How to install the Frost King Shrink Window Insulation Kit
HTML-код
- Опубликовано: 2 окт 2018
- How to install the Frost King Shrink Window Insulation Kit.
The Frost King Shrink Window Insulation Kit is the easy to install, easy to use solution to winter drafts. Goes up in just a few minutes, and lasts the entire winter.
more info - www.frostking.com/products/wi...
Help and Tips - www.frostking.com/support/win... 
Хобби
Pro Tip: Apply the tape, but only expose the other side of the tape on the stripe at the top of the window. Apply the top first. Then slowly peel one side as you apply it. Then do it to the other side. Last the bottom. Goes on WAY better without it sticking to a stripe before you're ready.
Makes sense. Thanks!
they should include your tip in their instructions and pay you for this info. The film wants to stick to everything & I could not get it even and tight till I followed your instructions. It's made in the USA, I'm surprised. I thought it was another product from overseas with a copywriter who was not English speaking
After affixing the plastic along the top, cut in the middle of the 'down tape', pulling it up half way and pressing in the plastic as you go, then the other side in similar fashion...Back to the bottom half on both sides until you are at the bottom window sill. Slice in the middle of the bottom tape and start in one corner pulling taughtly to the other corner for a tight fit. **Let sit for 30 Mins so that the tape will become accustomed to adhering to the wall.. Then use the heat gun....
This works 100% and it's super easy to install, I don't have a hair dryer, so I used my space heater.
This worked great for me! I had to cover the window because the cold air was wilting my plants! Not any more!
Lol, that flick at the end
😂😂😂
I'm sealing up my son's air conditioner because we don't use it and all this air gets out. It's rediculous. Thanks for your video. You made it look so easy.
Thank you
I bought this for my apt window that keeps frosting up. It's frosted now. Will installing it now still help?
Thank you this is v helpful and v well done
I really wish I knew this was how they're applied before I bought them. I have cats. thought it was going to be more like a screen protector
The roll with the built in cutter is way better, easier and faster.
Do you need to blow it dry
💥splat
Does this install over or under blinds?
You should keep it under since it's shown as close to the window as possible
Is this good for summer also or do I need to take them down
This will keep the cool air in and hot air out, cuts down on AC and Heating bills in both seasons!
"blow dry starting at the top" but just around the edges, or across the whole window? Neither video shows or tells.
All over…don’t get too close or you’ll burn a hole thru it 😮
you blow dry the whole window film. you'll see the film change and become taut as you do and any small ripples in the surface will smooth out. when you're done if you tap it the whole thing feels like if you tapped on the surface of a filled balloon and it's completely see-through.
It says "...from the top down..." at 00:48 seconds. That would be... The entire window! 😂😂😂
Does this help with doors too? I have a patio door through which air leaks during winters
Yes, they make a door size one for this. As long as you don’t need access to the door, I think it should work.
Redo this video without skipping steps like the bottom...
Will the tape come off the window in the spring?
It will but it might take up some paint from the trim with it. Had repaint a few of mine last Spring.
Maybe...Maybe not easily...
I would use the hair dryer on the tape before taking the tape off. It might make it easier to remove.
Use a razor blade type gasket scraper. Gently. And I’d recommend lightly wiping the window sill down mineral spirits, and wiping it dry, before using the tape. This way it cleans the surface and is less likely to rip the paint up with it when you pull it off.
I put up the tape, but can't get the backing off it. Any tips?
do you really need double sided tape can you just use regular clear packaging tape
I thought they left the window sill so dirty to show a step to clean it first lol. Nope
😂
This video ignores the most frustrating and time consuming part of the process.
I love using the Frost King insulation kits, BUT . . . I spend more time trying to separate and getting a starter piece to the backer tape than everything else. Once you put up the tape (sans a backer starter) how do you get a piece of the backer to remove?
My experience is that you need to have a starter on the backer or else the tape comes right off the wall. Wasted tape and frustration. So, in order to do this, I cant wait 15 minutes for the tape, to adhere to the wall. I have to remove the backer, then cut the tape to get a starter piece. If I mess up, I spend (without exaggeration) an extremely long time trying to creat a new starter piece.
What am I doing wrong? It should be as easy as displayed, but after more than a decade of using these kits, I've not found a better solution. Someone, please tell me how to do this. It might cut my installation time by 1/3 or more.
Check out the comments under the other (longer) video for this product. People are having a lot of issues with the tape. I'm about to try it for the first time... wish me luck! If all else fails, I'll just use some other kind of tape, even if it's not double sided.
After affixing the plastic along the top, cut in the middle of the 'down tape', pulling it up half way and pressing in the plastic as you go, then the other side in similar fashion...Back to the bottom half on both sides until you are at the bottom window sill. Slice in the middle of the bottom tape and start in one corner pulling taughtly to the other corner for a tight fit. **Let sit for 30 Mins so that the tape will become accustomed to adhering to the wall.. Then use the heat gun....
The tape is trash
Don't buy Frost King. It's cloudy and the creases don't come out after using blow dryer! The tape isn't very sticky, either.