Finally!!! Thank you Drone Mesh for getting out of your comfort zone (AKA building videos) and doing setup/software videos. Like I already said, you have a way to explain things that Mr Average Joe will grasp. Thanks a lot again and keep them coming. :-)
10:58 so bud I’m sorry to be bearer of bad news but it does destroy the pads when you rip them off making it never be accepting of that plug port again
If you have a power distribution board and opto ESC's you'll have a 5v out on PDC, in which case you could wire up a red and black wire to one of the + and - of the 8 channels (not the s) pin.
Just take from the 12 v battery to 5 ⎷ converter... and rest of the wires to individual esc. So you have 12 V for motors and rest of the board 5 V. And don’t need distribution board.
i am totally new to this and electronics is my weak point. Thank you for taking it slow and helping me understand how this relates to the betaflight and what each connection do.
the easy way to tell the real SP racing F3 boards from the fakes is the real one say cleanflight on them and have the cleanflight logo. The fakes say SP racing F3 V1 right above the motor signals hope this helps people know the difference.
I know this video is almost a year old. but very helpful. I have a question on the buzzer.. what are the pads on either side of the buzzer holes? I soldered my buzzer to them instead of the holes and it doesnt work.
Can I use uart1 pads for either sbus or sport telemetry, even though it is used for the usb connection? If I use uart1 for sport, would it still connect normally to betaflight?
I am using FS ct6b transmitter and FS r6b receiver when I save as pwm it changes to ppm and I am not able to fly my drone so help please it is my one year hardwork
I subscribed to your channel in the first 47 seconds of the first video I've ever seen from you! Haha "..and watch people make it super complicated when it's really not" !!!
clarence soh teak Vbat is actually for battery monitoring, it takes the full power from the battery and measures it. You can use the settings in beta flight to set the the max and min voltages so that the buzzer sounds on low voltage. To power the FC from the pdb yes you can use the 5v source but you'd plug it into any + & - points near the motor signal points, these are located where you hook up the ESC signal wires labeled 1 through 8. The square points are for signal and the rounds are positive and negative like he spoke of early in the video here 1:08
You remind. Me of the person that hooked me to this hobby by the way he explained things! Jc! R.I.P! KEEP UP THE VIDS BRO AS ill soon hook up a patron account!👌👌👌👌👏
I've got 2 questions. 1: DoesThis flight controller got it own BEC on board, can i supply power straight from pdb without BEC (4S lipo) 2: will it fry when i power it with 6V ?
This was extremely helpful all the way to the end, where I’m still not sure, from this explanation, on how to hook a buzzer for vbat LV warning. Am I soldering a connection fron Vabt to the buzzer? Never explained. Not a complaint, as I do appreciate what is here, very helpful!
I keep trying to plug in the flight controller to my computer with the drone setup from another video, but my computer that runs windows 10, will not recognize it. Do you know what the issue is?
My board is never recognized by betaflight. Betaflight keeps closing the serial port after ten seconds, and I can never get the board connected. Please tell me if you have a fix!
Hey mate, great video. I'm a newbie to this quad building. I have wired my 4 in 1 ESC up to flight controller via 4 wires & to the signal ports 1,2,3 &4 on my flight controller. I run everything through cleanflight & everything works, transmitter, motors run etc. Have connected receiver up via PWM. The problem I have is, when I turn the transmitter on to arm, the CPU jumps to 100%, therefore cannot arm the quad. Is there something I'm missing? Any info would be much appreciated, Thanks
Does the F3-Flight-Controller support OSD of radio strength and battery, out of the box? If so, how do you wire camera and transmitter to achieve this?
@Drone Mesh This may sound like a stupid question, but Im going to build my first quad. I have a Futaba T8J with a gimbal centering kit on. Do I have to change any setting on ether the flight controller or the remoter being that the throttle automatically centers? P.S. How would I set up the quad to the arm button as the DJI CSC to arm.
Hi I want to use for airplane. I configure it but my servos don't move. If I connect to cleanfligth and go to motor tab. I can see servo signal changing wen I tilth the board. But actual servo is not moving.
Please I need help when I connect it to beta flight it simply statesNon - Cleanflight/Betaflight firmware is not supported, except for CLI mode. Can somebody please help?Desperate person here in need of help.
yes you have to solder the boot pads then plug it in to beta flight, it will be in duf mode, just flash the new firmware for your board then undo boot pads n plug back in, good luck.
Hello. I'm a noob on this things. I want to build a drone not for racing but to do simple things such as altitude hold things, maybe add a gimbal and camera, probably a vtx and ccd camera to fly far. it should have a gps also, maybe use mission planner or similar. So my question is, are these f3 or maybe the f4 FC's good for that purpose? The F3 it must be the deluxe version or acro will do? will i use betaflight or other software? thanks in advance
Just wanted to say thanku for your explanations. Great! I learnt a few things. 1) Bridging + & + etc won't (from what you said) cause problems between motors. Buzzer port, voltage feature etc! I have a FS-iA6B Flysky receiver module. Should I use the UART 3 or the white port on left to hook up the receiver. I'm assuming these are different modes of communicating with the receiver. Sbus vs PPM...is that correct? If you or others could assist me and have time to explain how best to connect the FSiA6B to this board this would be seriously appreciated. Thanks again for the time taken to explain some of the features on the board. Love to see a full rundown of ways of setting up various receivers to this FCtrl. Awesome work thanks again for the video.
Great video and easy to understand. I do have a question though, where does the input (power from the pdb) go to? Is that what the VBAT terminal is for?
I try to answer everyone when i can but its becoming more difficult. Every once in a while I try to go through all the comments and help as much as possible. :)
im making my own receiver with an Arduino and an NRF24L01 radio module, this is ppm right? so then i should leave the receiver mode on PPM RX input right?
Hey, thank you for this Video. I have just one question left. Does somebody know how I integrate telemetry data on my FPV-Googles? For example how do i connect GPS or Batteryvolltage to the FC, so it will be showen on on my googles?
I bought the F3 flight controller Deluxe 10 DOF for multirotor racing. There are trouble shooting codes coming on there are 4 long red lights then a bunch of fast one could you tell me what’s wrong please!
drone i have a rxsr going to a spracing f3 on a x220 wizard , would you hook it up through the io2 or just uart 3? i set it up for fport but rx was not working on betaflight 3.3 in the receiver tab. and of course you find conflicting reasons why and what is the reason for that to happen. so i was going to skip fport and just get flying but my rsxr is toast . second time i tried to bind after firmware update the fs button ( pad ) fell off so i ordered another.
@@DroneMesh oh thanks..... You seem experienced in drones and as you might have guessed already, I am a newbie.... I'll contact you if I need any help!
Same flight controller using, receiver not communicating with flight. Using Turnigy 9x Transmitter and receiver is Frsky V8fr. Unable to communicate with flight controller.pls help..
how do you power it ive been trying for awile to get it to work but it wont power up when i plug the usb in it powers up but it wont any other time im building a martian II with the pdb it comes with can anyone please help me
Hi! Could you help me? I have the SP Racing F3 flight controller, deluxe (from Bangood) and I have flashed the CLFL v2.4.0 SPRacingF3 version with cleanflight configurator 2.4.0. In the main page the icon of "baro" is green and at menu sensors I can verify that the barometric sensor works well. On Taranis I have three switches, 1 "arm", 2 "angle"-"horizon"- "air mode", 3 "baro"-"headfree" (min1000, mid1500, max2000). All these functions are working fine when I am selecting them from modes menu and their icons become green, except the "baro". Unfortunately, the "baro" cannot be activated. Do I have to make any adjustment to CLI? What do you think about this issue? From CLI: set baro_bustype = I2C set baro_spi_device = 0 set baro_i2c_device = 1 set baro_i2c_address = 0 set baro_hardware = AUTO set baro_tab_size = 21 set baro_noise_lpf = 600 set baro_cf_vel = 985 set baro_cf_alt = 965 set mid_rc = 1500 set min_check = 1050 set max_check = 1900 ………………………………………….. Frame: 240 mm ESC: Holybro Tekko32 35A BLHeli_32 Dshot1200 Motor: Emax RS2205S 2300KV Thank you in advance!
Cool I'll be looking for it and thanks for doing these. I know I'm jumping ahead again but I installed a discovery "buzzer" to the buzzer contacts. Configured it in Betaflight and It comes on with the assigned switch, BUT! It also comes on with the arm switch when I arm the motors. Nothing overlapping it my mode settings yet the buzzer activates with both switches. Some videos say those buzzer contacts r for low battery alarm. Don't know how many or how far u intend to take this series, but If u have time, it would be great if you could clear this up. Thanks.
Open CLI tab and copy paste these 2 commands ############## beeper -ARMED save ############## Then test again I think that will fix your problem if your battery is charged
Hi Drone Mesh, Sorry if I'm overlooking the obvious but after putting in the command I don't see a "save" button. Am I understanding your instructions?
I use the I/O1 or the I/O2 Ports on the side's for connection to the radio RX/TX as per instructions in the manual. You have to be careful when using the the two UART headers with the radio TX/RX modes. The manual can be found here... www.seriouslypro.com/files/SPRacingF3-Manual-latest.pdf
Follow up, I enter "beeper -ARMED" but don't know how to same the command , and have enter "beeper -ARMED save" . Are you meaning for me to save after entering beeper -ARMED??? sorry for the confusion on my part
Thanks for the help but sorry to report that it continues to beep when armed. It also beeps when I turn off the TX and when I flip the selected switch just as it should. But the damn thing still powers on when armed. I know you have a lot on your plate so if u wanna move on I'd totally understand. You've done way more than others. Maybe it's one of the weird things with electronics. Regardless I appreciate your help and patients with the neeb .
On the bright side I wired up a set of leds for the fist time, configured them in Betaflight and everything works great. Thanks for the doin this video.
Your receiver is Sbus compatible its alot easier than me telling you how to connect PWM. The bottom 3 pins on your receiver have s.bus Left > Signal -> goes to UART3 RX like in the video Middle > VCC -> goes to the positive on UART3 Right > ground -> goes to - on UART3
Benjamin Law Suwarat No nothing goes to TX.. just make sure you follow the steps in betaflight like in the video and make sure to enable sbus in your transmitter. That should be it. Keep me updated..
![Felix "Unfair" | [Stray Kids : SKZ-PLAYER]](http://i.ytimg.com/vi/Oswujxm2Ag0/mqdefault.jpg)
Finally!!! Thank you Drone Mesh for getting out of your comfort zone (AKA building videos) and doing setup/software videos. Like I already said, you have a way to explain things that Mr Average Joe will grasp. Thanks a lot again and keep them coming. :-)
10:58 so bud I’m sorry to be bearer of bad news but it does destroy the pads when you rip them off making it never be accepting of that plug port again
Watched a lot of videos on this subject so I can build a race drone and this has given me the greatest overall understanding of them all
Downliad AskFPV if you need help in the future :)
the best vid explaining fc controls on here,all others are so crapy.thanx so much for this video,helped me a lot more than you can imagine.
Thank you. Best video finally after 4 days of struggling and research.
Thank you very mutch!!! I finally solved my problem, with my receiver!! :D
Glad I was able to help ^_^
the best spf3 tutorial for dummies. you made my transition from buggies to drones much easier. thanks
11 min - but how do you power the board...
From one of the red wire's from one of the motor ESC's.
If you have a power distribution board and opto ESC's you'll have a 5v out on PDC, in which case you could wire up a red and black wire to one of the + and - of the 8 channels (not the s) pin.
Just take from the 12 v battery to 5 ⎷ converter... and rest of the wires to individual esc. So you have 12 V for motors and rest of the board 5 V. And don’t need distribution board.
@@AndyDeiu hey thats good, but can I use a 4in1 esc with this?
Planning on buying this for my first build.. please eli5 how to power the Fc
i am totally new to this and electronics is my weak point. Thank you for taking it slow and helping me understand how this relates to the betaflight and what each connection do.
the easy way to tell the real SP racing F3 boards from the fakes is the real one say cleanflight on them and have the cleanflight logo. The fakes say SP racing F3 V1 right above the motor signals hope this helps people know the difference.
Thank you very much but why u don't add barometer and magnetonometer by soldering them on board as I did
I know this video is almost a year old. but very helpful. I have a question on the buzzer.. what are the pads on either side of the buzzer holes? I soldered my buzzer to them instead of the holes and it doesnt work.
I have a problem with this f3 FC. Is doesn't arm. Is said runaway takeoff. Do you know what's wrong ?
Can't say thank you enough, it seems very basic but before I found this video I still had a lot of questions about the FC inputs/outputs ect. THANKS!
Can I use uart1 pads for either sbus or sport telemetry, even though it is used for the usb connection? If I use uart1 for sport, would it still connect normally to betaflight?
Thank you so much for making this setup so easy to understand and especially for pointing out the FC board orientation. 👍👍
I am using FS ct6b transmitter and FS r6b receiver when I save as pwm it changes to ppm and I am not able to fly my drone so help please it is my one year hardwork
Cant save cc3d configuration...what to do
Do you know what signalings the red LED? I have some problems with my drone :/
Thnaks for the simplified version of setup. Appdreciate it.
Great video! Thanks for taking the time to explain how everything works, cleared things up for me. Keep them coming. 👍
I know eventually you've got to tune your pic but yiy can hook this fc up without programing can't you?
I subscribed to your channel in the first 47 seconds of the first video I've ever seen from you! Haha "..and watch people make it super complicated when it's really not" !!!
Thanks very much made me understand.
Is there a video showing how to hookup the receiver?
Can i supply power using 5 volts from a pdb instead of using the vbat pins?
clarence soh teak Vbat is actually for battery monitoring, it takes the full power from the battery and measures it. You can use the settings in beta flight to set the the max and min voltages so that the buzzer sounds on low voltage. To power the FC from the pdb yes you can use the 5v source but you'd plug it into any + & - points near the motor signal points, these are located where you hook up the ESC signal wires labeled 1 through 8. The square points are for signal and the rounds are positive and negative like he spoke of early in the video here 1:08
What are the plugs on the side for??
(4:33) wait wait wait! How did you get it to talk to betaflight?
Where would you hook up your VTX and camera?
Is there a Vin and Vout for OSD? The bangood description says it does have it, but I do not see it on board, can you show me which pins would that be?
This one does not have OSD.
@@DroneMesh Thank you, one more question, how should I measure voltage or know when to change batteries with this FC?
@@yoyomario Well you can add a buzzer and connect small wire to vbat from the + of battery but make sure not to connect it to the 5V
Thanks man! That simple point on toggling on Serial RX but not switching on the UART saved me!
Thanks man for this kind video, this pretty much puts the puzzle together!
Where would the pdb connect from and to? Im having a lil problem with that...
+Sean Stewart take 5v from the pdb and connect it to the bottom ground and 5v rails
can i put mising ic magnet compas on this boad? is work or not?
One of the most informative videos on youtube, glad I dropped by. :-)
Sir..pls suggest me how to configure altitude hold function on this board and what would be supported hardware...
You remind. Me of the person that hooked me to this hobby by the way he explained things! Jc! R.I.P! KEEP UP THE VIDS BRO AS ill soon hook up a patron account!👌👌👌👌👏
Nice video! I am trying to solder a serial spectrum satellite to this board.. is there 3.3v on this?
I've got 2 questions.
1: DoesThis flight controller got it own BEC on board, can i supply power straight from pdb without BEC (4S lipo)
2: will it fry when i power it with 6V ?
Great video.
Do you have any idea where to connect the Video In and Video Out wires, to be able to use the built-in OSD?
Thanks
Poker2145 there is no OSD on this board.
Thank you so much!! Super helpful subbed
This makes sense! !! Thank You I've been beating my head on the wall!
This was extremely helpful all the way to the end, where I’m still not sure, from this explanation, on how to hook a buzzer for vbat LV warning. Am I soldering a connection fron Vabt to the buzzer? Never explained. Not a complaint, as I do appreciate what is here, very helpful!
Does this board support DShot 600?
I need help for setting up spracing3 for bicopter
From wich port do i power up this board? And does it have a power output ?
I keep trying to plug in the flight controller to my computer with the drone setup from another video, but my computer that runs windows 10, will not recognize it. Do you know what the issue is?
Wow thanks! I just subbed! This video was a great help getting my board setup properly.
Is this the Arco or Deluxe spf3?....Which one does GPS?...
how to add OSD on this FC ??? from where and how can i configure it
My board is never recognized by betaflight. Betaflight keeps closing the serial port after ten seconds, and I can never get the board connected. Please tell me if you have a fix!
Thanks, you really helped me understand the SP F3
Hey mate, great video. I'm a newbie to this quad building. I have wired my 4 in 1 ESC up to flight controller via 4 wires & to the signal ports 1,2,3 &4 on my flight controller. I run everything through cleanflight & everything works, transmitter, motors run etc. Have connected receiver up via PWM. The problem I have is, when I turn the transmitter on to arm, the CPU jumps to 100%, therefore cannot arm the quad. Is there something I'm missing? Any info would be much appreciated, Thanks
Does the F3-Flight-Controller support OSD of radio strength and battery, out of the box? If so, how do you wire camera and transmitter to achieve this?
Can you pls make a video to how to setup sfp3 acro with xsr and setup in software
@Drone Mesh This may sound like a stupid question, but Im going to build my first quad. I have a Futaba T8J with a gimbal centering kit on. Do I have to change any setting on ether the flight controller or the remoter being that the throttle automatically centers?
P.S. How would I set up the quad to the arm button as the DJI CSC to arm.
Hi
I want to use for airplane.
I configure it but my servos don't move. If I connect to cleanfligth and go to motor tab. I can see servo signal changing wen I tilth the board. But actual servo is not moving.
Please I need help when I connect it to beta flight it simply statesNon - Cleanflight/Betaflight firmware is not supported, except for CLI mode. Can somebody please help?Desperate person here in need of help.
same problem here...
You have to upgrade the firmware of your flight controller.
yes you have to solder the boot pads then plug it in to beta flight, it will be in duf mode, just flash the new firmware for your board then undo boot pads n plug back in, good luck.
boot
Hello.
I'm a noob on this things. I want to build a drone not for racing but to do simple things such as altitude hold things, maybe add a gimbal and camera, probably a vtx and ccd camera to fly far. it should have a gps also, maybe use mission planner or similar. So my question is, are these f3 or maybe the f4 FC's good for that purpose? The F3 it must be the deluxe version or acro will do? will i use betaflight or other software? thanks in advance
I followed your instructions and everything works but I do not have any OSD in my goggles. What did I miss?
This doesnt have OSD
Hi, so GPS module only in UART 2? Thanks
Just wanted to say thanku for your explanations. Great! I learnt a few things. 1) Bridging + & + etc won't (from what you said) cause problems between motors. Buzzer port, voltage feature etc! I have a FS-iA6B Flysky receiver module. Should I use the UART 3 or the white port on left to hook up the receiver. I'm assuming these are different modes of communicating with the receiver. Sbus vs PPM...is that correct? If you or others could assist me and have time to explain how best to connect the FSiA6B to this board this would be seriously appreciated. Thanks again for the time taken to explain some of the features on the board. Love to see a full rundown of ways of setting up various receivers to this FCtrl. Awesome work thanks again for the video.
Hey man do you know of any good proven 20x20 boards like this one that’s ready for GPS ?
Have you prepared a video to show how to connect telemetry to the spf3 board? That's my biggest issue.
Please do a tutorial on PPM connections or show me in anyway
How do you setup your vtx and cam with a board like this? I see no vtx or solder point on board. Shouldn't there be a video in and out.
so you do not need a PDB with this flight controller, right?
You do need a PDB. It's just a flight controller.
Great video and easy to understand. I do have a question though, where does the input (power from the pdb) go to? Is that what the VBAT terminal is for?
Dear Dronemesh, i know this is kinda old school, but could you help me with this spf3 board?i was wondering of it support dshot esc?
dose it matter what fc i use if i want to get my drone to hold it position?
You just saved me hours of frustration. A+++ 🏆🙏
can you connect a 4in1 to this FC?
Brilliant video mate do you directly solder to the pads or use the pins I am finding the pins a night mare to solder
Ryan Maynard Direct solder.
Drone Mesh thanks for getting back so soon some people on other channels are way to important to help there views out top marks
I try to answer everyone when i can but its becoming more difficult. Every once in a while I try to go through all the comments and help as much as possible. :)
im making my own receiver with an Arduino and an NRF24L01 radio module, this is ppm right? so then i should leave the receiver mode on PPM RX input right?
can I set this up with a 4in1 esc?
Are there any chances that you can make a video how to make smart audio vtx works with this fc ?
Hey, thank you for this Video.
I have just one question left.
Does somebody know how I integrate telemetry data on my FPV-Googles? For example how do i connect GPS or Batteryvolltage to the FC, so it will be showen on on my googles?
I wish there had been wires in the video. WHERE DO I ACTUALLY PUT THE WIRES TO MAKE IT WORK?
I bought the F3 flight controller Deluxe 10 DOF for multirotor racing. There are trouble shooting codes coming on there are 4 long red lights then a bunch of fast one could you tell me what’s wrong please!
what do you do to get the older beta flight to work? 3.1. I have both versions but I cannot get older versions to connect. thanks
drone i have a rxsr going to a spracing f3 on a x220 wizard , would you hook it up through the io2 or just uart 3? i set it up for fport but rx was not working on betaflight 3.3 in the receiver tab. and of course you find conflicting reasons why and what is the reason for that to happen. so i was going to skip fport and just get flying but my rsxr is toast . second time i tried to bind after firmware update the fs button ( pad ) fell off so i ordered another.
The board needs to connected with the computer during the software setup right?...... Someone please reply!!
Yes they all need PC setup
@@DroneMesh oh thanks..... You seem experienced in drones and as you might have guessed already, I am a newbie.... I'll contact you if I need any help!
Same flight controller using, receiver not communicating with flight.
Using Turnigy 9x Transmitter and receiver is Frsky V8fr.
Unable to communicate with flight controller.pls help..
Abhijeet Paul What protocol are you using??
ppm or ibus
Drone Mesh ..sir I'm using ppm.
Abhijeet Paul are you able to communicate with the FC? I have the same problem, I have a Turnigy 9xR pro and a 4Dr-ll receiver. Appreciate your help.
Can i connect the telemetry to the TX of uart3?
Ola amigo estou querendo saber se tem como realizar retorn to home com essa controladora? se ela tem barômetro e como ativar a função!
how do you power it ive been trying for awile to get it to work but it wont power up when i plug the usb in it powers up but it wont any other time im building a martian II with the pdb it comes with can anyone please help me
Hey there, I know it’s 3 year old video but do you think I can attach a vtx on spf3 flight controller ?
Only a 5v vtx and just get power from the spf3
Will the stats be displayed on the goggles ?
How does beta flight pop up so you need software
THANK YOU SO MUCH! THIS WAS SO HELPFUL
check my latest flight controller video to get more info
Thanks mate been looking for a video to connect my sbus to this fc. I had an idea but wanted to confirm. Seems to be the same as my old f1 board!
This really helped me a lot. thanks drone mesh..
Hi!
Could you help me?
I have the SP Racing F3 flight controller, deluxe (from Bangood) and I have flashed the CLFL v2.4.0 SPRacingF3 version with cleanflight configurator 2.4.0. In the main page the icon of "baro" is green and at menu sensors I can verify that the barometric sensor works well. On Taranis I have three switches, 1 "arm", 2 "angle"-"horizon"- "air mode", 3 "baro"-"headfree" (min1000, mid1500, max2000). All these functions are working fine when I am selecting them from modes menu and their icons become green, except the "baro". Unfortunately, the "baro" cannot be activated. Do I have to make any adjustment to CLI? What do you think about this issue?
From CLI:
set baro_bustype = I2C
set baro_spi_device = 0
set baro_i2c_device = 1
set baro_i2c_address = 0
set baro_hardware = AUTO
set baro_tab_size = 21
set baro_noise_lpf = 600
set baro_cf_vel = 985
set baro_cf_alt = 965
set mid_rc = 1500
set min_check = 1050
set max_check = 1900
…………………………………………..
Frame: 240 mm
ESC: Holybro Tekko32 35A BLHeli_32 Dshot1200
Motor: Emax RS2205S 2300KV
Thank you in advance!
Cool I'll be looking for it and thanks for doing these.
I know I'm jumping ahead again but I installed a discovery "buzzer" to the buzzer contacts. Configured it in Betaflight and It comes on with the assigned switch, BUT! It also comes on with the arm switch when I arm the motors. Nothing overlapping it my mode settings yet the buzzer activates with both switches. Some videos say those buzzer contacts r for low battery alarm. Don't know how many or how far u intend to take this series, but If u have time, it would be great if you could clear this up. Thanks.
Open CLI tab and copy paste these 2 commands
##############
beeper -ARMED
save
##############
Then test again I think that will fix your problem if your battery is charged
Hi Drone Mesh, Sorry if I'm overlooking the obvious but after putting in the command I don't see a "save" button. Am I understanding your instructions?
Thank you for the video! Very good info man, thank you!
Brilliant video thanks what's the io ports you didn't mention them
Can i make a hexa with it please reply
I use the I/O1 or the I/O2 Ports on the side's for connection to the radio RX/TX as per instructions in the manual. You have to be careful when using the the two UART headers with the radio TX/RX modes. The manual can be found here... www.seriouslypro.com/files/SPRacingF3-Manual-latest.pdf
Helped a lot keep up the good work :)
Does it connects gps
Follow up, I enter "beeper -ARMED" but don't know how to same the command , and have enter "beeper -ARMED save" . Are you meaning for me to save after entering beeper -ARMED??? sorry for the confusion on my part
Larry Faucett
first command
beeper -ARMED
press enter
second command
save
press enter
then your done
Thanks for the help but sorry to report that it continues to beep when armed. It also beeps when I turn off the TX and when I flip the selected switch just as it should. But the damn thing still powers on when armed. I know you have a lot on your plate so if u wanna move on I'd totally understand. You've done way more than others. Maybe it's one of the weird things with electronics. Regardless I appreciate your help and patients with the neeb .
On the bright side I wired up a set of leds for the fist time, configured them in Betaflight and everything works great. Thanks for the doin this video.
Larry Faucett I'll try to have a video out for you today to debug this issue.. If I will not be able too I will send you more commands to run.
sorry for the dumb question but how would I connect my SPF3 to a RadioLink R9DS?
Benjamin Law Suwarat Is your receiver PWM or ppm??
Drone Mesh pwm
Your receiver is Sbus compatible its alot easier than me telling you how to connect PWM.
The bottom 3 pins on your receiver have s.bus
Left > Signal -> goes to UART3 RX like in the video
Middle > VCC -> goes to the positive on UART3
Right > ground -> goes to - on UART3
Drone Mesh I see, so nothing goes in to TX?
Benjamin Law Suwarat No nothing goes to TX.. just make sure you follow the steps in betaflight like in the video and make sure to enable sbus in your transmitter.
That should be it. Keep me updated..