@@imronmuhammad4678 tanya mas wahyu, pdhl sy juga berharap karya2 mas wahyu di pasarin di olshop apalagi power2 Class-D rakitan yang bisa di aplikasiin ke mobil, pasti sy minat banget daripada beli power2 branded yang harganya mahal dan gak terjangkau.
Sudah saatnya orang kreatif seperti mas ini diajak kerjasama perusahaan buat merek sendiri dibidang elektro agar punya merek sendiri dalam negri dan bisa diexpor klr negeri juga, tentu dengan kwaltias terbaik
idle current at 4.8A a very high idle consumption will drain the battery faster.. with low frequency transformer type at same power, idle current can be less than 2A. So far the demonstration was highly satisfactory. Nice work!
Kalau pas cetak pcb lagi, saya pesan pcb nya mas untuk plts dirumah. Selama ini beli inverter yg udah jadi, kalau rusak bingung servisnya ngeliat jalur😄
Whay use 2 inverter stages? Wouldnt it be much easier if Simply boost the 12v to 300or 400v and then Use EGS Hbridge to make it a Sin wave? Anyway awesome build
Hello! Good work! But why a litz wire consists from such thick wires? When I made AC/AC HF converter from galogen lamps (300W) I had unsucces with thick wire 0.33millimeters. A transformer was too hot and a current density was roughly 2 A/mm2. When I change my homemade litz 0.33mm on 0.16mm the temperature of wire had been decreased much. It was a construction like a steel rope. 12 wires was a minimal twisted wire unit. These wires (5 unit) twisted into one - e.t.c. A current density was 4A/mm2.There wasn`t any cooler.
Hey, how do you choose the RC combination you used for the SG3525 from compensation pin (pin 9) and inverting input (pin 1). As there is not much information about how to calculate it on the internet so pls if you could help me out 🙏
hello friend thanks for sharing your project. I have a question. I am setting up this project in my country, the ac voltage is 120v. then the DC volage is how much 220 dc so that the output can modify it to 120v ac.
Hi, congratulations!! Could you tell me if have you experienced any issue or problem with the LP filter?. Did you have any problems with L-C resonance? I have been working on a prototype using EGS002 (also using a compatible pinout board based on a PIC that I have been working on) and in both cases I had some problems with LCL filter. It seems that at resonance frecuency, there is a lot of energy and I can see high current peak across the capacitor in paralel branch, wich still remains if a limiting series resistor is added. I think it could be a matter of choosing the resonance frecuency which should not to be close to a (sub) multiple of switching frecuency (in EGS002 switching frec is around 22-23 KHz, in my board it is 25 KHz), but unfortunatelly I am not sure about it. I will aprreciate any comments about this subject. Thank you very much.
Great video Sir .... Thanks for sharing .... I need to small help .... The EGS002 Have any settings for HIGH FREQ (380VDC to 220VAC) .... The EGS002 Used Low frequency inverter also 12VDC to 220VAC ..... How to H Bridge Switching will work Please ....
Never use totem pole driver for high volt boostrap ground connection it will break down very fast use optocoupler isolation and use half bridge driver ic or just the optocoupler
Hello again.there is a resistor named (sens) in this board what is that for and what the range of it ...in fact what is range for (sens) resistor in board for 24v...tanx.i dont know why i don’t have 3525 pwm pulse on my mosfet pins
@@WahyuEkoRomadhon hahaha 😁,, Klo SMPS FB+PFC saya masih agak bingung karena saking banyaknya komponen yang gak boleh asal-asalan 😁 Saya tunggu video2 selanjutnya mas,, suka pas pengujiannya👍😁😁
@Wahyu Eko Romadhon hello friend thanks for sharing your project. I have a question. I am setting up this project in my country, the ac voltage is 120v. then the DC volage is how much 220 dc so that the output can modify it to 120v ac.
@@WahyuEkoRomadhon I am putting together the same of your inverter project from 24v DC to 120v ac. I have to make the modifications to the voltages. My question for the step-up voltage of how much is it from 24 to 220v DC and 220 DC to 120v ac. my question if it is ok in the first stage. Thank you
Hai, Mengapa inti ferit menghabiskan begitu banyak arus DC? dengan beban dan juga tanpa beban? /// hi, Why is the ferrite core spending so much DC current? with load and also without load? /// ওহে, ফেরাইট কোর কেন এত ডিসি কারেন্ট খরচ করছে? লোড সহ এবং লোড ছাড়াও? /// Thank's!!!!
Hello again.I try to made this nice project I’m on made ring fritte ...i used 2*4 turn for primary and 65turn for secondary and then i don’t know for two other out put how to turn ...i use 3turn and 3 turn again but when i connect it to board i have dc 380volt well but my 8 *fr207 start to hot so much and my step down module start hot much ...!!!
wih mantap tenan, mas eko,, dan akan lebih jos lagi kalau ada penjelasan nama komponen komponennya dan penjelasan laiinya,, jujur mas suara musik nya agak sedikit mengganggu, mungkin akan lebih keren dan sangat bermanfaat jika suara musik itu di ganti dengan suara penjelasan jenengan dari semua aktifitas yg di buat,, ,, oh iya ada no contak atau wa kah,,sy mau konsultasi atau pesan barang barang yg sudah mas rakit..
Sir, can i use this with both 12V and 24V DC input, Does this circuit haa short circuit, under voltage , over voltage protection, I need more details about this
Hello again.i made this project completely. Now i have two problem...one-> my hi volt fet(23n50) near inductor start warming to hot with out any things connected for run or light(i use about 3mh inductor) Two->when i connect a fan or light to out put 220vac start to down and then turn off and inverter module restarted.why? All things start true and good and out put is sine wave good but i don’t know why that two problems happen!,,! I use 24vdc20a power to run. Can you help me to solve?tanx
ini baru suhu karya2 nya bener2 rapih seperti produksi pabrik, sukses mas eko, 👍👍👍👍👍
Thnks mas
TK tukune lek
@@imronmuhammad4678 tanya mas wahyu, pdhl sy juga berharap karya2 mas wahyu di pasarin di olshop apalagi power2 Class-D rakitan yang bisa di aplikasiin ke mobil, pasti sy minat banget daripada beli power2 branded yang harganya mahal dan gak terjangkau.
Buat produk2 yg bermanfaat untuk kemajuan negara kita mas, kembangkan terus mas
Sudah saatnya orang kreatif seperti mas ini diajak kerjasama perusahaan buat merek sendiri dibidang elektro agar punya merek sendiri dalam negri dan bisa diexpor klr negeri juga, tentu dengan kwaltias terbaik
Amiin mas
@@WahyuEkoRomadhon aminnn moga cepat terjadi
DARI SEGI ILMU PENGETAHUAN DAN DI PADU SEGI EDITING NYA MANTAP BUAT DI TONTON. MAJU TERUS PAK EKO
Thnks mas
Bang wahyu ga perlu diragukan lagi, mantap uey
Thanks bli
Bsa di beli bos
Super Hyper Rapi Dan Tampilannya Keren Banget projectnya Suhu 😁.. Ampunn 🙏😂...
Mmpung ad mas
idle current at 4.8A a very high idle consumption will drain the battery faster.. with low frequency transformer type at same power, idle current can be less than 2A. So far the demonstration was highly satisfactory. Nice work!
Just 0.6A idle
@@WahyuEkoRomadhon in the video we all saw 4.8A idling
@@WahyuEkoRomadhon retty easy to see how bad your inverter works!
Check his subtitles. He mentioned that a 60w soldering iron and 55w lamp are also connected , that's what drawing the current when the hot gun is off.
Produksi yg banyak dan harga bersaing mas, biar indonesia semakin maju dan bangga dengan buatan anak negeri
Amiiinn mas. Insyallah
Cetak Pcb pakai Anti Nyamuk Sofell Nyimak aja lah😄😆.
Very nice. Is any schematics and PCB along with software available for use, thanks.
joss kotos-kotos barang atos ojo nganti bledos...auto subrek mbah
Tambah grid tie function trus limiter sama datalogging.
Pasti lebih joss.
Kalau pas cetak pcb lagi, saya pesan pcb nya mas untuk plts dirumah. Selama ini beli inverter yg udah jadi, kalau rusak bingung servisnya ngeliat jalur😄
sekarang lg rame2nya energi terbarukan.semoga di bahas lg tentang inverter kedepanya.seperti halnya clasd sa.at ini
Whay use 2 inverter stages? Wouldnt it be much easier if Simply boost the 12v to 300or 400v and then Use EGS Hbridge to make it a Sin wave? Anyway awesome build
How to adjust VFB Voltage, because when we try to adjust the output goes to shutdown.
Boss skli2 upload pilihan ampli terbaik versi smean🙏👍
Hello! Good work! But why a litz wire consists from such thick wires? When I made AC/AC HF converter from galogen lamps (300W) I had unsucces with thick wire 0.33millimeters. A transformer was too hot and a current density was roughly 2 A/mm2. When I change my homemade litz 0.33mm on 0.16mm the temperature of wire had been decreased much. It was a construction like a steel rope. 12 wires was a minimal twisted wire unit. These wires (5 unit) twisted into one - e.t.c. A current density was 4A/mm2.There wasn`t any cooler.
Can it feed back into the grid?
Hey, how do you choose the RC combination you used for the SG3525 from compensation pin (pin 9) and inverting input (pin 1). As there is not much information about how to calculate it on the internet so pls if you could help me out 🙏
Good Work brother
Lo felicito siempre con proyectos profesionales, muchas gracias.
Mas sistem kerja sinusoidnya inverter sp2500 itu gimana yo. Masih bingung bagian mosfet out setelah cap dc 400v nya saya
hello friend thanks for sharing your project. I have a question. I am setting up this project in my country, the ac voltage is 120v. then the DC volage is how much 220 dc so that the output can modify it to 120v ac.
@Wahyu Eko Romadhon
Hi, congratulations!! Could you tell me if have you experienced any issue or problem with the LP filter?. Did you have any problems with L-C resonance? I have been working on a prototype using EGS002 (also using a compatible pinout board based on a PIC that I have been working on) and in both cases I had some problems with LCL filter. It seems that at resonance frecuency, there is a lot of energy and I can see high current peak across the capacitor in paralel branch, wich still remains if a limiting series resistor is added. I think it could be a matter of choosing the resonance frecuency which should not to be close to a (sub) multiple of switching frecuency (in EGS002 switching frec is around 22-23 KHz, in my board it is 25 KHz), but unfortunatelly I am not sure about it. I will aprreciate any comments about this subject. Thank you very much.
After 2 years,did you solve the problem?
Great video Sir .... Thanks for sharing .... I need to small help .... The EGS002 Have any settings for HIGH FREQ (380VDC to 220VAC) .... The EGS002 Used Low frequency inverter also 12VDC to 220VAC ..... How to H Bridge Switching will work Please ....
Hi, what is the maximum surge power and how many secs of surge power can it handle? Thank you
It is at the bottom of the page but cannot be clicked. Gerber and file parts are clickable.
Fantastic work, I appreciate you doing it yourself and I hope you have to have more beautiful 🤩 today
Never use totem pole driver for high volt boostrap ground connection it will break down very fast use optocoupler isolation and use half bridge driver ic or just the optocoupler
Hello what is you frequency of the sg3525's pwm ?
Mantap terus berinovasi untuk umat👍👍👍👍👍
Belinya dimana yang siap pakai ?
mas eko itu lem apa ya yang dipake di toroid penasaran terimakasih mas
yang stage pertama utuk switching mengunakan sistem buck bost converter / sistem phuspul untuk inverter step,up nya mas..?
Tanya mas Wahyu..saya liat skemanya itu min elko 400V dengan min dari aki nyambung jadi satu ya??misal kepegang nyetrum gk ??
All your projects and videos are really interesting. Which video editing software are you using to make videos?
Adobe premiere
@@WahyuEkoRomadhon Thank you :-)
Is it still working after 4 years?
mas j gnd itu disambung kemana mas? kemudian Rsense nya berapa K ?? bingung aku iki
Hello again.there is a resistor named (sens) in this board what is that for and what the range of it ...in fact what is range for (sens) resistor in board for 24v...tanx.i dont know why i don’t have 3525 pwm pulse on my mosfet pins
Kalau beli sdh jadi di mana ya? Tolong infokan
Such a great project well done, Making synchronization of inverter could be a great idea to connect multi inverters parallel
Coba mas buatin project induction heater deh kayaknya menarik di terapin buat seperti kompor induksi gitu....,saya ingin belajar mas 😁
Klo gk ada totem nya rekom gk mas?
Hi bro nice work! Can i ask a question?
Is it possible the shift the phase of the inverter?
Untuk 48v bisa ini mas perubahan komponennya banyak gak
Info boss stage 2 pake IGBT apa Mosfet & seri nya berapa...
Please present the circuit diagram in such a way that you can clearly see
sllu nyimak,smoga trus sehat rjki ny sllu brtmbah.
Amiinn thanks
Admin..How can I add IGBT to this design
Mas pcbe sampyan ono tulisane sense ambik j gnd secondary gae opo?
Donat'e kayak'e enak enek susu ne😁😁
Mas Wer kapan2 bikin Inverter Hybrid...
Tapi ini udah sangat joss banget 👍👍
Hbis ni nnt mas. Hybrid dr pln didckan pke pfc buck boost. Di campur out dc step up. Bru diegs. Klo hbryd sinkron ac rumit mas
@@WahyuEkoRomadhon Ok mas 👍😁,,
Memang rumit sih,, apa karena kerumitan nya yg nyebabin harga Inverter Hybrid sangat mahal...
Mungkin mas. Tapi sbnere masih rumitan smps yg pfc fb mas dbnding invrtr hf ini.
@@WahyuEkoRomadhon hahaha 😁,, Klo SMPS FB+PFC saya masih agak bingung karena saking banyaknya komponen yang gak boleh asal-asalan 😁
Saya tunggu video2 selanjutnya mas,, suka pas pengujiannya👍😁😁
Siapp mas. Thanks jg udah mampir 🙏
hello
i'm making this inverter
pls can you tell me what is the value sens named resistor
and the resistance of shunt.
Mantab.....ditunggu yg 5kw
sir, I am from India, cant find ferrite core transformer 63mmx36x25mm (by your instruction in video) , what can i do ? please reply
It draw a very high current on a input side I think the 50A fuse might be burn up.
Put twice
Kalau mau beli dimana mas
klo mo naikin daya main dimananya bang?
Can you please tell me what is the value of EMI Filter inductance
Use TDK EE-55 ferrite core more efficient brow...i got 93% eff based on egs002 high freq
Watt out?
What is the output wattage ?? And can you pls share the schematic and transformer winding detail it would be really helpful :)
Bang bisa ga modif inverter high frequency 500watt jadi 1000watt atau 1500watt
@Wahyu Eko Romadhon hello friend thanks for sharing your project. I have a question. I am setting up this project in my country, the ac voltage is 120v. then the DC volage is how much 220 dc so that the output can modify it to 120v ac.
Cant sir cause using egs002
@@WahyuEkoRomadhon I am putting together the same of your inverter project from 24v DC to 120v ac. I have to make the modifications to the voltages. My question for the step-up voltage of how much is it from 24 to 220v DC and 220 DC to 120v ac. my question if it is ok in the first stage. Thank you
Hai, Mengapa inti ferit menghabiskan begitu banyak arus DC? dengan beban dan juga tanpa beban? /// hi, Why is the ferrite core spending so much DC current? with load and also without load? /// ওহে, ফেরাইট কোর কেন এত ডিসি কারেন্ট খরচ করছে? লোড সহ এবং লোড ছাড়াও? /// Thank's!!!!
Hello again.I try to made this nice project I’m on made ring fritte ...i used 2*4 turn for primary and 65turn for secondary and then i don’t know for two other out put how to turn ...i use 3turn and 3 turn again but when i connect it to board i have dc 380volt well but my 8 *fr207 start to hot so much and my step down module start hot much ...!!!
Use step down voltage external
Mas itu frekuensi nya smpai 400 hz ya mksdnya
wih mantap tenan, mas eko,, dan akan lebih jos lagi kalau ada penjelasan nama komponen komponennya dan penjelasan laiinya,, jujur mas suara musik nya agak sedikit mengganggu, mungkin akan lebih keren dan sangat bermanfaat jika suara musik itu di ganti dengan suara penjelasan jenengan dari semua aktifitas yg di buat,, ,, oh iya ada no contak atau wa kah,,sy mau konsultasi atau pesan barang barang yg sudah mas rakit..
Iy mas nnti klo sdah trsedia pcb sy gnkan bhs indo utk tutorialnya. Dn utk pmbelian pcb sya beri kertas panduan.
Sir, can i use this with both 12V and 24V DC input,
Does this circuit haa short circuit, under voltage , over voltage protection,
I need more details about this
Yes it can bro, yes all fitur that u mean includes
Ha Ha Ha Ha, almost 80% persons who deals in electronics are smokers.
Now to the topic. Good project with almost complete details. Thumbs up.
Hehehe agree with you 😁,
Ada yang sudah jadi gak bang?
Coba buat cdi racing mas
Mas bro, resistor SENS itu dikasi yg berapa ohm??
Inverter nya bisa di modifikasi menjadi 2000watt
Gracias desde República dominicana
Does it have short circuit protection ???
Yes
Which type of protections are ther in it
Berapa nilai induktor untuk stage 2 bang
Hi. The schematic download section at the bottom of the page is not disabled and clickable. Check it if possible. Thankful.
Now check it
@@WahyuEkoRomadhon Hi. I checked again. Again, the schematic is not downloadable and cannot be clicked. Apparently it is possible to download.
Mas kalo frequency nya mau ac 220v 200hz bisa ga mas?
Untuk menyuplay trafo 30amp 82vac mampu maksimal tidak bang?
Saludos sensei como siempre buen proyecto en inversores
Jijal gowo batrai abc mas😀😀
Vc é o caraaaaaa parabéns pelo projeto....
link pembeliannya dimana nich produk nich inverter 1000 w ... kita dukung mas pokokke .. ngopi sek ojo lali....
The fans are way to loud. If you mount a single much larger fan above the board cooling from above you could get silent running.
No its not silent fan .. still loud 🤣
mantap dji sam soe..... usssst ahhh..
Surya loper mas
Mas buat inverter plus charger
Jadi ketika inverter digunakan bisa mengecas aki itu sendiri
Ini lg buat mas. Tpi cas utma pke solar pnel
@@WahyuEkoRomadhon Ooooo
Gitu terus semangat berkarya
Yang tinggal pakai ada g mas 😀😀
Sir what is this- fc-a2012bk-470h2 ?
mas bikin yang 7.1 channel donk.. yang 5.1 luar biasa sekali..
Bang ada link pembeliannya gak
Hi. I checked again. Again, the schematic is not downloadable and cannot be clicked. Apparently it is possible to download.
Okay i will fix it now
@@WahyuEkoRomadhon Hi. fixed . Thank you so much .
Explain the purpose of the 3 relays in the circuit. Thankful
Kalau bisa buat banyak bang, trus inverternya dijual di tokopedia pasti laku, soalnya sya pengen beli jg wkwkwkwk
Apkah ini djual di lapak omline??
Untuk mndPatkan produk ini beli lapak apa mas???
Sperti video mas ada
Great inverter Man.
TKS for shering.
Hug's
Hi friend
How much Input Current when No Load?
i saw about 4.7A
0.4A / 400mA the idle current. , in video 4.7A with load 60W soldering iron and 50W lamp. You can see output current.
@@WahyuEkoRomadhon
Thank you friend.
i love all your work 👍
Maknyuss arit e 🤭
Rumit..... Tapi berhasil.... Mas eko emang gene 👍👍👍
Wah ada Bli Agung juga 😄Dari Bali Ya Bli
@@electroniccreative7683 ya betul mas..... Hobby nyolder juga
@@agungoka482 mantap.. Saya deketnya Monang maning.. Deket SMPN7 Bli 😃
cool very good your work.
friend you have video of how to calculate the ferrite transformer ?
you can see previous dc to dc step up
Hello again.i made this project completely.
Now i have two problem...one-> my hi volt fet(23n50) near inductor start warming to hot with out any things connected for run or light(i use about 3mh inductor)
Two->when i connect a fan or light to out put 220vac start to down and then turn off and inverter module restarted.why?
All things start true and good and out put is sine wave good but i don’t know why that two problems happen!,,!
I use 24vdc20a power to run.
Can you help me to solve?tanx
Set UVP under 20V
Idle current besar sekali gan, 4A ya?
0.7A gan
unboxing ngeri mas nganggo clurit. hehehe
Anti mainstrem mas kwwk