Thanks! I'm never afraid to fail as that is usually the best way to learn. I wanted to share what I learned so that others don't have to do the same mistakes. Also its good reminder that everything doesn't always go according to the plans.
Props to this guy for showing the imperfections of his process. EVERY other channel likes to show how perfect they did something by editing out the mistakes.
The Motodane 本種 stamp suggests a Kagoshima maker. This practice goes way back when scissors made by Tanegashima Kagoshima forgers were popular, and Sakai makers started copying them. In response, Kagoshima makers started to put this 本種 mark on their products to differentiate them. Hondane means True/Original Tane, with the Tane 種 representing Tanegashima 種子島.
choinka d not sure if you’ve tried or not, but turning your screen setting to Night Shift on (Night Mode, Night light, etc), basically disabling blue light on your phone, which makes eyes less tired and helps increase melatonin (the sleepy chemical). That way if you watch a video, you’re more likely to fall asleep better after it.
"A quick note on machi gaps... I know that many on here do not like them, so i thought i would take some time to explain a bit about them. First, the biggest thing to know is that there are regional differences in aesthetics. Kanto tends to like large gaps, while kansai does not. However, most knife makers/retailers/wholesalers in japan will still leave them if it makes more sense to than not. However, on request from many us retailers, many wholesalers in japan have started installing the handles flush with the handle. So, the question becomes "why leave a gap?" There are a few reasons the gaps are left... here are some of the top ones -When the neck of the knife is short (which can happen for a variety of reasons or sometimes none at all), the spacing between the choil and the handle becomes important. This space should be large enough to fit about 80% of your middle finger when holding the knife in a pinch grip. Smaller than this will be too small and is uncomfortable to hold. Larger than this will be too loose and can make rotary control of the knife more difficult than it should be. 80% or so gives enough space for the finger to fit, but is tight enough that the finger is still in contact with the handle for rotational stability. Also, what i have just said is based on what one would expect for a gyuto. Ideal sizes will be different based on knife types, expected grips, intended customers, etc. -Handle installation... This is not only for ease of installing handles in the traditional japanese way (which is easier than using epoxy, allows for easier handle replacement, and removal of handles for maintenance), but also allows for knife placement relative to the handle. Knives with no machi will have a spine that is significantly lower than the top of the handle for example. On significantly harder woods (like ebony), the tang with the machi makes installation significantly easier with less chance of the wood cracking (which can be a problem with ebony). Here are the top reasons i hear for people not wanting machi gaps... -Food gets stuck. I've used knives with machi gaps for many years, both at home and in professional kitchens. This area is almost always covered with your hand and is not generally at risk for food getting stuck. If food does get in there, its a long way from being stuck, and comes out with general knife cleaning. If you find food accumulating, the chances are you may not be taking care of your knife well enough in my opinion. I've seen a wide number of knives from a wide number of people. I see just as many very dirty knives with no machi as i do dirty ones with a machi. I would venture to say, a dirty knife is more a function of the user than the knife design. -It catches on your finger. I've found this to be the case with very large machi gaps or on some lower end knives that have machis that extend beyond the handle in width (or height depending on how you think about it). However, after significant testing, i've found that on knives with normal sized machi gaps, if this turns into a problem, it is most often the result of the use of an improper grip. When knives are held properly, your fingers dont really make contact with this area in a way than can catch. -And of course, some people just dont like the way it looks... actually, this one is the reason i understand best. The reason i say this, is that sometimes i ask makers to reduce or remove the machi gaps based on customer requests. However, i have a stipulation i have discussed with them. I would prefer that if and when they reduce the gap, they do it to an extent that does not sacrifice the ability to grip and use the knife well. Anyways, hope this helps make sense of this to some of you." by Jon BROIDA www.kitchenknifeforums.com/threads/a-note-on-machi-gaps.13481/
These types of videos are so much better when people don't add music to them. This was strangely relaxing to watch. Amazing job with the knife. I have a japanese knife that needs some restoring, this gave me some ideas.
I’m not a fan of the clear resin portion of the handle but I have to admit that I love the creativity. I would gladly use that in my kitchen. You’ve earned yourself a sub! 👍
I dont think he used enough resin. That space between the blade and the handle is just a little bigger than I'd like for myself, but I also can't make my own knife.
There was a moment (when I saw the failed resin casting) when I went from completely confused as to what you were doing with the handle to "ohhhh, now I see what you're going for". Not something I would ever have thought of doing. The smashed wood reminds me a little of a Japanese art form I've heard of involving fixing broken porcelain with gold, so that the repairs are conspicuous and form part of the intended look of the piece.
I know it's been sooo long since you did this video but now that my mother asked me if i could restore her oldest kitchen knife, i wanted to learn from the guys that really know how to do it. Now i have an idea although i'm not even expecting to achieve not even 10% of your quality. Tons of thanks and best regards from the corner of the world, Argentina!
That was extremely creative what did you with the handle, looks really beautiful. Thanks for your videos! I really love them and enjoy learning from you 😄👍🏼
This is a stamp. The manufacturer will write down the brand name, author name or trademark. "HON-TANE" is probably produced by "Ikenami Cutlery Works" in Tanegashima, Kagoshima, Japan.I am glad as a Japanese to have you repair it with wonderful techniques. Please use it for a long time.
it's so beautiful and you saved the aesthetic and history of the knife. would've definitely bought this for a personal collection, such a decent tool to use!
Greetings, Vladimir here with NTD Television. We are one of the world's fastest growing media companies with over 100 million fans and 1 billion monthly video views across all of our social properties. Our motto is truth, hope, and humanity. Our team was very impressed by your video and our editors would like to showcase it by uploading it on some of our social media pages and websites so that our fans can see it. Of course, we are happy to credit your channel clearly to make sure people know how to find you and your videos. You will still hold the exclusive rights to the video. Can we have your permission to do that? Kind regards, Vladimir
I love seeing tool restorations of all types, but older chefs knives in particular and this was a delight to watch with the materials involved. An amazing finish, better than the original by a mile, a delight to watch. Can I ask what type of wood you used.
Beautiful job! I don’t have power tools but did manage to restore an old axe head using vinegar, steel wool, sandpaper, metal files, sharpening stones, time, and effort. After fitting the head on a new hickory axe handle from Costco it looks and works nicely. It’s a simple thing I know, but very satisfying to see “trash” become like new again.
Why did people disliked the video? Even if he did something you didn't like, he yet did a great work. It wouldn't be better if you supported him with a comentary telling what he can improve?
Nice restoration, though I'm not a fan of the resin part. I feel like it would have been better to do it the way it was done originally. But it does show creativity. So how about making a knife and/or forging one yourself rather than just restoration? I think that would make an interesting video.
"I like the restoration but blah blah the handle... I would have done this instead...." Oh ok, so where's the video of you beautifully restoring something? LOL! Great job, diy cool stuff!
Yeah ... that's not how it works. If you go to a restaurant and they serve you a terrible pizza you can easily tell it's terrible, you don't need to know how to bake it to express your opinion about it. If something is bad is bad regardless of the fact that you can do it or not. In my opinion he did an awesome job, I just used an example to get my point across
what was the reason for them to do it? give me the same reason and i will, constructive criticism is always a good thing when not pushed, they still have the knife, they could relatively easily do that, it's just a bit of a waste since it's so good already, depends how much of a perfectionist they are and how well they like the knife, i can't do much of this, that is, i have no experience with it, now i could give it a shot if enough people wanted to see, but for a knife that will be used 3 times then rust, i don't see much point, you can't really sell things around here, so it would be a beautiful thing that would go to waste, and that's even if i bought all the tools (i kinda need them for other things anyways, so it's not that big of a deal, just money, money i don't have, otherwise i would have boughten the tools already, and i would need to know the amount of blue they used, or i would need to make a different colour, maybe a red or yellow one like fire or something? ice is far more believable and realistic and nice of course, and to get the ice like colour, i would need to get a blue whatever that stuff is and try a few times till i got the right colour, that's if i got the right blue even, i wonder how much of the resin i would need to use for testing? i wonder how much comes for $30, see why it would be much harder and not really reasonable for others to do it? youtube recommended this video, but i'm sure mine have never been recommended, even if i did the same thing
I admire and respect the restoration, however I prefer the traditional look. I’m also not a fan of a gloss finish on wa handles. But it’s pretty cool. For anyone questioning the handle depth, Japanese knives with wa handles usually expose a large part of the tang creating a larger Choil. This benefits the pinch grip most (including myself🙂) chefs prefer for comfort on these blades. For me the position is on point.
And Tanegashima Island is traditionally known as the site of the introduction of European firearms to Japan in 1542. So, Craftsmen in the island have kept alive traditional techniques for forging and sharpening iron tools.
Amazing content. Thanks for sharing and explaining your errors and trial. I learned so much just from watching your videos. I’m always curious about how products are made. For you to show your crafty skills restoring it, gives me much knowledge. I am entertained. Keep up the great work, thanks again for sharing. You are awesome.
Love your restoration projects. Was cringing a bit while watching you sharpen the blade though . Japanese knives should be sharpened on special Japanese whetstone of progressively finer grit. These stones are kept soaked in water.
It's cool that you're not afraid to show the first failure with the handle. The result is very beautiful!
Thanks! I'm never afraid to fail as that is usually the best way to learn. I wanted to share what I learned so that others don't have to do the same mistakes. Also its good reminder that everything doesn't always go according to the plans.
Odd Tinkering is right
@@OddTinkering Y͎e͎s͎!!!!!!
thanks bro
@@i-_-i2080 who are you talking to
Props to this guy for showing the imperfections of his process. EVERY other channel likes to show how perfect they did something by editing out the mistakes.
What do u mean imperfections?
@@coalsauce4457 *you
Chris w he means the epoxy mistake
@@coalsauce4457 like people intentionally edited out the mistakes they'd done during the restoration job.
I had the same thought. This guy isn’t perfect at everything, but he sure schools me in all of it!
The Motodane 本種 stamp suggests a Kagoshima maker.
This practice goes way back when scissors made by Tanegashima Kagoshima forgers were popular, and Sakai makers started copying them. In response, Kagoshima makers started to put this 本種 mark on their products to differentiate them. Hondane means True/Original Tane, with the Tane 種 representing Tanegashima 種子島.
thanks for no music during the video. i love working sounds
Ishi Mazure never thought about it that way
I’ll go a step further. No music or talking....just the sounds of metal & wood being processed.
Yes I agree, i much prefer hearing whats going on.
Ishi Mazure Agrees!
I hate it
But i Just mute so Works for me
Me: I should really go to sleep earlier
Also me at 2am: *this video*
choinka d not sure if you’ve tried or not, but turning your screen setting to Night Shift on (Night Mode, Night light, etc), basically disabling blue light on your phone, which makes eyes less tired and helps increase melatonin (the sleepy chemical). That way if you watch a video, you’re more likely to fall asleep better after it.
How did you know
Its 0730 for me lol didnt sleep yet
Me rn
"A quick note on machi gaps...
I know that many on here do not like them, so i thought i would take some time to explain a bit about them. First, the biggest thing to know is that there are regional differences in aesthetics. Kanto tends to like large gaps, while kansai does not. However, most knife makers/retailers/wholesalers in japan will still leave them if it makes more sense to than not. However, on request from many us retailers, many wholesalers in japan have started installing the handles flush with the handle. So, the question becomes "why leave a gap?"
There are a few reasons the gaps are left... here are some of the top ones
-When the neck of the knife is short (which can happen for a variety of reasons or sometimes none at all), the spacing between the choil and the handle becomes important. This space should be large enough to fit about 80% of your middle finger when holding the knife in a pinch grip. Smaller than this will be too small and is uncomfortable to hold. Larger than this will be too loose and can make rotary control of the knife more difficult than it should be. 80% or so gives enough space for the finger to fit, but is tight enough that the finger is still in contact with the handle for rotational stability. Also, what i have just said is based on what one would expect for a gyuto. Ideal sizes will be different based on knife types, expected grips, intended customers, etc.
-Handle installation... This is not only for ease of installing handles in the traditional japanese way (which is easier than using epoxy, allows for easier handle replacement, and removal of handles for maintenance), but also allows for knife placement relative to the handle. Knives with no machi will have a spine that is significantly lower than the top of the handle for example. On significantly harder woods (like ebony), the tang with the machi makes installation significantly easier with less chance of the wood cracking (which can be a problem with ebony).
Here are the top reasons i hear for people not wanting machi gaps...
-Food gets stuck. I've used knives with machi gaps for many years, both at home and in professional kitchens. This area is almost always covered with your hand and is not generally at risk for food getting stuck. If food does get in there, its a long way from being stuck, and comes out with general knife cleaning. If you find food accumulating, the chances are you may not be taking care of your knife well enough in my opinion. I've seen a wide number of knives from a wide number of people. I see just as many very dirty knives with no machi as i do dirty ones with a machi. I would venture to say, a dirty knife is more a function of the user than the knife design.
-It catches on your finger. I've found this to be the case with very large machi gaps or on some lower end knives that have machis that extend beyond the handle in width (or height depending on how you think about it). However, after significant testing, i've found that on knives with normal sized machi gaps, if this turns into a problem, it is most often the result of the use of an improper grip. When knives are held properly, your fingers dont really make contact with this area in a way than can catch.
-And of course, some people just dont like the way it looks... actually, this one is the reason i understand best.
The reason i say this, is that sometimes i ask makers to reduce or remove the machi gaps based on customer requests. However, i have a stipulation i have discussed with them. I would prefer that if and when they reduce the gap, they do it to an extent that does not sacrifice the ability to grip and use the knife well.
Anyways, hope this helps make sense of this to some of you."
by Jon BROIDA
www.kitchenknifeforums.com/threads/a-note-on-machi-gaps.13481/
What an excellent piece of infornation!
This was nice to read. I was ignorant of the fact that there was a debate at all. But the more you know I guess. Thanks
"A quick note..."
So that was a fucking lie
Jk man you're doing God's work
I didn’t understand any of it b/c I’m a kid 😭
...I was looking up what a machi gap is and I found that exact comment by “Japanese Knife Imports” on Facebook... from 7 years ago (2013)...
These types of videos are so much better when people don't add music to them. This was strangely relaxing to watch. Amazing job with the knife. I have a japanese knife that needs some restoring, this gave me some ideas.
We tear things apart when we're kids, just so that we can enjoy even more, fixing them as we grow older. Thanks you for all the beautiful videos!
I love watching these before bed it’s just soothing to hear the sounds and it’s just calming
Absolutely agree!
yeah tea it’s so nice watching it become clean
Especially when the sound is the process of fixing
Ikr
I do the same!
I love that clear resin. Looks *puts on shades* cool...........
I like the restoration and the handle however, it looks like the handle is to far back. May be just me.
It is too far back!
The handle idea is cool but it's definetely too back.
It's fine. Some knives do it that way - google "machi".
it's about appropriate for a japanese knife as far as handle placement on the tang
@@heavyg1653 thanks for the tip. ✌️🏻 Looks a little bit odd but it's a way of doing a handle in Japan.
Pleasantly surprised that the comments aren't 50% people complaining about nitpicks.
Great job man, that knife is sick.
I’m not a fan of the clear resin portion of the handle but I have to admit that I love the creativity. I would gladly use that in my kitchen. You’ve earned yourself a sub! 👍
Thanks!
be careful, this resin is not approved for food contact.
I dont think he used enough resin. That space between the blade and the handle is just a little bigger than I'd like for myself, but I also can't make my own knife.
This knife because of the resin now on the handle would cause cancer.....but only in the state of California!
That is the most gorgeous knife I've ever seen. The clear transition in the handle is a work of art.
That is the most gorgeous knife I've ever seen. The clear transition in the handle is a work of art.
I love the ice effect! for a moment there I thought what is he banging that wood for??! It became "clear" in the end. Thanx for the vid
keep restoring old tools, save our planet.. thank you.
There was a moment (when I saw the failed resin casting) when I went from completely confused as to what you were doing with the handle to "ohhhh, now I see what you're going for". Not something I would ever have thought of doing.
The smashed wood reminds me a little of a Japanese art form I've heard of involving fixing broken porcelain with gold, so that the repairs are conspicuous and form part of the intended look of the piece.
Kintsugi
Used to watch videos like these on 1.5x speed...quarantine changed that
8:10 when the vid about restoring that hammer? xd
野獣
野獣
Haha good one that😁
They probably don’t even know what they said
I know it's been sooo long since you did this video but now that my mother asked me if i could restore her oldest kitchen knife, i wanted to learn from the guys that really know how to do it. Now i have an idea although i'm not even expecting to achieve not even 10% of your quality.
Tons of thanks and best regards from the corner of the world, Argentina!
That was extremely creative what did you with the handle, looks really beautiful. Thanks for your videos! I really love them and enjoy learning from you 😄👍🏼
This is a stamp. The manufacturer will write down the brand name, author name or trademark. "HON-TANE" is probably produced by "Ikenami Cutlery Works" in Tanegashima, Kagoshima, Japan.I am glad as a Japanese to have you repair it with wonderful techniques. Please use it for a long time.
it's so beautiful and you saved the aesthetic and history of the knife. would've definitely bought this for a personal collection, such a decent tool to use!
Greetings,
Vladimir here with NTD Television. We are one of the world's fastest growing media companies with over 100 million fans and 1 billion monthly video views across all of our social properties. Our motto is truth, hope, and humanity.
Our team was very impressed by your video and our editors would like to showcase it by uploading it on some of our social media pages and websites so that our fans can see it. Of course, we are happy to credit your channel clearly to make sure people know how to find you and your videos. You will still hold the exclusive rights to the video. Can we have your permission to do that?
Kind regards, Vladimir
One word my friend: CREATIVITY! That is so awesome, like can not put in words. Thanks for a satisfying video again. Big like.👍👍👍👍👍👍
Thanks! It's good to try new things every once in a while
Most elegant restoration ever!
I have this exact knife. I bought it in Tokyo in the mid 80's and I still use it a couple of times a week. Its a great knife.
I could watch this stuff all day
As a chef it broke my heart a little when I saw the initial conditin the knife was in.
@Lifeline Bot lol it was probably a mistake. He missed an "O"
Give him a break😂
Looks neat. I love videos where old tools and sometimes weapons have new life breathed into them.
When you finished, I had this satisfaction feeling as if I did it myself :)
Seeing you take it apart was most satisfying
Now everyone in quarantine be like: *InTeReStInG*
BSP Gaming2 that’s InTeReStInG
...we are all bored in our homes durig quarantine so it ain't surprsing
@@youtubeneedstogitgud3512 - speak for yourself! I'm neither sick nor locked down
@@Charles.Wright nobody likes a show off
@@Charles.Wright you sir... are a Chad!
From trash to a prized possession. Beautiful work.
I was wondering what the hell was going on with that handle at first. Lol. Finished product is awesome! Great job!
Incredible restoration. Any chef would love to own this knife.
that resin handle part was actually quite a nice idea!
Usually don't comment on videos but this may be my favorite one out of all the restoration videos
really loved the "broken wood" handle technique.
Excellent work--thanks for leaving the first attempt to use the epoxy.
As a chef this makes me very happy,, i'd want a whole set of knives like this 😍
Very nice artwork with the resin.
Wow! I was very confused with what you were doing with the handle at first but it looks great!
Same here. Why bang away at the wood with a hammer when you can cut neatly with blade? But it came out looking really cool.
You transformed a rusty kitchen knife to a superb modern half blue knife
I really like the final result. :)
Thanks man!
Speaking as a chef... that was beautiful to watch.
The most beautiful knife in a kitchen ever! I'm so impressed and wish I hade your skills 🤗👌
In the beginning of this vid , I doubted your methods . You have schooled me ! Not exaggerating , a work of Art .
I guess everything in this guy’s home is 100% new
For real this youtuber can fix and clean anything
I love seeing tool restorations of all types, but older chefs knives in particular and this was a delight to watch with the materials involved. An amazing finish, better than the original by a mile, a delight to watch. Can I ask what type of wood you used.
Beautiful job! I don’t have power tools but did manage to restore an old axe head using vinegar, steel wool, sandpaper, metal files, sharpening stones, time, and effort. After fitting the head on a new hickory axe handle from Costco it looks and works nicely. It’s a simple thing I know, but very satisfying to see “trash” become like new again.
Beautiful! Although my heart stops when you touch the blade with your fingers! I have samurais
I know this comment is 8 months old, but I have to ask what you meant by "I have samurais".
Why did people disliked the video? Even if he did something you didn't like, he yet did a great work. It wouldn't be better if you supported him with a comentary telling what he can improve?
restore my relationship with my parents please
All you need is epoxy and a belt sander!😁
I find these videos oddly relaxing.
When I saw the reflection in the knife, I was like “DAMN!!” Lol I’ve never seen that done before. Just wanna say. Great work man!
You have made that blade look beautiful again
Needs a gold or brass ring of some sort between the blade and epoxy to make it look complete
Bringing the dead back to life. Keep up the great work 👌
Epic bro. The handle idea was just fantastic and the end product was classic!
Regardless what everyone else here says, I love the work and would be proud to have that knife in my kitchen.❤️❤️🙏
70/100
Nice restoration, though I'm not a fan of the resin part. I feel like it would have been better to do it the way it was done originally. But it does show creativity. So how about making a knife and/or forging one yourself rather than just restoration? I think that would make an interesting video.
Love the faux ice effect. If I had that knife, I would definitely put it on display.
Wow...👍 any of Japan’s products are of high quality 🇺🇸🇯🇵😁👍
This man has studied and crafted the blade
A+ on the handle creativity!
The restoration of the blade was very well done.
Very interesting technique and quite appealing results.
"I like the restoration but blah blah the handle... I would have done this instead...."
Oh ok, so where's the video of you beautifully restoring something? LOL!
Great job, diy cool stuff!
Yeah ... that's not how it works. If you go to a restaurant and they serve you a terrible pizza you can easily tell it's terrible, you don't need to know how to bake it to express your opinion about it. If something is bad is bad regardless of the fact that you can do it or not. In my opinion he did an awesome job, I just used an example to get my point across
what was the reason for them to do it? give me the same reason and i will, constructive criticism is always a good thing when not pushed, they still have the knife, they could relatively easily do that, it's just a bit of a waste since it's so good already, depends how much of a perfectionist they are and how well they like the knife, i can't do much of this, that is, i have no experience with it, now i could give it a shot if enough people wanted to see, but for a knife that will be used 3 times then rust, i don't see much point, you can't really sell things around here, so it would be a beautiful thing that would go to waste, and that's even if i bought all the tools (i kinda need them for other things anyways, so it's not that big of a deal, just money, money i don't have, otherwise i would have boughten the tools already, and i would need to know the amount of blue they used, or i would need to make a different colour, maybe a red or yellow one like fire or something? ice is far more believable and realistic and nice of course, and to get the ice like colour, i would need to get a blue whatever that stuff is and try a few times till i got the right colour, that's if i got the right blue even, i wonder how much of the resin i would need to use for testing? i wonder how much comes for $30, see why it would be much harder and not really reasonable for others to do it? youtube recommended this video, but i'm sure mine have never been recommended, even if i did the same thing
You do beautiful work, sir. It was a privilege to watch this happen.
Keep up the amazing work
Thanks dashawn!
Returning to the Japanese knife its lost dignity, a beautiful work with a rich imagination
Perfect restoration work! I am amazed! Also very nice handle design!👍🏻
Insanely pretty. What an artist!
That was an amazing restoration!!
Thank you Frank
Turned out beautiful. Well done.
I admire and respect the restoration, however I prefer the traditional look. I’m also not a fan of a gloss finish on wa handles. But it’s pretty cool. For anyone questioning the handle depth, Japanese knives with wa handles usually expose a large part of the tang creating a larger Choil. This benefits the pinch grip most (including myself🙂) chefs prefer for comfort on these blades. For me the position is on point.
Rory Shannon this knife didn’t come with the tang hanging out so far to start with so what you said means nothing at all it’s hog wash !!! 😝🤪🙄🙄🙄
That handle is so cool
Love the look of the handle but could be just me but the handle needed to be closer to the blade but great job
I don't know y I find these videos super satisfing
The mark may be "本種" Hon-Tane.
And Tanegashima Island is traditionally known as the site of the introduction of European firearms to Japan in 1542. So, Craftsmen in the island have kept alive traditional techniques for forging and sharpening iron tools.
Thanks a lot for this info :)
Is this knife available to purchase?
Entusiasta y poco hábil el muchacho. Casi destroza el cuchillo.
si. ha "tuneado" el cuchillo. No parece el mismo.
Amazing
If you ever sell this knife, please let me know straight away. It's beautiful and i'd love to own it!
Beautiful. Looks like a whole lot of fun.
Amazing job, but i agree with a lot of people in here. The blade should have been closer to the handle. It looks a little weird
Its not a western chef knife, people used to western handles find all japanese 3/4 tang knives look weird, at first.
I agree, a little more epoxy would have done the trick
Yeah, it looks like the blade is slipping out of the handle
Its supposed to look like that
He purposely left a wide gap between the handle and blade
Well done! The transition was wonderful.
Whoa I’ve never actually seen that chemical reaction happen before... only vaguely ever heard of it. That was fascinating
Wow what a beautiful restoration!
STUNNING!!! Can you do more of these Japanese style knives please? Thank you!
Looks fantastic, great idea with the resin.
everything is well done. The only problem is that this resin is not approved for food contact.
You must not have noticed, but he covered it with some type of varnish that i believe is food safe.
@@rebecks55 anyway this varnish won't last long if he uses the knife every day. He'll have to cover it over and over.
Valid point, though i don't see this being used as an everyday utensil. Maybe just as a pretty addition to a shelf.
Максим Попов don’t use the handle to cut your food
Very nice. Impressive! 👍👍👍
The work of restoration of the knife was magnificent, however, I do not know why the handle of the knife did not convince me
I love this videos! ❤
At 3:56, when you showed the results of vinegar being re-used, you should have added the voice-clip “IMPRESSIVE” from mortal kombat.
Toasty....
Amazing content. Thanks for sharing and explaining your errors and trial. I learned so much just from watching your videos. I’m always curious about how products are made. For you to show your crafty skills restoring it, gives me much knowledge. I am entertained. Keep up the great work, thanks again for sharing. You are awesome.
Love your restoration projects. Was cringing a bit while watching you sharpen the blade though . Japanese knives should be sharpened on special Japanese whetstone of progressively finer grit. These stones are kept soaked in water.
Turned out great! So many beautiful things can be done with epoxy resin.
You should check out MC-51 for rust. A lot of other restorers swear by it.
Gorgeous!