you are skipping some parts in the process have to mention this as a newbie will get confused like I did lmao. but still very informative I managed to do the task in the end with your help
Ooooh .... this is nice. Last time I tinkered with my Linksys 1900(ACSv2 Dumb AP) and 3200 (ACM, primary) you cannot mwan ethernet ports only USB. Thanks much!
Hi Van Tech Corner, Do you have your own documentation, or documentation that goes into more detail about "OpenWRT Load Balancing with mwan3". Not only the "install / configuration" but also all the other features it has.
very good tutorial. Now wanb needs to be atached to a bridge otherwise it won't connect. Also I need help with UPNP that stoped working after this is configured...
Well, that is a lot of calculation. If you just get started to mwan3, you better follow my video to get it work first. After that, check the official mwan3 document and learn how to adjust it. Here is the key points: - Member interfaces with the same metric will be load-balanced - Load-balanced member interfaces distribute more traffic out those with higher weights openwrt.org/docs/guide-user/network/wan/multiwan/mwan3
@@VanTechCorner yes I followed your instruction and it works well, but since it has different bandwidth for WAN and WANB, the result is not very satisfy for me. . but anyway thanks for you answer, I will look at your link to get more clear. thanks
Thanks for the video. I have two wan (2 connection from 2 different ISP) load-balanced by mwan3, how can i setup wiregurd vpn so my ip address remain same? cause in my current load-balanced scenario my public ip address change frequently. Thanks a lot
all settings for wanb connection are valid - i tried to run it on wan device and everything was fine. but on lan1.35 - Connection Attempt Failed all the time
Ad ơi cho em hỏi là em tạo được 2 đường wan từ 2 đường intenet khác nhau rồi giờ em muốn tạo ra 3 mạng wifi 1 cái lấy đường wan 1 1 cái lấy đường wan 2 và cái kia thì gộp của cả 2 đường được không ạ em muốn làm vậy để backup khi mà sự cố mất 1 đường hoạt khi mình chỉ muốn sử dụng 1 đường ấy ạ mong ad trả lời ❤❤
hi , i like your videos nad i have a question , can we use loadblancing and wireguard VPN as client in the same time with maximum bandwide? cuz i tryed but every time wireguard just using one of my wans and didnt use full bandwide of my wans
Hello, Wireguard will establish the connection to 1 endpoint IP (server) thus it will be using just 1 WAN connection. You can play around and try to create the load balance of 2 wireguard interfaces, but I have yet to test if it is working.
@@VanTechCorner mwan3 was designed for physical interfaces, but seamlessly accepts virtual interfaces. I've had it working with a 1 gig Fibre optic PPPoE connection using a vlan, and as second WAN a 4G mobile hotspot adapter connected via usb. When downloading large raspberry pi images using bittorrent, it used both adapters to maximum bandwidth, that was cool to see, 150 Megabytes per second transfer
hi, thanks for your video, just a question, when i tried to create a new interface, in my devices section i d'ont have lan ports separately, can you tell me please how can i fix it ? openwrt 21.02
Followed the tutorial. Wan6 and Wan6b appear online in loadbalance status. However in Windows the status of the ipv6 is "No internet access" and performing the testipv6 it appears that I am not with it active. What's the problem?
@@VanTechCorner Hi, In my current setup, I have a ISP terminated on a Switch, to which Raspi Openwrt and a WiFi router is connected....To the same switch I wish to connect a WiFi Dongle to create a redundancy
Hi, I have a Newifi router running with openwrt 19.07.4. I installed MWAN3 software to configure a Dual-WAN FAILOVER from WAN to WAN2 I also installed NFTABLES software to configure BANDWIDTH LIMIT PER IP. Now here's the catch and also my problem, - I want the WAN to perform at full speed of bandwidth which doesn't have any problem in my experience ✅ -I want to configure the WAN2 with BANDWIDTH LIMIT PER IP when WAN lost its connection. Now, when I configure BANDWIDTH LIMIT PER IP on NFTABLES it applies to WAN and WAN2 which is a pain in the *ss 😑 My question is. Is there a way that NFTABLES applies only to WAN2 for BANDWIDTH LIMIT PER IP while WAN is in full-speed?
Sorry I can't help you with this as this is too advance. Either you should go to the OpenWRT forum or contact the maintainer of the package for further information.
Hello,I would like to ask a question, the openWrt router is configured with a lot of wireguard protocol VPN WAN ports, and then I use Mwan3 to split the traffic, so that a specific internal IP goes out through a specific wireguard WAN port, everything runs normally, but there is a small problem that the router has just turned on For about 10 seconds, before Mwan3 is automatically loaded, the all traffic will go out through the default local ISP WAN port. Is there any solution to make the router go out through the WAN port of the wireugard protocol as soon as it is powered on, and never go through the local ISP WAN port? .Thank you so much.
Set br-lan to delay startup, and wait for all interfaces of wireaguard to start up and Mwan3 to be loaded before starting br-lan. Is this solution ok? But I also don't know how to set br-lan to delay startup for about 1 minute.
@@rowelbarrios4945 Yes it is normal as mwan3 doesn't combine the throughput of all your WAN interfaces. Also, check the CPU usage during the test. Perhaps the CPU reach 100% usage with slow down the speed.
Hi, actually you can configure the load balancing on the EdgeRouter X with the Web UI. Everything is automatically configured and you just need to do that from the Setup Wizard. However, if you want to install OpenWRT on this device, here is my video guide ruclips.net/video/VreMamhWOX8/видео.html
@@VanTechCorner But with certain applications, like torrent clients and Steam, you would get download speeds that are (more or less) a sum of both internet connections, right?
Sir help me pls why my mwan just can workin on speedtest i try for watch youtube and download any files it not worked and just using 1 interface but in the speedtest it can use 2 interface and balanced pls help
The problem is that your application (RUclips) doesn't support multiple connections. Mwan3 only load balancing, it doesn't bound all available throughput of the 2 interfaces.
hello i have pppoe(main) and static ip i need to multi connection to login to static ip with pppoe stay connect ...... The all connection from same port wan(eth0)
Hello I have a router Xiaomi ax3600 with openwrt. Previously i had no broadband connection on my home. But my next door neighbours wifi password (They gave me) I knew so I was using my router as a wifi repeater and used wifi more than a year with no problem. Their line speed is 20 mbps. Recently i bought home broadband line myself. That is also 20 mbps I was thinking can i combine both line via openwrt. As my router is very capable. So i was thinking Like using fiber cable 20 mbps + neighbours wifi repeater 20 mbps = 40 mbps Is that possible? If possible can anyone guide me please!
Thank you, this helped me get a mockup network working with redunant wan connections!
What good videos you make!
you are skipping some parts in the process have to mention this as a newbie will get confused like I did lmao. but still very informative I managed to do the task in the end with your help
Ooooh .... this is nice.
Last time I tinkered with my Linksys 1900(ACSv2 Dumb AP) and 3200 (ACM, primary) you cannot mwan ethernet ports only USB.
Thanks much!
You're welcome!
Thank you very match for all clips about Openwrt.
Hi Van Tech Corner,
Do you have your own documentation, or documentation that goes into more detail about "OpenWRT Load Balancing with mwan3". Not only the "install / configuration" but also all the other features it has.
Good.
BTE, what is the advantage for making ports as VLANs?
bác nói tiếng anh giỏi quá
thanks! awesome video
very good tutorial. Now wanb needs to be atached to a bridge otherwise it won't connect. Also I need help with UPNP that stoped working after this is configured...
Hi, Is it posiible to add email notification when wana or wann is down?
Hi, van tech corner, great tutorial. I just wonder, what if the bandwidth of each port is not equal, can we still load balance it?
Yes, but in this case you should set the correct weight & metric for the interfaces.
@@VanTechCorner that's what I want to ask, can you give me example
Well, that is a lot of calculation. If you just get started to mwan3, you better follow my video to get it work first. After that, check the official mwan3 document and learn how to adjust it. Here is the key points:
- Member interfaces with the same metric will be load-balanced
- Load-balanced member interfaces distribute more traffic out those with higher weights
openwrt.org/docs/guide-user/network/wan/multiwan/mwan3
@@VanTechCorner yes I followed your instruction and it works well, but since it has different bandwidth for WAN and WANB, the result is not very satisfy for me. . but anyway thanks for you answer, I will look at your link to get more clear. thanks
Could you post a video using Wireguard Multi-WAN Load Balancing with mwan3?
Is there a way to set-up a policy or rule to start a VPN if let's say WANB is used but no VPN if WAN?
Thanks 👍 for the video.
How to manage some network plan GBs Limit and date for reset per WAN
Hi any issue with internet banking if using 2 isp with LB? Afraid suddenly change to other isp during login internet banking.
Do you plan to do a failover setup updated to 21.02 or is it basically the same as the old video?
its the same
Thanks for the video. I have two wan (2 connection from 2 different ISP) load-balanced by mwan3, how can i setup wiregurd vpn so my ip address remain same? cause in my current load-balanced scenario my public ip address change frequently. Thanks a lot
I have firmware and need your help to build openwrt firmware.
So, after I create the wanb port as PPPoE, enter the PPPoE login details, I get an error saying Connection Attempt Failed. Where am I going wrong?
same problem here
did you solve it?
all settings for wanb connection are valid - i tried to run it on wan device and everything was fine. but on lan1.35 - Connection Attempt Failed all the time
Haha, I gave up... LONG BACK..
Ad ơi cho em hỏi là em tạo được 2 đường wan từ 2 đường intenet khác nhau rồi giờ em muốn tạo ra 3 mạng wifi 1 cái lấy đường wan 1 1 cái lấy đường wan 2 và cái kia thì gộp của cả 2 đường được không ạ em muốn làm vậy để backup khi mà sự cố mất 1 đường hoạt khi mình chỉ muốn sử dụng 1 đường ấy ạ mong ad trả lời ❤❤
My public IP is changes continuously. One it changes to "wan" & then it changes to "wanb"
Hey, did you solve the problem?
@@VanTechCorner Un tick this option "Enable Application Optimized Routing". At Transmission > Load Balancing
Great vid, sir. Pls, how to mitigate https traffic under mwan constantly loosing connection, like corporate office365 , ms dynamics and others.
hi , i like your videos nad i have a question , can we use loadblancing and wireguard VPN as client in the same time with maximum bandwide? cuz i tryed but every time wireguard just using one of my wans and didnt use full bandwide of my wans
Hello, Wireguard will establish the connection to 1 endpoint IP (server) thus it will be using just 1 WAN connection. You can play around and try to create the load balance of 2 wireguard interfaces, but I have yet to test if it is working.
@@VanTechCorner mwan3 was designed for physical interfaces, but seamlessly accepts virtual interfaces. I've had it working with a 1 gig Fibre optic PPPoE connection using a vlan, and as second WAN a 4G mobile hotspot adapter connected via usb. When downloading large raspberry pi images using bittorrent, it used both adapters to maximum bandwidth, that was cool to see, 150 Megabytes per second transfer
Thanks for the informative update, Paul!
hi, thanks for your video, just a question, when i tried to create a new interface, in my devices section i d'ont have lan ports separately, can you tell me please how can i fix it ? openwrt 21.02
May I know the router model? Maybe your device is still using swconfig, if yes you should see the Switch menu in Network section.
@@VanTechCorner thank you for the answer, i have a Tp-link Archer C7 v4, unfortunately no DSA
Followed the tutorial. Wan6 and Wan6b appear online in loadbalance status. However in Windows the status of the ipv6 is "No internet access" and performing the testipv6 it appears that I am not with it active.
What's the problem?
Did you get the IPv6 connection up and running before settinh up mwan3? In order word, does your ISP support IPv6?
@@VanTechCorner Yes both ISP provide ipv6 and work on Openwrt or other system. But when performing the mwan3 this happens.
HI Van,
Please guide on how to use Raspberry PI 4 B as OpenWRT 21.02 - Multi-WAN Load Balancing with mwan3
Hi, how are going to setup the Raspberry Pi 4 ? It only has 1 Gigabit Ethernet port.
@@VanTechCorner
Hi,
In my current setup, I have a ISP terminated on a Switch, to which Raspi Openwrt and a WiFi router is connected....To the same switch I wish to connect a WiFi Dongle to create a redundancy
What will happen if one of the WAN port has no internet connection..?
Hi, I have a Newifi router running with openwrt 19.07.4.
I installed MWAN3 software to configure a Dual-WAN FAILOVER from WAN to WAN2
I also installed NFTABLES software to configure BANDWIDTH LIMIT PER IP.
Now here's the catch and also my problem,
- I want the WAN to perform at full speed of bandwidth which doesn't have any problem in my experience ✅
-I want to configure the WAN2 with BANDWIDTH LIMIT PER IP when WAN lost its connection.
Now, when I configure BANDWIDTH LIMIT PER IP on NFTABLES it applies to WAN and WAN2 which is a pain in the *ss 😑
My question is. Is there a way that NFTABLES applies only to WAN2 for BANDWIDTH LIMIT PER IP while WAN is in full-speed?
Sorry I can't help you with this as this is too advance. Either you should go to the OpenWRT forum or contact the maintainer of the package for further information.
Hello,I would like to ask a question, the openWrt router is configured with a lot of wireguard protocol VPN WAN ports, and then I use Mwan3 to split the traffic, so that a specific internal IP goes out through a specific wireguard WAN port, everything runs normally, but there is a small problem that the router has just turned on For about 10 seconds, before Mwan3 is automatically loaded, the all traffic will go out through the default local ISP WAN port. Is there any solution to make the router go out through the WAN port of the wireugard protocol as soon as it is powered on, and never go through the local ISP WAN port? .Thank you so much.
You can see the Kill Switch. openwrt.org/docs/guide-user/services/vpn/wireguard/extras
Set br-lan to delay startup, and wait for all interfaces of wireaguard to start up and Mwan3 to be loaded before starting br-lan. Is this solution ok? But I also don't know how to set br-lan to delay startup for about 1 minute.
Is it okay to update packages? Or it can can conflict in your recent configuration?
As I know, the config files of the package will be the same and I never have a problem when upgrading them.
@@VanTechCorner Is this normal? I have 20Mbps in WAN1 and 20Mbps in WAN2 but when I'm trying to speedtest I can get is around 25Mbps only.
@@rowelbarrios4945 Yes it is normal as mwan3 doesn't combine the throughput of all your WAN interfaces. Also, check the CPU usage during the test. Perhaps the CPU reach 100% usage with slow down the speed.
Thanks
I'm considering putting OpenWRT on my Edgerouter X because of mwan3.
Hi, actually you can configure the load balancing on the EdgeRouter X with the Web UI. Everything is automatically configured and you just need to do that from the Setup Wizard. However, if you want to install OpenWRT on this device, here is my video guide ruclips.net/video/VreMamhWOX8/видео.html
it works great. Recently i have issues about https traffic sessions loosing connection . Must figure out how to balance it in order not shatter it.
can you please explain how i can allow particular protocol use a particular gateway
Hi, you can take a look at the "customs routing" tab. It allows you to configure the gateway base on IP & protocol.
Hi, is that combining the 2 wan bandwidth?
Nope, it is load balancing. 1+1=0.5+0.5+0.5+0.5, not 1+1=2
@@VanTechCorner But with certain applications, like torrent clients and Steam, you would get download speeds that are (more or less) a sum of both internet connections, right?
I wonder how it will work with dynamic DNS and port forwards?
You can create custom routing and select the interface on the "Rules" section of the mwan3 application.
Sir help me pls why my mwan just can workin on speedtest i try for watch youtube and download any files it not worked and just using 1 interface but in the speedtest it can use 2 interface and balanced pls help
The problem is that your application (RUclips) doesn't support multiple connections. Mwan3 only load balancing, it doesn't bound all available throughput of the 2 interfaces.
@@VanTechCorner is it possible to streaming video with multiple connection sir? Do u know what plaform that support it?
@@comcom9342 you need to have a Virtual Private Server with OpenMPTCPRouter to be able to do what you're asking
hello i have pppoe(main) and static ip i need to multi connection to login to static ip with pppoe stay connect ...... The all connection from same port wan(eth0)
Hi, I am not really get what your mean? Can you provide more info about the network diagram.
how do you setup a dual Wan with a 4gLTE modem and a dedicated wan port?
Still the same setting, you just need to specify the correct interface name for that 4G connection.
@@VanTechCorner im not sure how to process the ipv4 / v6 do i create two interfaces like a lan/wan connection?
Nice i'll try it on openwrt redmi ac2100 fw21
Hello I have a router Xiaomi ax3600 with openwrt. Previously i had no broadband connection on my home. But my next door neighbours wifi password (They gave me) I knew so I was using my router as a wifi repeater and used wifi more than a year with no problem. Their line speed is 20 mbps.
Recently i bought home broadband line myself. That is also 20 mbps I was thinking can i combine both line via openwrt. As my router is very capable. So i was thinking Like using fiber cable 20 mbps + neighbours wifi repeater 20 mbps = 40 mbps
Is that possible? If possible can anyone guide me please!
how to add ap client loadbal...
Hola Bonding Openwrt ?