Just a bit of advice because I spent five hours cutting an old impeller off the shaft, use anti-seize on the impeller shaft threads where it screws to the impeller. Save the next guy working on the ski
Ours was makin a rough rattling sound at idle in the water. Figured some rocks got sucked up in there from beaching it so often. Took apart the housing and a bunch of little pebbles fell out…. except they were shiney. Yeahhh those were the bearings. Completely cooked. Been trying to figure out how to get that nut off and was about to buy a complete new housing till i saw this and the tool to remove the impeller
Where did u get the kit from and tools and was it a good kit I have a 2017 spark trixx and just blew threw my bearing and I don’t want to get a bad kit
Hey do you know how I can get this rope out of this propeller? I’ve cut most of it out but can’t reach the part near the propeller because the guard below it just won’t come off. The bolts don’t unscrew.
How freely is the impeller supposed to spin? I had to pull the jet pump off of my 2020 Spark because it sucked up a bunch of weeds. I can spin the prop by hand but it seems to me it should rotate a few times after I let go.
The shaft replacement on a RXTX 300 is very similar to this. Thanks for posting. Definitely a big help!
No problem!
Just a bit of advice because I spent five hours cutting an old impeller off the shaft, use anti-seize on the impeller shaft threads where it screws to the impeller. Save the next guy working on the ski
Ours was makin a rough rattling sound at idle in the water. Figured some rocks got sucked up in there from beaching it so often. Took apart the housing and a bunch of little pebbles fell out…. except they were shiney. Yeahhh those were the bearings. Completely cooked. Been trying to figure out how to get that nut off and was about to buy a complete new housing till i saw this and the tool to remove the impeller
Hell yea I’m glad you got it figured out!
Did you like my technique? 😂
@@CocosPlayound too bad i ordered the wrong size one. Too big for the hole lol
Other than the spline tool to take the impeller off, did you need any special tools? Do you need the sea doo bearing, seal pusher tool?
Nope
Where did u get the kit from and tools and was it a good kit I have a 2017 spark trixx and just blew threw my bearing and I don’t want to get a bad kit
Bay Area power sports or pwcparts
hello. you happen to have the part number on the bearing/seal kit? what site did you use
I’m pretty sure it was PWCPARTS.com
Hey Coco, did this repair fix the problem of eating into the wear ring?
Yes it did
Hey do you know how I can get this rope out of this propeller? I’ve cut most of it out but can’t reach the part near the propeller because the guard below it just won’t come off. The bolts don’t unscrew.
Pull
The pump
Intake grates have 14 mm nuts on the inside and you have to split the back half of the ski to get to them. Pull the pump
How freely is the impeller supposed to spin? I had to pull the jet pump off of my 2020 Spark because it sucked up a bunch of weeds. I can spin the prop by hand but it seems to me it should rotate a few times after I let go.
If the bearings are good and seals it should be firm. So maybe spin halfway around but it should freely spin like a wheel. It shouldn’t binding either
@@CocosPlayound Thanks for the info!
Is the shaft coming out of the motor where you pull the pump off supposed to have any play in it?
Yes the drive shaft floats between both
Awesome thanks
How often should the pump get oiled?
I would refer to the owners or service manual
Ok thank you
Do you have a video of you installing the shark teeth
Sadly I do not
I know you talked about it but…..Can you list what you ordered? Would be massively helpful, getting ready to do this to my 2017.
Full jet pump rebuild kit plus impeller shaft
👏👍👌🇳🇴