The days of wheel acid may finally be coming to an end. This stage of high end paint correction is an absulute must before compounding etc. The FACT that it won't discolor wheels nor trim is invaluable to both pros and hoobyists alike. Only draw back is the heavy sulfur aroma...but thats a 1st world problem.
I polished my car after I clayed bar. I focused mainly on the hood And it brought back the shine, however the black spots stayed. I'd appreciate the help. Thx
What’s the difference between this and Meguiar’s Ultimate All Wheel Cleaner? I have 2 bottles of UAWC and would like to know if it’s also safe to use to that to decontaminate the paint. It says it’s ph balanced and turns purple too. Seems like the same stuff to me?
@@valkyrie_voodoo could you please elaborate on that or explain how they’re different. Is it not safe on the paint? I’ve been holding out using it on paint because I’m just not sure about that…
What if this gets onto rusty parts of a panel? Planning on doing full paint correction on my old truck, but some panels have rust along the bottom and around wheel wells. What will happen when this drips down onto the rusty parts of the panels?
The product is recommended to use at full strength. We have not heard of it being diluted. The performance of this product could be affected depending on how much dilution you intend to use.
My car is 6 years old I just did this today and still not finished . I kept some spray bottle with only water nearby. Every time I hit a trim with iron remover I sprayed it off with the water bottle right away. The trim was ok afterwards. Also my trim has Armor all trim protection, so maybe that helped too.
I like these iron decon videos, they are strangely satisfying :) Whenever I can, I show their effects too on my channel. There are a few brands that are less stinky (some are actually even pleasant, like Bilt Hamber's and Nanolex's), but some are like rotten eggs (Eagle One, Chemical Guys Iron Decon).
If doing a full detail, yes, as it would help to start with a fully decontaminated paint prior to polishing and doing paint correction. Recommended to do an iron remover once a year or so.
First 🤙Meguiar's iron decon does not blacken unpainted raw aluminum ?? , because all wheel cleaner had a little darkness on my unpainted brake calipers! . Are there materials to avoid with iron decon? thank you in advance
Very/Extremely similar - Meguiar's Mirror Bright Wheel Cleaner Iron X is by far more shelf stable... So use the Meguiar's and don't store it long as it goes bad and wont work.
@@carlosherrera8541 not to cut in on the video but from the research I've just done since posting, best thing to do is either use iron decontaminate product and then follow up with water and vinegar mix on the glass. Other people are using a glass polish compound but I'll personally try the iron contaminate remover and water vinegar mix. Some also recommend clay barring your car.
They are both part of the chemical decontamination phase, which should be done before the mechanical decontamination phase with clay. You should only clay if needed, and only if you are going to polish afterwards as claying will leave fine scratches.
@@BlackHawkPSU The megs failed to work at all at a year and it was never opened when i opened it to use. I found an old gallon of ironx in my garage that was open and worked no problem and was 3 years old. Garage temp stays between 50 & 80 degrees.
Hi guys do I clay bar before I use the iron remover or do I use the iron remover first ? Car was left in storage in a dusty warehouse and it’s now covered in dust that won’t come off with a wash
Andrew Reichel good question, ive been using Beadmaker a synthetic sealant while drying and then i tried Hyper seal a Sio2 sealant. The paint was not slick anymore and beading was poor. So i then tried a Powerful APC and it became worse. Even after two washes with Reset to remove any residue. Ive since used Opti’s power clean twice and my detailer tried twice with a light clay and IPA wipe with little luck. Starting to think something went wrong with install of the coating.
What brand of coating is it, when was is applied, who applied it, how long ago was it applied, was is applied by a professional detailer in a enclosed environment, was the clear coat prepped properly before applying,is the coating 2yr 5yr warranty??? Those are the questions I would like answers to get a better understanding of your coating issues.
Ok I guess doing the coating outside may have been the issue here. Still have unanswered questions from you but the installer should answer. My biggest concern is why would a certified installer apply a ceramic coating outside??? Not supposed to do that for possible airborne contamination plus there is a 24 hour cure time etc? Smh
Besides Ironx , Megs Iron decon is the best. People complain about rotten egg smell from Megs Iron remover compared to others. Who cares??? Get over it
![Seungmin "그렇게, 천천히, 우리(As we are)" | [Stray Kids : SKZ-PLAYER]](http://i.ytimg.com/vi/kAzmhLHePqU/mqdefault.jpg)
Finally a video that describes the decon process thoroughly! Thank you!
You are so welcome!
The days of wheel acid may finally be coming to an end. This stage of high end paint correction is an absulute must before compounding etc. The FACT that it won't discolor wheels nor trim is invaluable to both pros and hoobyists alike. Only draw back is the heavy sulfur aroma...but thats a 1st world problem.
Thumbs up! You answered most of my questions about chemical decontamination.
Thank you so much! I was so confused on when to use the iron remover
What about inside glass?
I polished my car after I clayed bar.
I focused mainly on the hood
And it brought back the shine, however the black spots stayed. I'd appreciate the help. Thx
Those are probably tar deposits. You can get a tar and sap remover that desolves it and you can wipe them off.
How often should you decon (chemical and mechanical) a daily driver car?
Probably every 3 to 6 months don’t do it regularly it could** do paint damage if left on the car
I like the quick detail+ no wax. it has stated clean almost 1 month. .
It's important to polish after claying, otherwise you will most likely mar the paint.
Majority of the time you will polish after claying but if you use a fine clay bar marring is greatly reduced.
Speed master clay mitt will almost be guaranteed to mar you’re paint.
What’s the difference between this and Meguiar’s Ultimate All Wheel Cleaner?
I have 2 bottles of UAWC and would like to know if it’s also safe to use to that to decontaminate the paint. It says it’s ph balanced and turns purple too. Seems like the same stuff to me?
Same stuff
@@freddyj5845 Thanks Freddy!
@@nickb5091 not the same stuff
@@valkyrie_voodoo could you please elaborate on that or explain how they’re different. Is it not safe on the paint? I’ve been holding out using it on paint because I’m just not sure about that…
What if this gets onto rusty parts of a panel? Planning on doing full paint correction on my old truck, but some panels have rust along the bottom and around wheel wells. What will happen when this drips down onto the rusty parts of the panels?
Can i use this on plastic fairings of motorcycles?
This might be a stupid question but is it safe on PPF (xpel)
Can you use it as clay lub
Is this a bit like traffic film remover or spray alloy wheel cleaner. Looks like a pretty similar product?
Wow great explanation from guys that know what a heck iron remover is and does tnks n blessings
Hello, i used by mistake in a self wash the wheel foam on my car paint ...but i rince it a few minutes later....do You think it damaged my paint?
Yep, you basically have to get it repainted.
Can Meguiar's Wheel & Paint Iron Decon - Gallon be diluted. The back label says “Ready to Use.” Has anyone tried diluting?
The product is recommended to use at full strength. We have not heard of it being diluted. The performance of this product could be affected depending on how much dilution you intend to use.
Safe for plastics trim???
My car is 6 years old I just did this today and still not finished . I kept some spray bottle with only water nearby. Every time I hit a trim with iron remover I sprayed it off with the water bottle right away. The trim was ok afterwards. Also my trim has Armor all trim protection, so maybe that helped too.
Spray anywhere on exterior.
I like these iron decon videos, they are strangely satisfying :) Whenever I can, I show their effects too on my channel. There are a few brands that are less stinky (some are actually even pleasant, like Bilt Hamber's and Nanolex's), but some are like rotten eggs (Eagle One, Chemical Guys Iron Decon).
Bilt hamber stinks horrible
@@johndavies4644 The Korrosol stinks, but the Auto-wheel is OK. At least for me, but we can all have different opinions.
Using the iron removal spray is it necessary?
If doing a full detail, yes, as it would help to start with a fully decontaminated paint prior to polishing and doing paint correction. Recommended to do an iron remover once a year or so.
First 🤙Meguiar's iron decon does not blacken unpainted raw aluminum ?? , because all wheel cleaner had a little darkness on my unpainted brake calipers! . Are there materials to avoid with iron decon?
thank you in advance
I hope the next step in this is making a foam cannon formula.
Is this pretty much the same product as their all wheel cleaner
Very/Extremely similar - Meguiar's Mirror Bright Wheel Cleaner
Iron X is by far more shelf stable... So use the Meguiar's and don't store it long as it goes bad and wont work.
Great video! After viewing, I just subscribed.
Can u use this if u have bonnet graphics on your car. Thank u
Yes
Will this help take off the old water rain spots??
OMG I was about to ask this question!!!
My car on the side glass has stubborn watermark rain spots that do not come off even with glass cleaner and methylated spirits.
@@changereception7750 I got that same issue on my truck and I can’t seem to get it off but ima going to try some brand of iron remover.
@@carlosherrera8541 not to cut in on the video but from the research I've just done since posting, best thing to do is either use iron decontaminate product and then follow up with water and vinegar mix on the glass. Other people are using a glass polish compound but I'll personally try the iron contaminate remover and water vinegar mix. Some also recommend clay barring your car.
Clay bar the glass and use a 3m type soft scrub pad to agitate the stain but be careful it isn't harsh enough to scratch the glass surface.
How's the smell for this product?
Rotten eggs
Iron remover and Tar remover. Are those uses for same purpose?
One is for iron the other for tar...
They are both part of the chemical decontamination phase, which should be done before the mechanical decontamination phase with clay. You should only clay if needed, and only if you are going to polish afterwards as claying will leave fine scratches.
Is it safe for plastic
Did you ever see if it was safe?
How does this compare to iron x
Iron X is by far more shelf stable... So use the Meguiar's and don't store it long as it goes bad and wont work.
@@ToddTinley Curious as to where that information comes from? I'd like to check that out.
@@BlackHawkPSU The info comes from me buying bulk of both products and my user experience.
@@ToddTinley Thanks for the reply. How long would you say that Megs lasts after opened vs Iron X? Thanks!
@@BlackHawkPSU The megs failed to work at all at a year and it was never opened when i opened it to use. I found an old gallon of ironx in my garage that was open and worked no problem and was 3 years old. Garage temp stays between 50 & 80 degrees.
Hi guys do I clay bar before I use the iron remover or do I use the iron remover first ? Car was left in storage in a dusty warehouse and it’s now covered in dust that won’t come off with a wash
You use iron decon first then clay bar to save you time
Awesome, thanks guys.
does this remove wax etc from paint?
No it shouldn't.
Has anyone tried this in a pump sprayer?
good video on cleaning.
Can you use this on the windows???
Yes, but don't let it dry.
Is this can be use as bug and tar cleaner?
No
Smells like raw sewage but God dammit dose it work. I go through about 5 gallons a month at my shop.
Do you do this before a wet sanding ???
yes
I need something that will strip everything off my Ceramic coating.
why? what's wrong with it?
Andrew Reichel good question, ive been using Beadmaker a synthetic sealant while drying and then i tried Hyper seal a Sio2 sealant. The paint was not slick anymore and beading was poor. So i then tried a Powerful APC and it became worse. Even after two washes with Reset to remove any residue. Ive since used Opti’s power clean twice and my detailer tried twice with a light clay and IPA wipe with little luck. Starting to think something went wrong with install of the coating.
What brand of coating is it, when was is applied, who applied it, how long ago was it applied, was is applied by a professional detailer in a enclosed environment, was the clear coat prepped properly before applying,is the coating 2yr 5yr warranty??? Those are the questions I would like answers to get a better understanding of your coating issues.
Andrew Reichel yes to most, opti coat by a certified installer. It was done outside .. most are these days with the mobile detailers.
Ok I guess doing the coating outside may have been the issue here. Still have unanswered questions from you but the installer should answer. My biggest concern is why would a certified installer apply a ceramic coating outside??? Not supposed to do that for possible airborne contamination plus there is a 24 hour cure time etc? Smh
Can this be diluted
he said its ready to go out of the bottle so no dilution
How many mikes were there at Meguiars? Mike Phillips, Mike stoops, mike Pennington. Rumours that meguiars was owned by 3M may be true!!!
Besides Ironx , Megs Iron decon is the best. People complain about rotten egg smell from Megs Iron remover compared to others. Who cares??? Get over it