Thanks for the walk through. I thought I had a burnt out bulb but as it turns out, my bulb was good, I just needed to unplug it and then plug it in again.
You don't have to remove the fender liner or go through the top of the engine bay. The foglights pop out from the front of the bumper. You just pop the little silver trim ring that goes around them off with a flathead as it's just held in with a few pressure clips and then there is one T25 screw that holds the lamp in after you remove that the lamp just comes right out. Replace the bulb, pop it in and screw it in then just replace trim piece and you're done. Takes less than 5 minutes to do both and you don't have to wait for the engine to cool down or scrape your hands up.
Appreciate the video question for you since you seem to know more than anyone I’ve found on here. 1 how are your head light flickering like that. Two I’m trying to install a led hood light strip I’ve done it on my Nissan but this is way harder one not sure which spot to tap into in the fuse box and two I can’t figure out where to find the turn signal wires?!! Nissan it was right there this is all LED lighting and I can do some stuff but you seem like a mechanic any advice would be extremely helpful!
The lights aren't actually flickering. That's simply how the camera picks up the led lights. In terms of a tap, depends on what you want that to come on with. Guessing drl's? And the wiring, I'm not sure, I've never removed one of the headlight assemblies on this to get to the wiring.
I thought it was the camera but I wasn’t sure….yea I want to add a hood light strip which I can do but the turn signal part I love and want to wire but I can’t figure out where that wire would be cause this headlight doesn’t seem to have a normal light bulb for the turn signal
IKR. I got my arm stuck and scraped it all up trying to pull it out. Ended up pulling the trim and removing one screw to pull the whole fog light assembly out the front. Was waaayyy easier for me than trying to get my arm down there. All you need is a small screw driver and a T25 torx
![Megan Thee Stallion - Bigger In Texas [Official Video]](http://i.ytimg.com/vi/QxTkZTLWdo4/mqdefault.jpg)
Thanks for the walk through. I thought I had a burnt out bulb but as it turns out, my bulb was good, I just needed to unplug it and then plug it in again.
Happy to hear this was helpful
Hey Thank you for the demo. I was going to purchase white halogen but will head your viewpoint on Fog effectiveness.
You're welcome
The only helpful thing coming from New Jersey lol. Thank you
Exceptional tutorial. Thank you your views were very clear
Very thorough and helpful !
You don't have to remove the fender liner or go through the top of the engine bay. The foglights pop out from the front of the bumper. You just pop the little silver trim ring that goes around them off with a flathead as it's just held in with a few pressure clips and then there is one T25 screw that holds the lamp in after you remove that the lamp just comes right out. Replace the bulb, pop it in and screw it in then just replace trim piece and you're done. Takes less than 5 minutes to do both and you don't have to wait for the engine to cool down or scrape your hands up.
Do you know if I can change the yellow fog light into white to match my headlights?
Yes absolutely. From the factory they were white, at least in the US. I replaced a factory white bulb with yellow here.
Thank you so much for this video!!!
Really thanks for the video man. I wish you would've shown them at night
Any time
Thanks so much buddy
Happy to help
Thanks for the overview!!!!
You bet!
Appreciate the video question for you since you seem to know more than anyone I’ve found on here. 1 how are your head light flickering like that. Two I’m trying to install a led hood light strip I’ve done it on my Nissan but this is way harder one not sure which spot to tap into in the fuse box and two I can’t figure out where to find the turn signal wires?!! Nissan it was right there this is all LED lighting and I can do some stuff but you seem like a mechanic any advice would be extremely helpful!
The lights aren't actually flickering. That's simply how the camera picks up the led lights. In terms of a tap, depends on what you want that to come on with. Guessing drl's? And the wiring, I'm not sure, I've never removed one of the headlight assemblies on this to get to the wiring.
I thought it was the camera but I wasn’t sure….yea I want to add a hood light strip which I can do but the turn signal part I love and want to wire but I can’t figure out where that wire would be cause this headlight doesn’t seem to have a normal light bulb for the turn signal
Thanks for the video. Would you by chance know what the light bulb model/number it is?
Yes, h8 are the correct bulbs
Thanks!
Thanks for the video!
You bet!
Hello, how you doing I was wondering where you get your led headlights?
Headlights are factory in this.
idk how your arm fit into the driver side. i was able to access the bulb but with zero room to spare to twist, pull the bulb out etc
I'm used to contorting my body to work on cars
IKR. I got my arm stuck and scraped it all up trying to pull it out. Ended up pulling the trim and removing one screw to pull the whole fog light assembly out the front. Was waaayyy easier for me than trying to get my arm down there. All you need is a small screw driver and a T25 torx