Thank you for that very clear and helpful video.. your disassembly instructions helped me clear out a stuck burr! That solves one problem. The handpiece I have seems to be running fine now. But I have another problem with the control unit also. The motor runs only at one speed oh, and I don't know what that is. The control knob does not change speeds at all. Have you had a problem similar to that? How do I get my speed control back? Have you ever had a problem with the control box itself and do you have any experience with fixing the speed control? Any suggestions from you will be very helpful, thank you again.
I have had this problem on Marathon 3. It's a transistor failure inside the control box, caused by an input voltage problem. Replace the transistor should be resolve it.
Thank you, very helpful video. When I pulled out the rotor from casing, the shims stuck on magnets. I am not able to determine the correct position of them. The only exploded view I have seen so far, is the one you have it. Can you upload it somewhere, since the link in the description is broken. Thanks.
junk handpiece. i know the owner of the company that makes these.. my father was in this business for over 45 years .. need parts i have some still left from my dads old repair company.. nsk so much better
Great video Ed. I'd love to see one where you change the bearings.
Thank you for that very clear and helpful video.. your disassembly instructions helped me clear out a stuck burr! That solves one problem. The handpiece I have seems to be running fine now. But I have another problem with the control unit also. The motor runs only at one speed oh, and I don't know what that is. The control knob does not change speeds at all. Have you had a problem similar to that? How do I get my speed control back? Have you ever had a problem with the control box itself and do you have any experience with fixing the speed control? Any suggestions from you will be very helpful, thank you again.
I have had this problem on Marathon 3. It's a transistor failure inside the control box, caused by an input voltage problem. Replace the transistor should be resolve it.
@@jaimefilho4959 Thank you for your response...
Thank you, very helpful video. When I pulled out the rotor from casing, the shims stuck on magnets. I am not able to determine the correct position of them. The only exploded view I have seen so far, is the one you have it. Can you upload it somewhere, since the link in the description is broken. Thanks.
Where could I find a COLLET CHUCK or Wrench to remove the collet? I can't find it at Patterson or Rams website.
سلام ممكن شرح اسباب عطل البيرنجات حق ميكرومتور ماراوثون
Ed, nice instructional video. Very helpful. Where did you get the parts list? Thanks
Where can I find the diagram of the hand piece parts list ??
Thank you so much for your instructions !!
You're welcome
Saeshin strong 90n micromotor is very similar. Thanks, this helped me a lot.
My engine burned I think.... Van In fix it?
HEllo Ed, How to you remove & replace bearings on both sides armature?
thank you sir
i repair my saeshin micromotor with your demonstration and advice
I'm Glad it helped.
❤️ from India
Can anybody ad a link to that parts diagram the link here is in Estonian ....and been able to find the right link.
Hello sir please what us reason heating problem
would you like to send me the exploded marathon schemac 35 000 rpm so i can order the different parts by reference.thanks
Olá vc saberia me dizer estou com uma caixa de controle da caneta ela só funciona em alta
Common spare parts are listed on www.ramprodinc.com website and available to order as well as all parts needed
For anyone, once you have taken the unit apart, changing the bearings is simple. just slide the old one off and the new one on.
I don't know how to take the c clip off.
I'm looking for portable micromotor with lethinium battery
Thanks, glad you like it.
hello, did you have diagram of voltage regulator?
Grzegorz Fiuczek no. Sorry I do not have wiring diagram
I am jawed from karachi Pakistan I am fully repairing and 50`000 rpm waindar call 0093142176669
Can you share where you purchased the bearings. Ram says they won't sell them. They said to sent them the hand piece.
I bought mine from Ram Products. I don't understand why they would not sell to you.
you can buy them at ldental.com too.
Thanks Dave, good info.
Hi Ed. I distribute Ram Products in Canada. If people are interested in parts or new equipment in Canada they can call 1-800-667-3770.
Muchas gracias muy útil
qué es lo primero que saca?
front armature bearing won't come off any suggestions?
Penetrating oil?
junk handpiece. i know the owner of the company that makes these.. my father was in this business for over 45 years .. need parts i have some still left from my dads old repair company.. nsk so much better
zzzzzzz.......zzzzzzz
Buen video de hecho pero muy lento 😅