Great video, I have all the same Lock and Access Control System. And I had all the same problems, as I could not program it by their own instructions, and I could not read the tiny instructions. Thanks so much this has been a great help.
We are using a system like this for a science fair project. How do you get power to it without hardwiring in? We won’t actually be installing it anywhere, just using it for the experiment. How is it being powered for your video?
Hmmmm. So can you change that programming "master code"? Because as presented anyone can just type #999999#1 and program an RFID key fob/card, then use that to freely open the door!
you can make this a lot more secure by adding a wiegand access controller to this, it will interface with the keypad, now if people want in they'd have to have (or steal) credentials
Hello there I need some help I have the same power supply and mag lock that's in the video I'm installation it on my gate the drive way is about 100 feet long from the house when ever I try to ring the door bell from the gate it doesn't ring and the mag locking force is weak the wire am using is CAT 5 and the power supply is in the living 5AMP power supply am using!
It's cool, but imo it was safer if the keycode box was mounted in wall and wiring was accessible only from the other side (inside the office), so that you couldn't break the keycode loose and rewire it - you would have to then break down the wall itself, but at that point you'd just break down the doors instead. Meanwhile, from inside, you could just open up a metal panel mounted in wall and get access to the wiring
So what's up with the power? It's just two red wires..nothing sets them apart to know what's hot and neutral..I just hooked it up the way you said but I get a blinking light on the power supply
When i connect my magnetic lock to mine, it just beeps and the keypad is unresponsive. The moment i unplug it is fine. I cant see that there is a short circuit. I get a good 12v output when the lock is armed so i cant see why connecting a magnetic lock makes it faulty. Any ideas?
I am not sure if there is a complete kit with all of the components in it, but you can find them all on AliExpress Magnet: www.aliexpress.com/item/4000382082121.html Keypad: www.aliexpress.com/item/32673908668.html Power Supply: www.aliexpress.com/item/32763536883.html Door Exit Button: www.aliexpress.com/item/32949198370.html
I am not sure if there is a complete kit with all of the components in it, but you can find them all on AliExpress Magnet: www.aliexpress.com/item/4000382082121.html Keypad: www.aliexpress.com/item/32673908668.html Power Supply: www.aliexpress.com/item/32763536883.html Door Exit Button: www.aliexpress.com/item/32949198370.html
Hello Sir. Can i please ask you to show or send me the Link, to buy one of this kits, to myself. Like you say Sir, I Wish i had one of this , long ago. Please help me out. Thank you also for sharing your work. Im very thankfull for that.
This seems to be the current model now: www.amazon.com/Weatherproof-Control-Electric-Magnetic-110VPower-x/dp/B071X6LFFS/ref=sr_1_4?ie=UTF8&qid=1542816530&sr=8-4&keywords=ip65+electronic+magnetic+lock
Save yourself a TON of money and just buy each component individually on AliExpress. The kit on amazon is way overpriced for the same components. Currently as of Feb 15, 2020 the following items are only $78.34 USD The kit on amazon is $100 more expensive. Magnet: www.aliexpress.com/item/4000382082121.html Keypad: www.aliexpress.com/item/32673908668.html Power Supply: www.aliexpress.com/item/32763536883.html Door Exit Button: www.aliexpress.com/item/32949198370.html
Maybe I have a different instructional book, mine says to open the back of the machine shell, (I'm assuming that means the transmitter? ) and then connect to the power supply...I don't see how this thing connects to the power supply..everything else is going great though. I bought it for my camper lol. A little tricky with the door. So anyway, maybe I'm interpreting it wrong.
Bro, can you just lay it out for me pls? I've had the unit apart, the transmitter apart, I don't see where I can connect anything to it...can you just write a brief step by step? I'd really appreciate it if you could do that, if you can afford the time to do so..thank you in advance
try this 1 its the same but with fingerprint access www.ebay.co.uk/itm/Fingerprint-RFID-Card-Access-Control-System-280kg-Magnetic-Lock-2Remote-Controls-/142746386558?_trksid=p2349526.m4383.l4275.c10
This link worked as of 3/2019: www.ebay.com/itm/620-LBs-Kit-Electric-Door-Lock-Magnetic-Access-Control-ID-Card-Password-System/171841317313?ssPageName=STRK%3AMEBIDX%3AIT&_trksid=p2060353.m2749.l2649
i know this is an old video but just to let you know if some one uses a screw driver to take the screw off the bottom of the keypad they can just join the common and normally open wire together and the door will unlock for them
@@Lesscoelectronics phew! glad to hear this, I use speaker wire for 120V all the time! I figure it's beefier than lamp wire you can get and its just copper right?! Thanks for all your videos Martin, you helped me through my first remote start install many years ago. You're kinda nuts posting your phone number here though ;)
Well I'll do it anyway. I hope that's ok with you. FYI look up what car audio wire ratings are and the latest china man wire, You may be suprused what you find. Don't get hung up on labels..
The lock in normal situations will just not work with a loss of AC power, However a nut like me tie it into their security system's backup battery/inverter, So I never lose power.
This system is not International Building and Fire Code compliant. This system is super unsafe please do not use this video as a guide unless you want to incur fines for violating fire code.
![Noob To Max With DRAGON REWORK In Blox Fruits [FULL MOVIE]](http://i.ytimg.com/vi/LnBMOinoOvA/mqdefault.jpg)
thanks for share
Great video, I have all the same Lock and Access Control System.
And I had all the same problems, as I could not program it by their own instructions, and I could not read the tiny instructions.
Thanks so much this has been a great help.
Can i get a clear shot of that wiring diagram?
We are using a system like this for a science fair project. How do you get power to it without hardwiring in? We won’t actually be installing it anywhere, just using it for the experiment. How is it being powered for your video?
Hmmmm. So can you change that programming "master code"? Because as presented anyone can just type #999999#1 and program an RFID key fob/card, then use that to freely open the door!
Alex Marin yes
Does anywhere tell you how to change the master code?
nice job. does the door stay locked if the power goes out?
no, it would be the opposite, if the magnet looses power, the door is open
Very helpful. Thank you!
You're welcome!
Great job .... thanks
Thank you!
Will the security door be compromised if the key pad got vandalized ?
yes, you can open this system by shorting 2 wires on the keypad together
you can make this a lot more secure by adding a wiegand access controller to this, it will interface with the keypad, now if people want in they'd have to have (or steal) credentials
Is there a way to wire it so you don't need the keypad? I am looking for a solution with a pushbutton enter/pushbutton exit. Thanks!
How do I reset it during a power outrage
is it possible to connect two RFID Readers in parallel?
Hello there I need some help I have the same power supply and mag lock that's in the video I'm installation it on my gate the drive way is about 100 feet long from the house when ever I try to ring the door bell from the gate it doesn't ring and the mag locking force is weak the wire am using is CAT 5 and the power supply is in the living 5AMP power supply am using!
can you put the power supply closer to the lock instead?
@@Lesscoelectronics ok am going to try that and see what happens
It's cool, but imo it was safer if the keycode box was mounted in wall and wiring was accessible only from the other side (inside the office), so that you couldn't break the keycode loose and rewire it - you would have to then break down the wall itself, but at that point you'd just break down the doors instead. Meanwhile, from inside, you could just open up a metal panel mounted in wall and get access to the wiring
So what's up with the power? It's just two red wires..nothing sets them apart to know what's hot and neutral..I just hooked it up the way you said but I get a blinking light on the power supply
Hi, I bought the keyboard, I would like to connect the bell button to do it works but I can not, what wires and how should I do? thank you
Hello what wire did you use for this please and how did you wire it to the mains please?
I used heavy insulated car audio speaker wire and cat8 to extend the data cables
hi, I'm going crazy to get the bell to attack, but does it work? how can I do?
When i connect my magnetic lock to mine, it just beeps and the keypad is unresponsive. The moment i unplug it is fine. I cant see that there is a short circuit. I get a good 12v output when the lock is armed so i cant see why connecting a magnetic lock makes it faulty. Any ideas?
How can I get this all accessories easily and from where
Thank you
I am not sure if there is a complete kit with all of the components in it, but you can find them all on AliExpress
Magnet: www.aliexpress.com/item/4000382082121.html
Keypad: www.aliexpress.com/item/32673908668.html
Power Supply: www.aliexpress.com/item/32763536883.html
Door Exit Button: www.aliexpress.com/item/32949198370.html
How did you setup delay??
the module has a variable potentiometer built in that you can turn up or down.
were you located less if i need some work done
Hello.
To connect a rfid reader to a mag lock? What do I need?
A power supply and a the reader connected to the mag lock? Or is there something else?
The rfid receiver is needed, Mine is built in the keypad outside.
May I ask how many locks can the controller handle at the time and how many lock can the power supply handle at the same time?
Different kits will vary, All I can tell you is this kit I worked on is a single door not designed to be linked with an external unit.
Is it possible to connect two rfid readers in parallel? ( for magnetic lock)
I see no reason why not
@@Lesscoelectronics 10-4
I hope you included the brand and where we can get it
I am not sure if there is a complete kit with all of the components in it, but you can find them all on AliExpress
Magnet: www.aliexpress.com/item/4000382082121.html
Keypad: www.aliexpress.com/item/32673908668.html
Power Supply: www.aliexpress.com/item/32763536883.html
Door Exit Button: www.aliexpress.com/item/32949198370.html
Hello Sir. Can i please ask you to show or send me the Link, to buy one of this kits, to myself. Like you say Sir, I Wish i had one of this , long ago.
Please help me out.
Thank you also for sharing your work. Im very thankfull for that.
This seems to be the current model now:
www.amazon.com/Weatherproof-Control-Electric-Magnetic-110VPower-x/dp/B071X6LFFS/ref=sr_1_4?ie=UTF8&qid=1542816530&sr=8-4&keywords=ip65+electronic+magnetic+lock
Save yourself a TON of money and just buy each component individually on AliExpress. The kit on amazon is way overpriced for the same components. Currently as of Feb 15, 2020 the following items are only $78.34 USD The kit on amazon is $100 more expensive.
Magnet: www.aliexpress.com/item/4000382082121.html
Keypad: www.aliexpress.com/item/32673908668.html
Power Supply: www.aliexpress.com/item/32763536883.html
Door Exit Button: www.aliexpress.com/item/32949198370.html
So, if there's a power outage, will it still work?
I don't think so...
How it is called? And how much is it? Question if the power goes off. Does it work? If i destroy the keyboard can i unlock it?
In case of a power outage it remains open cause it needs power to electrify the magnet.
looks like a good product can you give me the name of manufacturer
where i can get the key chain remote and the remote is programmed to the keypad or to the power supply
Got that all figured out. How do you program the transmitter?
That was simple enough fo my kit, it was actually the easiest part. the instructions worked just as the instructions showed.
Maybe I have a different instructional book, mine says to open the back of the machine shell, (I'm assuming that means the transmitter? ) and then connect to the power supply...I don't see how this thing connects to the power supply..everything else is going great though. I bought it for my camper lol. A little tricky with the door. So anyway, maybe I'm interpreting it wrong.
the shell you mentioned is the unit where all my wiring is connected into.
Bro, can you just lay it out for me pls? I've had the unit apart, the transmitter apart, I don't see where I can connect anything to it...can you just write a brief step by step? I'd really appreciate it if you could do that, if you can afford the time to do so..thank you in advance
call me tomorrow 904 342 5491, My me is Martin
Muy util, compre uno similar y crei que no podria conectar y mucho menos que trabajaria, pero con la ayuda de este video lo pude hacer, gracias
huh
I want to make a lock for cycle. I want to use it like I swap a card it unlocks the cycle and then locks it. Can you suggest me stuff.
where is it parked?
wow very very good thanks for that i like that
What's the name of this device? Where to buy? Do you have a link to purchase?
try this 1 its the same but with fingerprint access www.ebay.co.uk/itm/Fingerprint-RFID-Card-Access-Control-System-280kg-Magnetic-Lock-2Remote-Controls-/142746386558?_trksid=p2349526.m4383.l4275.c10
This link worked as of 3/2019: www.ebay.com/itm/620-LBs-Kit-Electric-Door-Lock-Magnetic-Access-Control-ID-Card-Password-System/171841317313?ssPageName=STRK%3AMEBIDX%3AIT&_trksid=p2060353.m2749.l2649
www.ebay.com/itm/620-LBs-Kit-Electric-Door-Lock-Magnetic-Access-Control-ID-Card-Password-System/171841317313?ssPageName=STRK%3AMEBIDX%3AIT&_trksid=p2060353.m2749.l2649
i know this is an old video but just to let you know if some one uses a screw driver to take the screw off the bottom of the keypad they can just join the common and normally open wire together and the door will unlock for them
Maybe you watched one too many James Bond Movies...
Yeah but from the looks of it it’s stand alone and if they have wire snips they can cut it and get in
can any body tell me how to creat the user id and pin plis
How did you wire the remote control receiver?
I explained that, I grabbed power in the exit sign above the door
Where did you purchase the components from???
its in the comment section
Speaker cable for 110ac? I wouldn't be instructing people to do that
Why, the stuff I usefor car audio is actually better quality copper and far better rated than standard 3/1 any day!
@@Lesscoelectronics phew! glad to hear this, I use speaker wire for 120V all the time! I figure it's beefier than lamp wire you can get and its just copper right?! Thanks for all your videos Martin, you helped me through my first remote start install many years ago. You're kinda nuts posting your phone number here though ;)
Well I'll do it anyway. I hope that's ok with you. FYI look up what car audio wire ratings are and the latest china man wire, You may be suprused what you find. Don't get hung up on labels..
can i use cat5 ftp cabel i whole situation?
Yes you can everywhere except for the power cable
@@Lesscoelectronics for power i will use 2x0.75 cable
how to change the password of access control?
What happens when you lose power
The lock in normal situations will just not work with a loss of AC power, However a nut like me tie it into their security system's backup battery/inverter, So I never lose power.
i am sure there is a battery power pack in case there is no power
the kit is normally closed when powered so you wont get locked out with no power
it remains unlocked
Great Video !! Thank you !! My Key Pad would not work unless I used the Master Code 999999.
no problemo
This system is not International Building and Fire Code compliant. This system is super unsafe please do not use this video as a guide unless you want to incur fines for violating fire code.
Chris Balch How? yes he should have installed a emergency door release. But how, apart from that?
Oh I'm sorry it's safe because of an electricity goes off it unlocks
I don’t need your code I’ll just snip your power
code is 123456 LMAO :)
NOT genius..... Your IT guy can open that with NO problems.... LITERALLY "NO PROBLEM".....
so serious...
Just show everyone how to use the thing but don’t go through how to wire. Not very informative video for what I need