translation" had me laughing pretty good. "So everything works perfectly".
LOL, thank y ou for watching
It's perfect, the most annoying thing is calibrating this printer and this update improves the only negative point of this printer
Can we pleeeease get firmware for the KP3S Pro that has babystepping supported.
will this apply to kp3s pro s1 as well ?
I want to know that too
Eu também quero saber.
Да, но нужно корректировать направление оси Х и размеры стола в файле configuration.h
Why does it only come with two screws not four?
Hi! Great video! I follow all but when i press autolevel,the hotend goesmake only a "home". Maybe do you know why? Thank you
The main question is what use is the autolevel?, if in the end the bed does not move and only the nozzle moves when it touches the bed or print parts and unscrews.
It would then be like adding another thing to adjust instead of helping, it creates another problem because you always have to adjust the bed to the nozzle and then adjust the autolevel.
I really don't see the point.
Hello, I have a kp3s pro s1, I connected the cables like here to the z+, but with homing the z axis goes up, I changed the direction of homing and going down, but without the active bl Touch is there any way to do it in the configuration, do I have to connect bltouch to z-?
saya mengalami hal yang sama, apakah sudah ketemu jalan keluarnya?
I have several kp3s pro printers and I'm really looking forward to when you release a tutorial for it!
At least firmware and text instructions.
I would be very grateful.
did you find any tutorial for the kp3s pro?
@@SupernovaGD I have the problem auto home go opacity
Anyone Having trouble with KP3S and 3D Touch on Marlin. READ THIS
SOLVED:
I fixed it. So if you happen to see or hear anyone having issues with the KP3S and 3d Touch with Marlin... Send them my way. Or simply tell them that the video Kingroon puts out tells you to put the 3d touch 2 pin into the Z+ slot... Thats incorrect.. You actually need to unplug the stock Z endpoint sensor from the Z- Slot and then plug the 3D touch into that one. Then all of the calibrated builds for Marlin on git hub.. Will work with the 3D Touch and the extruder will move in the correct direction during probe wizard and everything else
Does it also work with klipper?
No Idea. I just know its with marlin@@fatt0nk171
How could I manage that in some models the calibation nozzle is colliding with the printing part?
Hello, can we use diy bltouch of optical endstop and servo motor to this kingroon kp3s ??
Can you guys upload a detailed tutorial for marlin and 3d touch. I cant seem to get it to work
hello, this is not for marlin, just support klipper
Es posible en una KP3 ??
Sorry, my 3D Touch stays always RED and dont does the autolevel as seen... just touches at Z home and stops in standby
В мене також…(
Flash made no difference to my Kp3s v3, 3d touch has both led's lit but theres no update/change to the screen so it still dont work. Mines got the GD32f303 chip and the download was for that model but nothing changed once the flash loaded.
same problem!!
@@schellmax Ive taken mine off, It takes under 2 minutes to set it by hand with a 1.5 feeler gauge and the print sticks 95% of the time. I just watch the first couple of layers until the fans fire up then go make a cup of coffee and bash Tinkercad for my next print.
Mine returns to the center point and start going down a bit after completing the autolevel, and has a Z offset tab, but needs different values for printing, ie: need a -2.11 offset when using the autolevel, but at printing needs a -2.31, if i keep that last digit, when completing auto level, the nozzle will be crushed on the bed, any tips??
What adapter do I use with the original kp3s?
I have successfully followed this steps to install 3dtouch.
but Klipper is not connected, is this method not supported for Klipper ?
Could please add z probe offset in the firmware ui. So its easier to find right one
Sure! Actually we are now testing the firmware with that feature. It will be published once it is ready.
@@Kingroon3DOfficial thank you
@@doodle4532 you’re welcome!
@@Kingroon3DOfficial This is going to be so helpful. I appreciate you guys taking community feedback so strongly. Very excited thank you!
@@kol101101 You are welcome!
It works on Pro S1???
is kp3s pro can?
i spent a day trying to get this to work, but failing. it turns out it won't do the firmware update if using some sd card adaptors.
also, i tried the new z offset firmware that's in the drive link, but it has issues with skipping gcode and doing invisible or floating prints
Please send videos to show the problem, our guy will try their best to help you out. The address is support@kingroon.com. As for skipping gcode, it might not be supported yet. Thanks!
on the v1.3 kp3s the j16 port is where the tc port is in the video where should i plug in the wire??
Same as the video do.
@@Kingroon3DOfficial but in video j16 is where the j17 port is on my printer
I installed this, and when trying to home z, the probe doesn't do anything. I have made sure to use your firmware that was made for the KP3S Pro. I followed your instructions, and when try to bed level, the print head goes all the way right.
Do they actually have firmware for the KP3S Pro? It doesn't show any in this tutorial.
@thewonderwaffleofficial Yeah, just type in Google.
Please, where is the file to the 3D model so that I may print one? Thanks
You can find it in the firmware files
if I follow instructions for Kp5L, will it work with KP3S?. For KP5L I must perform manual level first, then install bltouch and perform autolevel, with KP5L its not necessary to modify configuration file. Thanks for your answer
the wire that plug into z plus port keep falling off. any suggestion?
Is this tutorial for non 3.0 version models only?
No, as long as your KP3S has a main board ends with 103 or 303.
Having to reflash to set z offset sounds pretty awful. Are there any plans to make this a feature that can be adjusted on the printer?
We will publish a newer firmware to make it happen. Is has been made and still under testing. I think it would be soon.
@@Kingroon3DOfficial has it already launched?
@@vitormaichberger4057 Not yet, we are quite busy with the sales peak season. It’s still in development. But we will let the engineers know and make it sooner.
This is a must.
@@madrian_hello sure
Do you have a link to print the 3d touch cover as demonstrated in the video?
it is in the files
@@Mario29615what files?
@@briandenley the project files...
I have a problem. Kingroon kp3s Motherboard 1.3 based on GD32F303. I connected everything, checked the pinout of the wires several times, everything corresponds to the video. The firmware installed normally. But when 3D Touch is connected, the printer does not turn on... i.e. I press the power button and nothing happens. The OS does not boot. If I turn off the sensor, then everything works, the printer boots, I can even turn on autolevel (but if the sensor is turned off, this makes no sense). What could be the problem?
HI I hope you solved it, 6 months later 😀 What was the problem ?
is the sensor touch leveling compatible with KP3S PRO ?
Sure, but we haven't release the related firmware yet. It will be available with new tutorial soon.
@@Kingroon3DOfficial where?
Does this work with Kipper?
yes
Tôi sửa phần sụn không có tác dụng, không có gì khác biệt xảy ra sau khi nạp phần sụn
I keep trying to change the Z probe offset in the config file and it doesn’t seem to be changing anything. Thoughts?
Please check the newer video of this, you are using the earlier version of the firmware. ruclips.net/video/LBa8X6U1Y_w/видео.html
el firmware con z offset me da muchos errores alguna nueva version ?
After the instalation, when I start to print, the printer just dont work and starts to make a noise like bip. Does anyone know how to fix it?
Boa noite, minha impressora está aquecendo o bico de impressão sem controle, ultrapassando os 300 graus alguns segundos após ligá-la, você pode me ajudar? Posso te enviar um vídeo por e-mail se você quiser.
Any way to do one with filiment run out sensor.
The same, they use different ports. We will do tutorials for those models, too.
@@Kingroon3DOfficial update?
@@doodle4532 The new firmware is still in testing. Once it is ready, we will release it.
Question, suddenly my kp3s printed only the half of its size on the front left side. Need help!
Please send an email with a video that can show the problem to support@kingroon.com, our guy will help you out soon. Before that you can also check all the limit switches and cables, see if there is anything wrong with them. Thanks!
Where is the KP3S PRO S1 firmware?
STL mount for 3d touch KP3S
kingroon.com/blogs/downloads/kingroon-kp3s-bltouch-installation
@@Kingroon3DOfficial Não tem, apenas um diferente do vídeo. Não teria como disponibilizar um igual ao vídeo ?
if i want to switch back to manual levelling , what should i set?
Just flash the stock firmware. And you can keep the 3D Touch installed. Once you change your mind, just flashing the firmware to enable it.
Onde consigo o arquivo do suporte do 3d touch apresentado no vídeo ?
I am trying to implement this on my kp3s pro with killper firmware, I follow this tutorial but I don't know the pin number of the mcu, so I can't config it.
The same pin as the KP3S do. You will need to change the configuration to use it.
can i use for my kp3s pro?
Yes, but we haven't release the firmware yet. It will be available soon. You can also post for help in our Facebook group, some guy may have figured out how to use it with Marlin. facebook.com/groups/kingroon3d/
Can z offset be set via gcode commands? I know there is no tft option but hoping that still is
No, it can’t. But we’ll see if we can make that happen. We are now testing a new firmware with a z probe wizard.
@@Kingroon3DOfficial This is so exciting to hear and can't wait to test.
@@kol101101 Thanks for the patience! We will make it sooner.
@@Kingroon3DOfficial any updates on firmware? 🙂
@@FNGecko It is still in test. We will publish it both here and our Facebook groups as soon as we finish it.
Hey, just wanted to know if the values for the autolevel were saved even when the KP3s is turned off? Do I need to autolevel each time I do a print? Thanks! Tutorial was clear and fixed my warped bed problem!
Please check the newer tutorial, you are looking at the first version, there would be a third version soon. We had new features in the second version.
@@Kingroon3DOfficial Where is the new tutorial? in thw website still have 2022 info. it would be useful a document guide to do this in "OEM firmware" provide by you
infelizmente não funciona
Can the 3D touch autolevel and laser engraver be used together?
You can install them together, but not using together. But actually not suggest to, because it will make the print head heavy and affect the print quality.
It's about the KP5L. After the firmware, the emoticons disappear and only small letters come out. This isn't just me, but many people are asking this question all the time. How do I solve it?
Please let us know which is the firmware you mentioned, trying flashing back to the stock firmware see if the problem solved. Please also check my reply on your other two comments. We are now in a long holiday, the reply might be late. I will remind the engineers of your email and ask for a reply. Hopefully we can help you out as soon as possible. Thanks!
407 soon???
Not sure about it. The 407 mainboard is quite different from the 303 and 103. We still some time to build a complete new firmware with this feature for it.
How do I know which chip I have? Do I have to take the bottom off?
Move the heat bed towards you, then you will find a label with a serial number. You should be able to find “103” “303” or “407” in it. Or you can simply flash the firmware, if failed, it’s a 407 mainboard.
when i put in the sd card to flash the tft update it say it 100% complete but the progress bar dosent move even a bit and now when i boot up my printer without the sd card it just booting forever and never stops
Make sure your mainboard is end with 103 or 303. It usually happens when the mainboard doesn’t fit.
@@Kingroon3DOfficial no it is a 303
Is it the same as kp3s pro （ upgraded Y-axis with linear rail) ? thanks
No, it is different on firmware. You can connect the pins on the motherboard side and leave the other side unconnected and wait for the new firmware.
@@Kingroon3DOfficial Thanks
@@Kingroon3DOfficial But can you tell me how long to wait for the firmware?
Can I proceed in the same way for Kp3s Pro?
Yes, you do, but we haven’t released the firmware yet. There would be problems if you flashed the KP3S Firmware. We will release it soon.
@@Kingroon3DOfficial soon?
What screwdriver did you use to remove the bottom plate of the printer?
It should be M2.5. If you still keep the official tool box, we have it included. It’s in a small bag.
@@Kingroon3DOfficial Thanks! For me I used a 2mm and it still worked.
@@dextutorials8201 You are welcome!
Hello, I have problems with the extruder since I updated the firmware.
The bltouch does not work, on the screen I do not see self-leveling, only leveling, it does not start printing if I do not connect it to the computer although it reads the card and tells me that the printing begins without heating neither the nozzle nor the bed.
There is some solution, because I have tried with the latest firmwares for bl touch and without it and it does not work.
Thank you.
Hola, tengo problemas con la extrusora desde que actualizó el firmware.
El bltouch no funciona, en la pantalla no veo autonivelación, solo nivelación, no empieza a imprimir si no lo conecto al ordenador aunque lee la tarjeta y me dice que la impresión comienza sin calentar ni la boquilla ni la cama.
Hay algo de solución, porque he probado con los últimos firmwares para bl touch y sin él y no funciona.
Gracias.
According to user’s feedback, bl touch is not supported with this firmware. Please flash back to the stock firmware or replace the bl touch with a 3D Touch. Thanks!
After installing the firmware, when giving autoleveling the tip of the sensor stays up and in each of the 9 points of the autoleveling the Z axis goes up a little more (and I have to turn it off because otherwise the printer will be disassembled ) I have the KP3S v3 and I don't know what to do, pls help.
If you get the 3D Touch too close to the build plate, please check the video first, make sure you have install the box in the right place. By right place I mean leaving one block above. Then you need to go modify the txt file, add the z offset value. The default value should be -2.8, you can try modify it to -1.8. Once you find a rough value, adjust the value 0.1 once a time. After that you should be fine. If too far, just do the opposite. We know its tricky and troublesome, but the new firmware is going to be published soon with the offset wizard.
@@Kingroon3DOfficial I installed the firmware with the Z offset and when Im leveling everithing goes ok. At the moment of starting the impression, it is like no offset was configured. What could be the problem?
depois que coloquei o arquivo a impressora inverteu os sentidos do x e y e também esta demorando para iniciar a impressão. o que fazer ?
máy in của tôi lúc bắt đầu autolevel cũng bị ngược trục x k thể level được, bạn đã làm cách nào để xử lí nó vậy?
Does anybody else have a problem when after selecting auto leveling printer just go to 0, and then to the center of the bed and doesn't move or use 3D touch? 3D touch is moving after you turn the printer on, so it definetely work.
Same here. I tried different firmware from different people, different tutorials, and different cable configurations. I even installed Klipper on the printer with no luck. 😢 So, please let me know if you found any fix.
@ I don’t know what you already tried, but try to check if your pinout is correct. Because mine 3D Touch had a + and - swapped in the 3-pin cable. It didn’t help me anyway, but maybe in your case this is what cause problems. And people in KP3S group chat also told me to check if i’ve connected everything properly.
does anyone have profile for kingroon KP3S for either Cura, Simplify3d and/or Prusa slicer?
в куре уже есть профиль
è possibile installare il sensore sulla KP3 oppure sulla KP5L ?
KP5L is no problem and we will release the firmware for it. But KP3 may not be OK to use it. We will let people know the results if we run any tests on it.
Help me please. I connected bl touch according to the instructions, when turned on, the stem extends up and down and lights up red. when i press auto level it retracts the stem, lights up red, goes to autolevlel but the stem does not extend! and nothing happens when it closes.
Please send us an email with the video, we will check it and find the problem out. Please make sure the video shows all the operating you make. Our email address is support@kingroon.com And you can add”For Frank” in the subject. My coworker will let me know in the first time.
@@Kingroon3DOfficial Thanks for the quick response, I sent the question by mail, I will also leave a link to the video here. ruclips.net/video/iP_fLnxw-68/видео.html
@@vladimirkrivosheev3920 Thanks for the video! I will try to help you out soon.
@@vladimirkrivosheev3920 Hi, I have a question. What’s the version of your BLtouch? A product link would be helpful, thanks!
@@Kingroon3DOfficial this is bltouch v3 from trinaglelabs link sent to email
can you add one to the KP3?
We will let the technical team know, see if they can make one. Since KP3 are different from KP3S on mainboard, it would be another project. Before that, we suggest you try Marlin firmware, it should work. Hope my answer helps you well. Happy 3D printing.
I followed all the instructions and it broke my printer. It will not auto level. It tries to move as far right as possible and the stepper motor will grind. I installed original firmware and it will not do manual bed level now. The printer will not go to the correct location of all 5 bed leveling points, it will just go to the wrong location, and the motor will grind. I sent you a video on facebook messenger. My printer is now bricked.
Try unplugging the 3d touch sensor, I have the same problem, the program flashes correctly, but when I hit the auto-level the printer maxes out on the x axis an the motor binds. What I do to return to the original configuration with manual leveling is to unplug the sensor and reboot the printer.
@Gustavo Martinez I honestly got fed up with their unprofessional customer support, and no response from their support email. I sent the machine back. I'm buying a prusa mini instead.
Same thing right now:( Did you manage to fix it?
Hi!
Have you found a soluce for this problem. i have the same thing with my KPS3 pro😞
OMG THIS DOESNT WORK.. How are you guys selling both your printers and 3d touch and don't support people when it comes to installing it. I just bought the printer from you and Im about to throw it out the F**&&&ING window..... I FOLLOWED YOUR STEPS EXACTLY... I EMAILED YOU.. I POSTED COMMENTS ON YOUR PAGE... AND IM NOT GETTING ANY RESPONSES...... Please do an updated video or address peoples problems.. because I am seeing that most comments of people having issues are the exact same as mine and you guys dont seem to care at all
7:53 my printer did not reboot
Then it’s high likely that your printer is using the 407 chip and not compatible with the firmware. Please download the stock firmware and flash it back: drive.google.com/file/d/1L0blIRQVKSnWLjHYZfrcu6rVo_yLhVFZ/view?usp=sharing
@@Kingroon3DOfficial how do I do that
@@Randomperson0467 Just download the file, unzip it, then copy all the files in the folder to your SD card, then put the SD Card into the printer and reboot it.
@@Kingroon3DOfficial ok
저 3d 케이스는 어디서 구할수 있나요?
It’s is in the firmware files. Link is the description.
Hello Kingroon support. I have emailed you but I am posting this for the benefit of other people that may have the same issue:
On Kingroon KP3S with STM32F103 chip I have added BLTouch V3.1.
I followed the instructions, wired it correctly, flashed the firmware.
When printer is powered on Bltouch does its probe check just fine. It goes up and down 3 times.
But, when I hit auto leveling button it does not extend the probe.
I can hear Z switch clicking as it homes, and Bltouch probe is still retracted.
What could be causing this? Does Z switch causing the issue? Should Z switch still be connected?
Or, is it something else?
Do you have any 3D Touch? If you do please try with it. Please also ask the seller, see if it works in 5V. According to the video, your BL Touch is under voltage.
@@Kingroon3DOfficial I have Bltouch, not 3d touch. How do I make it work on 5v? I know that my bltouch does work on other printer with 5v. Is there some other setting that I can try or is this re-cabling issue??
@@zeeman2594 Please try turning the three pin cable 180 degrees then connect to the port, see if the red light turns off.
@@Kingroon3DOfficial I tried flipping the 3 pin plug but the result is the same. My connections are correct. I am guessing that there is maybe something in firmware that needs to be changed. Maybe the config file/firmware has to issue a signal to deploy the probe? I am willing to try out the beta firmware, if you want me to test it out.
@@zeeman2594 Thanks for your reply! We will let the engineer know and see what to do next.
the drive wont let me download
That sounds weird, we double checked that link but found no such issue. Please try change your internet or use a VPN. If still not work, please send an email to support@kingroon.com. Thanks!
@@Kingroon3DOfficial I changed browsers and that worked. Thank you for responding.
@@doodle4532 You are welcome!
감사합니다. 덕분에 잘 사용하고 있습니다.
You're welcome😁❤
>release the extended cable
>package comes with 2 screws yet tutorial uses 4
That's a ridiculous and cumbersome way of setting your z offset. Has anyone got marlin or Klipper working on this thing?
Its mostly a good design for the price accept for the lack of a belt tensioner on X and y. I would probably buy a couple printers is it had belt tensioner. Klipper could be figured out I guess.
You are now watching the old video. Please check the video we posted last Sunday, new firmware has already released with the Z offset wizard. Marlin, Klipper and auto bed leveling is only for extension of the printer. They are not the features everyone needs. And for stability concerns, we currently not add them as default. It’s not a good way to raise the prices for adding features. But we definitely will make tutorials on those features, let our customers to decide to use them or not, and add some new features as default in our future models. The feature we add must be stable enough. Thanks!
ну все на соплях )))
я просто в ахуе сейчас) прикрутил на kp3s pro, нихуя не работает, инфы никакой нет... принтер мечта просто
Ok so what's the point of it all. It does not auto level, it just gives a user more problems. Instead of calibrating the bed level once with a sheet of paper, a user also has to calibrate the auto-leveling tool with such a quirky way, nice logic. LOL. It dose not move the bed it does nothing useful but adding additional steps to the default manual calibration.
You haven't noticed that you are watching an earlier tutorial with old version firmware, have you? The current ABL sensors are not so powerful as you thought, that's why I recommend a basic manual level first. Anyway, this tutorial and firmware is going to be updated to the third version. If you need to try that feature out, please find the second version first.
I put a 3d touch on kingroon kp3s. The nozzle was too close to the table. I started adjusting the height by changing the value as shown in the video. I put the value 50 at the end, but nothing helped. What to do in such a situation?