*Bought this fan for the summer and so far it works great **Fastly.Cool** ! It's very quiet and not too loud, but also acts as a "white noise" when I go to sleep. No complaints from me!*
I have an industrial fan that cost a lot of money, so, I set myself to fix it, and it took me very little time instead of buying another one looking at your example, thank you Kluangman, it was fun.
We love this - its small and ruclips.net/user/postUgkxlmCcACUKg6nJKF53Fy9qNgPlHio1azE1 light so you can carry it around to another room with ease. My son can operate the switch super easy with the 3-speeds. And the openings around the fan are not wide enough for tiny fingers which is perfect if you have young ones in the house . We would definitely purchase this again.
I have a tip for you guys as to how to fix the thermal fuse. Don't snip it off since it's already an open circuit and will do no harm. Buy a whole bunch of spare thermal fuses from Ali Express (in case you have other devices and you fix funs for a living) and just solder two long wires to the two terminals of the blown fuse. Then attach the thermal fuse to the other ends of these wires without applying heat crimping is preferred. Wrap fuse in Kapton tape or insert in silicon heat resistant tube and attach it near the coils It does not have to be at the same original place as long as it can sense the heat from the coils.
artwdeetoo: Did the fan shop spinning because of the thermal fuse "shorted" and the fan blade is tight to turn freely. Did you oil the bearing area. I use a 10 weight oil used in Hunter ceiling fans to lubricate this type of fan.
The removed small component is a thermal fuse. It protects the circuit from overheating. You can short circuit it during the trouble shooting, but you need to replace it if is faulty. You cannot just remove it, doing that you will remove the fire protection!
Omg THANK YOU for showing how to get the motor casing face plate detached from body, those little plastic tabs confounded me and I actually feel kinda dumb for not figuring it out but now I’ve seen how easy it is I can go ahead and finish my repair without breaking the plastic bits.
You will find out that this is a fix on most any motor. They all have this thermal fuse in the windings. You can buy these thermal fuses at an Appliance store near you. You could just solder the two wires together but you won't have any protection if a short happens in the future, so it is best to buy the fuse and do it the right way!
Thank you so much, but you didn't say what was that small transistor type component which was blown off and for what purpose it was provided,now you removed it are two wires with coil wires shortened. Will it be good without that small component.
The component remove is the thermal fuse. It will run but if it overheats that safety will not be there. The fan could OVERHEAT... and it could start a FIRE. The fact that the fuse was blown means the fan has likely overheated before. You should find out why the fuse was blown and fix that first. Better to replace the fuse than to short it. (Sorting it is reasonable for troubleshooting if that is the problem but not a permanent solution.)
Hi ,I had a Tower fan that stop working completely ,you plugged and turn it on nothing ,what do you think my be the probably causes ? I will appreciate your help .thanks .
Without turning on the power supply ... The fan spin freely.and alignment the bush is ok .. iam already gently knocking the shaft ... Add some oil also the bush at both sides but steel same thing . so many thanks for very fast reply
when you turning on the speed selector ... did the fan response or or not ? if no response at all ... check the power cable .... check for broken power supply cable
Klungman: You repaired the fan less the safety feature in the motor. It can cause a fire. If it did not, and the fan stopped working, you would have burnt out the motor. The way you fixed it, you could have same the time and effort of removing the "thermal fuse" (the small flat square 130 degrees celcius). You could have just kept the two wires twisted together (when you tested the circuit with your meter. Just twisting the rwo wires together (soldering it) then wrap insulation over it. Final step, tie down all the wires down with zip ties (cutting it close with a nail clipper would rid the cit ends being sharp. When I remove the Thermo cut off (fuse), I replace it with an NTE8103 that has a rating of only 103 degrees celcius. Thus making the fan safer to use.
ihave found most 18 fans run hot due to high capacitor uf..for ex 2.5 uf if you replace it with a 2.0 uf the fan runs very well does not overspeed or heatup…
hey, as a youtuber i think.. it would be great & good investment for you to buy a gopro camera.. cuz every successful youtuber does, so why not, right? it's good for recording your content by getting a good angle/view by using the head strap, you'll save a lot of time instead of you take a while to find your camera/phone to record by your hand ✌🏻
Bro. Same one SONA standing remote type fan yesterday i connect wire, but why opposite direction running. What problem. Total 5 wire. Please srnd video bro. Thanks
You connect to the wrong running coil .. . Basically ... 3 speed coil have 4 coil and one coil are for starting running ... Choose the most low resistance to the capacitor ..
saniza69 sani ok ok ... Pilih kat omh ... Yg kalau Kita cantumkan kepala meter tu berbunyi teet2 ... Test kat kepala plug ... Antara life dgn neutral ... Tekan speed selector ... Meter tu mesti Ada bacaan dlm 300 omh ke atas lain speed lain bacaannya ... Kalau tak Ada bacaan bermakna dah open circuit ... Fius dah blow ... Macam dlm video tu ... Kalau bacaan Ada tapi kipas tak pusing ... Shaft kipas tu dah jem ... Guna WD 40
saniza69 sani grinder ni jarang coil dia rosak .. biasanya yg rosak carbon brush dia ... Ataupun wire ada putus dalam .. pasal kita tarik sana tarik sini ...
wall fan or table fan or stand fan for home use, usually have a same type of motor and these type of motor only use copper or stainless steel bushes as a bearing and almost all of these fans had a same shaft diameter.. and with some creativity .. you can mix almost all parts but do remember, be extra careful
My fan blades were obstructed from spinning for a period of time while I was out and the room, and now the fan doesn't work in the slightest. Will this video help with this, or is there another video I could watch? Is there any hope for my fan?
Try to spin the fan by hand and if it's spin freely .. yes this video can't help, but if the fan kind of heavy to spin, there are another video visit ruclips.net/video/Jow6QN93DXI/видео.html and also visit Table fan malfunction, diagnosis and repair ruclips.net/video/_b_1Em0dpZs/видео.html but if you saw that the coil were already burnt , there is no way you can repair it's
Hey! I got a problem with my fan. It slowly started to stop functioning. Like it's "battery" was draining and then it completely stopped and won't go on anymore. Any suggestion of what it could be? I have opened it and checked for wire damages and if there's something preventing it to spin. Thanks.
Sir i real appreciate your doings! Good job. However, i need help, I tried to do as you did, but my fan didn't rotate, but it only produce some kind of vibration/sound. Help me sir
Our kdk fan is new but only problem is that it has moving pin or tool which we pull up or down it makes a lot of noise n fan stops moving around. The fan is in working condition but while moving it has problem with that stick or tool so what should we do ? What is the name for that tool whihc we pull up n down for moving the fan can u pl. Tell me also? Can anyone tell me the solution and the name of the tool ?
Viewed from mobile devices ? Try to repair your own or friends table fan at home which only cost a few dollar... Circuit Protector Temperature Thermal Fuse goo.gl/GbZW9r Soldering iron kit goo.gl/kUS1J0 Multimeter goo.gl/KcBv65 CANADA amzn.to/2KauCxW UK amzn.to/2lnrcdm FRANCE amzn.to/2MElRdM
My fan was working just fine but I took it apart to clean the blades then it stopped working. I thought water got into the motor so I used a hair dryer to dry it out. It still does not work. A little fuse I can change but I cannot do any complicated even after watching your video
The shaft of rotor freely rotates when plugged off. But as electricity is connected, it tightens and make a sound(i.e. sound of not being able to rotate). Do you have any idea about the problem? Please share if any. And thanks for your video.
I did not see you replace the thermal fuse..i am not half as good as you i cant even use a circuit tester properly but i always replace the thermal fuse as it is important in preventing a fire in the motor.
Frank Fam try to check the power cord from speed selector to power plug and check your incoming power socket looking for broken wire and lastly insert the power plug, turn on and measure incoming voltage from before the speed selector between L and N and you must have a reading 230V or 110V depending which were used in your country ...
Hello Cooleck, Question i, got a fan that needs a capacitor 3.0uf, 250v what am getting at this point in time, is a 3.0uf 450v, would the 450v work. thanks
Boss my shaft got stuck due to the liquid that is coming out of the motor. It's working but very hard to rotate. Turning very slow and tight. What to do.PLEASE HELP ME
you're welcome and thanks for your visit and do remember , this problem will always there and you have to oil it's regularly and do remember to turn off your fan when leaving your house...have a nice day
SevenDeMagnus with higher capacitor .. the speed will increase ... and same with the temperature ... If the original was 1.7 ... 2.0 to 3.0... Still safe ... Higher than that ... no .. I won't recommend higher than 3.5.. if you fan blade were made from plastic ... It dengerous .. over speed ..
Hello im in real trouble. I open the case and removed the ossilator knob now when i fix it back fan works but it wont rotate sideways also that rough feeling in the knob is gone. Theres is a metal knob and a spring in side the ball fell down when i removed not sure whether i fixed it back correctly help please i can email you photos.
Kluangman Cooleck i only have one ball bearing and a spring might the other have fallen off thanks for the help is there anything i can do. Email me ranulpasan@gmail.com
Mera Usha Maxx air fan hai switch on Karne .nhi chalta hai haanth se ghumane see chalta hai Maine kepasiter air bhusing v chenage koi phaida nhi btaiye Kya karen
Our kdk fan is new but only problem is that it has moving pin or tool which we pull up or down it makes a lot of noise n fan stops moving around. The fan is in working condition but while moving it has problem with that stick or tool so what should we do ? What is the name for that tool whihc we pull up n down for moving the fan can u pl. Tell me also?
Many people get satisfaction from fixing things. That's worth a lot. Also, if you have any consideration for the environment then think about how many of these small appliances accumulate in the trash dump because nobody cared to fix it.
سلام عليكم لدي سؤال تقني هناك عطل غريب أصاب المروحة وهو عند التشغيل لابد من ضغط على زرين مع بعض لتشتغل ، مثلا زر رقم 1مع زر رقم 2 ،رغم أنني أصلحت المحرك وقمت بتنظيفه وتزييته هل هناك خطورة إذا اشتغلت بهذة طريقة ، اي نصيحة وشكرا.
Your speed selector not working... Something broken... Or poor condition of the contract point ... Dismantle the speed selector ... And check for broken components..
I mean everything else is pretty much solid state with magnets an coils. So there are a few electronic components and switches / buttons. Its nuts what we throw away, seriously.
Pwede bang gamitin ang shrinkable tube sa mga wires na nakadikit sa winding ng electric fan motor? Worried lang kase aq baka matunaw sa init at masira ang motor.
It's pretty hard to overheat an induction motor in the first place, so it makes me wonder what tripped the thermal. These motors need regular oiling. They run cool and quiet when oiled and they don't oil them enough when new, in my opinion. This seems to be the best protection from overheating.
i have orint table fan before capsitor 2.0 mfd i am change capasitor 2.0 mfd, 2.5mfd 3.15 mfd and bush, saft, but if i am push my hand so he runging else jam and ghum ghum please help me for repaire so many thanks
Without turning on the power supply ... The fan must spin freely when you spin it by hand ... try to alignment the bush ... By gently knocking the shaft ... Add some oil on the bush at both sides
this fan has no a/c defect, the armature is observed to be dead accurate and it may spin for one minute then stops and only hums. could the capacitor be at fault?
@@renfordwesleyjackson7817 check condition of fan ... Try to spin it's by hand .. rotation must be free without any type of heavy spin such as dry bushes or bearing ... Replace the capacitor
Thank you for making this 'tutorial'?Informative, and nicely done troubleshooting. And the soundtrack is freaking interesting! You're not from around here, are you? Lol, I knew it! Thanks again.
tok ai kipas model baru sahaja yg Ada thermal fuse ... Kipas lama tak ada... Kalau bilah kipas tu boleh pusing dgn tangan Dan tak ketat ... Cuba tukar kotak Hitam Empat segi tu ... capacitor
sir ji mera 1 stand fan he,woh gumta toh he lekin pehele hath se hillana parta he.aur sirji speed 123 nahi sirf slow gumta he baton kam nahi karta plz bataye
if the fan blade spin freely when you spin it by hand ... that mean,you have to replace the capacitor ... but if the fan blade were quit heavy or some kind of tight when you trying to spin it by hand ... follow the step which shown in the video
Bang, saya nak tukar kapasitor kipas. Macam mana nak discharge dia? Saya trauma sikit bab2 kapasitor ni. Dah la sekarang musim panas, kipas plak lembap... T.T
Tak perlu risau .. bila Kita off power ...kapasitor tu akan discas sendiri ... Dlm berapa saat ... atau cabut plug Dan shortkan L dgn N guna skru driver
sir i'm not so clear the part that you repair on the cable at the motor winding wire coil? can you more detail explain at that part? thank you for this video sharing.
*Bought this fan for the summer and so far it works great **Fastly.Cool** ! It's very quiet and not too loud, but also acts as a "white noise" when I go to sleep. No complaints from me!*
Bots
Nimma vedio nodi namma mane stand fan reperi madidenne adu ega channagi agide tumba tq
I have an industrial fan that cost a lot of money, so, I set myself to fix it, and it took me very little time instead of buying another one looking at your example, thank you Kluangman, it was fun.
Congratulations to you artwdeetoo .. I'm speechless ... When someone able to repair their own ... and thanks artwdeetoo for your visit 😀👌
Tq v much for this, I did exactly what you showed in this video and found the thermal fuse was the problem. The rating is 130°C 1A at 250V.
We love this - its small and ruclips.net/user/postUgkxlmCcACUKg6nJKF53Fy9qNgPlHio1azE1 light so you can carry it around to another room with ease. My son can operate the switch super easy with the 3-speeds. And the openings around the fan are not wide enough for tiny fingers which is perfect if you have young ones in the house . We would definitely purchase this again.
I have a tip for you guys as to how to fix the thermal fuse. Don't snip it off since it's already an open circuit and will do no harm. Buy a whole bunch of spare thermal fuses from Ali Express (in case you have other devices and you fix funs for a living) and just solder two long wires to the two terminals of the blown fuse. Then attach the thermal fuse to the other ends of these wires without applying heat crimping is preferred. Wrap fuse in Kapton tape or insert in silicon heat resistant tube and attach it near the coils It does not have to be at the same original place as long as it can sense the heat from the coils.
artwdeetoo: Did the fan shop spinning because of the thermal fuse "shorted" and the fan blade is tight to turn freely. Did you oil the bearing area. I use a 10 weight oil used in Hunter ceiling fans
to lubricate this type of fan.
The removed small component is a thermal fuse. It protects the circuit from overheating. You can short circuit it during the trouble shooting, but you need to replace it if is faulty. You cannot just remove it, doing that you will remove the fire protection!
And lets not forget: it was already blown, so the motor HAS overheated before 😱!
Powerful..u r very skillful thank for sharing..God blessed your skillful brains and hands all the time...I have learned alot .. 🙏💯🌹💖📌📍🛠🔧🛠⚒
Thanks for sharing your knowledge with us, i solved my problem
really really good video....you save my time and money for repair my fan...thank you...keep it up...
Glad to hear that
Thanks bro, I was worry for this problem, neway god bless you always and give u the bless for putting more this type of suggestions.
Always welcome
l76v6b67vxmp7m77llb7pbvnb7m7vl6p6xlpuvl6x6vb6n6b6lmxv6l6l6bmnmbyvlhnl6lm6bnu66cjpbcl6m6pfm069blniov966mvxbnvlxnibbln7vnp6ddbdndnvb6x6blvp6b6vm6xlx66lxblybbvb66vdj67c666bbxbvmbv6xbvnmxp6lpmmbmbvxlccnbmnmcbnvm6vb6mblb6b6ml6xxbm6l6bvmbvm666nbvnvm6n6fl6p6nxcbpmbm6nmxvbnm6b6v6m66mnbn6c66v6lb7l6mbmb7ll7bi6nvl7n66m6lv6n6cvnb6mcublvmvohnu6l6mvyvmcgmnc6cb6bvn6bh6bb66mlnmv6bbvjkixn7vlpblmpllxbnplbvk676666bbl6mn6b6mby 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
l76v6b67vxmp7m77llb7pbvnb7m7vl6p6xlpuvl6x6vb6n6b6lmxv6l6l6bmnmbyvlhnl6lm6bnu66cjpbcl6m6pfm069blniov966mvxbnvlxnibbln7vnp6ddbdndnvb6x6blvp6b6vm6xlx66lxblybbvb66vdj67c666bbxbvmbv6xbvnmxp6lpmmbmbvxlccnbmnmcbnvm6vb6mblb6b6ml6xxbm6l6bvmbvm666nbvnvm6n6fl6p6nxcbpmbm6nmxvbnm6b6v6m66mnbn6c66v6lb7l6mbmb7ll7bi6nvl7n66m6lv6n6cvnb6mcublvmvohnu6l6mvyvmcgmnc6cb6bvn6bh6bb66mlnmv6bbvjkixn7vlpblmpllxbnplbvk676666bbl6mn6b6mby num6c6bvn6xnmv6nkgl6lgbp6bmm76u7nxvnbmbb7np7knllp6vnn6blhmn66b6nlb6c6bmvnmbxnbk6bc66m6pxl67vvp6xbcbpmlplbln6xv6nbbvb6mx6v6666m6mu6cm6mvbvl6bmb6lg6c66l666b7mvu7blhbxtbmc76txv6mbkvuyv7vynolbn6lbn6lbvlvyncj6xvmbvm66b6m6cm6lnmnnbnnbhmobl6nv6vxb6mv669bvnlb6bl6u6kpblp666lbncmv6b6xll6b666dcmmmxbcg66b6l6vvn6mbb6l66b6x66ml6ml66nxbn6bvmbnbbvmmv6nu6vynv6v6nnk7m6bxmxbxbfmvlbc6lbimb6mnnvxlnl6x66nd6pxv6v6m6bbvnbnvnmbv6mbvncnbmdm6vmbv6bbv66bnxbkmlxlm66bn7bv6lbgpvkpnlbx666mbv6mdtv6ybxh6mbx6vmlbbv6bc66b6nv66b66l6bb6v6nbvl6l6moxuclxf7bvmblvy777nlvn7bvkimgnxmn6pv6b6blibnl6v6vxbvbbm6vbvkbbmhvnnc66b7mbcbmvl7ovb7bpk7xpppkj6ylpb7vpjbpo77ylbomim7i7lv7nbmpvxm6nmvb6lxbmv666lb6b66n6666nmbpkp6bmvm6bnl6kp7bvbm7b76mnbvmnubj66nvnmlvmbcx66bbbvmbmvnbnn0vobx6lbvbx6vmvm6x6vb6cl6v6l6mpv6lbyndbcvn6vnvmmbmxbmvcm
@@KluangmanCooleck tuan kluang, johor ker
Omg THANK YOU for showing how to get the motor casing face plate detached from body, those little plastic tabs confounded me and I actually feel kinda dumb for not figuring it out but now I’ve seen how easy it is I can go ahead and finish my repair without breaking the plastic bits.
You will find out that this is a fix on most any motor. They all have this thermal fuse in the windings. You can buy these thermal fuses at an Appliance store near you. You could just solder the two wires together but you won't have any protection if a short happens in the future, so it is best to buy the fuse and do it the right way!
Even Motor is not jame but when give current it struck what should b the problem capicter or something else
Thank you so much, but you didn't say what was that small transistor type component which was blown off and for what purpose it was provided,now you removed it are two wires with coil wires shortened. Will it be good without that small component.
The component remove is the thermal fuse. It will run but if it overheats that safety will not be there. The fan could OVERHEAT... and it could start a FIRE. The fact that the fuse was blown means the fan has likely overheated before. You should find out why the fuse was blown and fix that first. Better to replace the fuse than to short it. (Sorting it is reasonable for troubleshooting if that is the problem but not a permanent solution.)
Hi ,I had a Tower fan that stop working completely ,you plugged and turn it on nothing ,what do you think my be the probably causes ? I will appreciate your help .thanks .
So why did the motor get hot enough to trip the thermal element?
Tq v mach ye vidio dekhaneki bat hamara fan chalu hogeiya pahele kharap tha
this will be useful for when the old maison pedisulfan in my room
breaks
Without turning on the power supply ... The fan spin freely.and alignment the bush is ok .. iam already gently knocking the shaft ... Add some oil also the bush at both sides but steel same thing . so many thanks for very fast reply
when you turning on the speed selector ... did the fan response or or not ? if no response at all ... check the power cable .... check for broken power supply cable
Check (L) and (N) wire from power plug to speed selector
You did a great job, but that was so involved for me. It felt complicated. I need a whole semester to learn this. ;)
Slowly slowly. When you repeat this for another 6 semester you will get your diploma.
Wan Khairul anuar
LOL!!!
terima kasih bang, semoga panjang umur murah rezeki, amin
Klungman: You repaired the fan less the safety feature in the motor. It can cause a fire. If it did not, and the fan stopped working, you would have burnt out the motor.
The way you fixed it, you could have same the time and effort of removing the "thermal fuse" (the small flat square 130 degrees celcius). You could have just kept the two wires twisted together (when you tested the circuit with your meter.
Just twisting the rwo wires together (soldering it) then wrap insulation over it. Final step, tie down all the wires down with zip ties (cutting it close with a nail clipper would rid the cit ends being sharp.
When I remove the Thermo cut off (fuse), I replace it with an NTE8103 that has a rating of only 103 degrees celcius. Thus making the fan safer to use.
All connected, but switch on ready revise running the fan how. What wire need to change.
ihave found most 18 fans run hot due to high capacitor uf..for ex 2.5 uf if you replace it with a 2.0 uf the fan runs very well does not overspeed or heatup…
What is the name of this Havells head whant to replace his head
appreciated informative vids thanks sir, 👍 ...now i have a question sir, how does the fan works?, is it still working til now..??
hey, as a youtuber i think.. it would be great & good investment for you to buy a gopro camera.. cuz every successful youtuber does, so why not, right? it's good for recording your content by getting a good angle/view by using the head strap, you'll save a lot of time instead of you take a while to find your camera/phone to record by your hand ✌🏻
Bro. Same one SONA standing remote type fan yesterday i connect wire, but why opposite direction running. What problem. Total 5 wire. Please srnd video bro. Thanks
You connect to the wrong running coil .. . Basically ... 3 speed coil have 4 coil and one coil are for starting running ... Choose the most low resistance to the capacitor ..
Kluangman Cooleck next week i will check. Thanks.
Bhai mere pass yek pankha hai bich se puri tar alag alag hai kaise pata kare ki pavar ki aur battan ki kaon si hai please bataye yek yek wayer ko
Fan with three speed have four coil ... One coil for start running direction ....
And capacitor attached to these coil...
Other coil are for speed ...
@@KluangmanCooleck 6 wayer red black yellow bullu
Whait .dark red bullu
Jaha par pavar conecsun hota hai vahi pe 6 wayar aaya hai upar se aur koi part nahi hai sab fek diya koi
@@shyamooamni9257 usually the black wire are N and red, yellow and blue are for speed selector
terima kasih berkongsi ilmu.. kat rumah banyak kipas rosak.. kalau nak cek coil mcamna..
saniza69 sani you must have a multimeter ...
Kluangman Cooleck .. ada..
saniza69 sani ok ok ... Pilih kat omh ... Yg kalau Kita cantumkan kepala meter tu berbunyi teet2 ... Test kat kepala plug ... Antara life dgn neutral ... Tekan speed selector ... Meter tu mesti Ada bacaan dlm 300 omh ke atas lain speed lain bacaannya ...
Kalau tak Ada bacaan bermakna dah open circuit ... Fius dah blow ... Macam dlm video tu ...
Kalau bacaan Ada tapi kipas tak pusing ... Shaft kipas tu dah jem ... Guna WD 40
ok.. tq bro.. dh repair 2 kipas.. ada 3 lagi.. tq.. kalau nak cek wiring angle grinder camna. blh ajo..
saniza69 sani grinder ni jarang coil dia rosak .. biasanya yg rosak carbon brush dia ... Ataupun wire ada putus dalam .. pasal kita tarik sana tarik sini ...
Hi sir that fuse remove after no coming any problam that fuse must need or no need
if you are in doubt to bypass the thermal fuse, you can replace it's with new fuse.
Circuit Protector Temperature Thermal Fuse goo.gl/GbZW9r
Bush aur shaft kse bdle ghr pe wall fan ke ye bta dijiye
wall fan or table fan or stand fan for home use, usually have a same type of motor and these type of motor only use copper or stainless steel bushes as a bearing and almost all of these fans had a same shaft diameter.. and with some creativity .. you can mix almost all parts but do remember, be extra careful
Good video going to repair my fan with help of this video 👍
Good luck!
My fan blades were obstructed from spinning for a period of time while I was out and the room, and now the fan doesn't work in the slightest. Will this video help with this, or is there another video I could watch? Is there any hope for my fan?
Try to spin the fan by hand and if it's spin freely .. yes this video can't help, but if the fan kind of heavy to spin, there are another video visit ruclips.net/video/Jow6QN93DXI/видео.html
and also visit Table fan malfunction, diagnosis and repair ruclips.net/video/_b_1Em0dpZs/видео.html
but if you saw that the coil were already burnt , there is no way you can repair it's
Terima kasih bos . Saya bangga jadi anak Malaysia .hahahahah
Hey! I got a problem with my fan. It slowly started to stop functioning. Like it's "battery" was draining and then it completely stopped and won't go on anymore. Any suggestion of what it could be? I have opened it and checked for wire damages and if there's something preventing it to spin. Thanks.
Grease the bearings
change capacitor with the same value
Sir i real appreciate your doings! Good job.
However, i need help, I tried to do as you did, but my fan didn't rotate, but it only produce some kind of vibration/sound. Help me sir
Did the shaft spin freely?
@@KluangmanCooleck no it didn't, but it provides some kind of noisy
Just put some oil or WD40
Suggestions from Kim can be apply .. 👍
@@KluangmanCooleck it didn't. And if i manually try to rotate when switched on still it didn't. But when switched off it did. Help...!
Our kdk fan is new but only problem is that it has moving pin or tool which we pull up or down it makes a lot of noise n fan stops moving around. The fan is in working condition but while moving it has problem with that stick or tool so what should we do ?
What is the name for that tool whihc we pull up n down for moving the fan can u pl. Tell me also? Can anyone tell me the solution and the name of the tool ?
If the fan were still under warranty ... Sent it back to the shop which you bought it from ... Something broken or mulfunction..
Bang, kalau dawai tembaga halus tu byk yg putus, agak2 blh pkai lg x? Masa nk bukak shaft dia tu terkena dawai tu.. byk jugak putusss..
kalau banyak yg putus tak payah teruskan repair
@@KluangmanCooleck maksudnya terus tukar motor sketul ye bang?
Viewed from mobile devices ? Try to repair your own or friends table fan at home which only cost a few dollar...
Circuit Protector Temperature Thermal Fuse goo.gl/GbZW9r
Soldering iron kit goo.gl/kUS1J0
Multimeter goo.gl/KcBv65
CANADA amzn.to/2KauCxW
UK amzn.to/2lnrcdm
FRANCE amzn.to/2MElRdM
What's the thermal fuse rating, ? Tq .
My fan was working just fine but I took it apart to clean the blades then it stopped working. I thought water got into the motor so I used a hair dryer to dry it out. It still does not work. A little fuse I can change but I cannot do any complicated even after watching your video
you may have accidentally broken some wires... maybe
I appreciate your hard work since I did the same thing and I failed.
The shaft of rotor freely rotates when plugged off. But as electricity is connected, it tightens and make a sound(i.e. sound of not being able to rotate). Do you have any idea about the problem? Please share if any. And thanks for your video.
try to replace the fan capacitor and make sure its were the same rate
sujit dh same happened to me..i dont know what to do..
Muhammad Zakwan Azizi if the fan can spin freely, just replace the capacitor, a small black box with two wire
I did not see you replace the thermal fuse..i am not half as good as you i cant even use a circuit tester properly but i always replace the thermal fuse as it is important in preventing a fire in the motor.
Thanks a lot for your sharing.
My pleasure
Hi, I check the capacitor it seems to be good, I checked the coil it seems to be good too, what else might be bad?
Frank Fam try to check the power cord from speed selector to power plug and check your incoming power socket looking for broken wire and lastly insert the power plug, turn on and measure incoming voltage from before the speed selector between L and N and you must have a reading 230V or 110V depending which were used in your country ...
the coil might be shorted & need to be recoiled. check up the resistance of the coils
Check the thermal fuse to see if it is blown.
Power bro.. semoga murah rezeki
Are you in MotoGP...or F1 racing track side
😂
Hello Cooleck, Question i, got a fan that needs a capacitor 3.0uf, 250v what am getting at this point in time, is a 3.0uf 450v, would the 450v work. thanks
3uf capacitor 400/450v will suit 240v motor
and its will last longer then the 240v capacitor
bhaiya mere bhi hevells ka fan he kiski 3 no waali speed button dheeli ho gai he wo kaam nahi Kar rahi he keise theek katein
Boss my shaft got stuck due to the liquid that is coming out of the motor. It's working but very hard to rotate. Turning very slow and tight. What to do.PLEASE HELP ME
manidesh EPIC use wd40 or something similar to free the shaft
And then use a very light oil to lubricate the shaft such as sawing machine oil
Kluangman Cooleck thank you
you're welcome and thanks for your visit and do remember , this problem will always there and you have to oil it's regularly and do remember to turn off your fan when leaving your house...have a nice day
Hi. If you replace the capacitor to a higher, would that make the fan spin faster? Thank you. God bless, Proverbs 31
SevenDeMagnus Yes the fan will spin faster... But not too high
Thanks. Will a higher capacitor (maybe 3 to 5x higher) damage the motor?
SevenDeMagnus with higher capacitor .. the speed will increase ... and same with the temperature ... If the original was 1.7 ... 2.0 to 3.0... Still safe ... Higher than that ... no .. I won't recommend higher than 3.5.. if you fan blade were made from plastic ... It dengerous .. over speed ..
good and VERY CLEAR video. thanks for isolating each part of the circuit and for 😔 emphasising the safety aspect
বাই জালি বা টেবিল পেন ৩৭গেজ তার তাকে একানে কি ৩৪ গেজ তার ব্যাভহার করা জাবেনি আর রানিং বা স্টাটিং কত বেব্দান তাকে প্লিজ জানাবেন
Really your great 👌👌👍☺👍👍👍👍
Many many thanks
Hello im in real trouble. I open the case and removed the ossilator knob now when i fix it back fan works but it wont rotate sideways also that rough feeling in the knob is gone. Theres is a metal knob and a spring in side the ball fell down when i removed not sure whether i fixed it back correctly help please i can email you photos.
Ranul Pasan there's one bearing placed at each end of the hole and total of 2 bearings ... If you only putting one , it's wont work ...
Attached your email here and I will respond as soon as I can..😁
Kluangman Cooleck i only have one ball bearing and a spring might the other have fallen off thanks for the help is there anything i can do. Email me ranulpasan@gmail.com
Mera Usha Maxx air fan hai switch on Karne .nhi chalta hai haanth se ghumane see chalta hai Maine kepasiter air bhusing v chenage koi phaida nhi btaiye Kya karen
Usha mist air pedestal fan ex vat 400mm connection check karane ke videos banaeye sar
कहां से है
you must change the shaft and bushing coz it may work any longer ,that is the cause of blown off the fuse diode .
Our kdk fan is new but only problem is that it has moving pin or tool which we pull up or down it makes a lot of noise n fan stops moving around. The fan is in working condition but while moving it has problem with that stick or tool so what should we do ?
What is the name for that tool whihc we pull up n down for moving the fan can u pl. Tell me also?
@@Parinmahomedriaz4184 oscillation knob
U should do this quickly 😊
Thanks. You just convinced me to buy a new fan. My time is worth more than this!
Manolis Gledsodakis 😂😅
Manolis Gledsodakis 😂
Many people get satisfaction from fixing things. That's worth a lot. Also, if you have any consideration for the environment then think about how many of these small appliances accumulate in the trash dump because nobody cared to fix it.
Life is not only about money. This is a great way to learn electronics and get satisfaction from saving something from the dump.
Thanks very much cooleck, for all your answers that you gave me.Winston
سلام عليكم لدي سؤال تقني هناك عطل غريب أصاب المروحة وهو عند التشغيل لابد من ضغط على زرين مع بعض لتشتغل ، مثلا زر رقم 1مع زر رقم 2 ،رغم أنني أصلحت المحرك وقمت بتنظيفه وتزييته هل هناك خطورة إذا اشتغلت بهذة طريقة ، اي نصيحة وشكرا.
واليكم السلام
لا 1 تحقق من محدد السرعة الخاص بك
لا 2 لا بأس في إضافة بعض الزيت إلى العمود
وشكرا لزيارتك
السلام عليكم
@@KluangmanCooleck شكرا لك على ردك
Thanks man repaired my table fan
Does it still work? Did it lit on fire?
आपके नंबर भेजे
9925553618
first of all thanks to made this video..but i have some confusions ..where goes to two white wire..when cut off two white wire..plz reply me brother.
sir ye jo low medium high wire ye nikalte hai ,startting ki ya running ki hoti hai
Starting coil mai sai
Sir i check all 123 but the #3 is the only not functioning 1 and 2 is ok but 3 is not what cause of trouble?
Your speed selector not working... Something broken... Or poor condition of the contract point ... Dismantle the speed selector ... And check for broken components..
@@KluangmanCooleck thnx sir for quick response,
@@luzvimindabanaco8516 you're welcome 😀 and thanks for your visit
@@KluangmanCooleck i always watch your video, i have another question if you check all 123 is ok what is trouble?
same problem as the fan in this video, faulty thermal fuse OR...if getting some reading with multi-meter ... try to replace the fan capacitor
I usually just take off the thermal whatever and replace it with a wire crimper so i wouldnt have the situation of the fan stop working.
details, tq
I mean everything else is pretty much solid state with magnets an coils. So there are a few electronic components and switches / buttons. Its nuts what we throw away, seriously.
Thanks for the information.Man you are good .it's too technical for me..
Great video ..But those motorcycles in the background are driving me nuts !
Joe hahahaha 😂😂😂 thanks for your visit
Is that what that noise was? I couldn't figure out what it was. Sounded like some underwater sea monster. Drove me crazy too.
This fuse us really short and there is a white around that and a red line all around it.
Any response from u all
Thermal cut-out should be replaced ,its a safety issue!
Good job my friend india is awesome
Pwede bang gamitin ang shrinkable tube sa mga wires na nakadikit sa winding ng electric fan motor? Worried lang kase aq baka matunaw sa init at masira ang motor.
pwede
I don't like the idea of bypassing fuses but still thankyou for uploading the video
It's pretty hard to overheat an induction motor in the first place, so it makes me wonder what tripped the thermal. These motors need regular oiling. They run cool and quiet when oiled and they don't oil them enough when new, in my opinion. This seems to be the best protection from overheating.
Really nice video.
Sir aisa hi mere pass ek pankha hai jismai power dete hi wah jaam ho jaata hai kya kare please help me
The Fan stuck or slow please watch this video ruclips.net/video/Jow6QN93DXI/видео.html
good video
yeah have to be slow and no need speed the video so
we can watch the tutorial more clear
an easy to learn thankyou😍
i have orint table fan before capsitor 2.0 mfd i am change capasitor 2.0 mfd, 2.5mfd 3.15 mfd and bush, saft, but if i am push my hand so he runging else jam and ghum ghum please help me for repaire so many thanks
Without turning on the power supply ... The fan must spin freely when you spin it by hand ... try to alignment the bush ... By gently knocking the shaft ... Add some oil on the bush at both sides
when the bushing is ok and nothing is burnt what else can be the problem
@@renfordwesleyjackson7817 check for broken wire ... From main power supply to speed selector ...
this fan has no a/c defect, the armature is observed to be dead accurate and it may spin for one minute then stops and only hums. could the capacitor be at fault?
@@renfordwesleyjackson7817 check condition of fan ... Try to spin it's by hand .. rotation must be free without any type of heavy spin such as dry bushes or bearing ... Replace the capacitor
Chetta chettante youtubil 2videoye ullu
Thank you for making this 'tutorial'?Informative, and nicely done troubleshooting. And the soundtrack is freaking interesting! You're not from around here, are you? Lol, I knew it! Thanks again.
boss,kalau kipas tu rosak tapi memang dah takda thermal fuse maksudnye motor dia memang dah takleh pakai dah ke?terima kasih
tok ai kipas model baru sahaja yg Ada thermal fuse ... Kipas lama tak ada... Kalau bilah kipas tu boleh pusing dgn tangan Dan tak ketat ... Cuba tukar kotak Hitam Empat segi tu ... capacitor
dah tukar capasitor pon tak jalan,btw saya tak buat test pakai multimeter sbab takde,perlu ke nak cek multispeed tu?
tok ai perlu check Dari wire Speed selector ke plug ... Kekadang pasal wire putuspun tak boleh hidup ... Multimeter perlu utk buat kerja ni ..
والله هذه الفيديوهات جميله ولا فى الخيال
Very nice sir
sir ji mera 1 stand fan he,woh gumta toh he lekin pehele hath se hillana parta he.aur sirji speed 123 nahi sirf slow gumta he baton kam nahi karta plz bataye
if the fan blade spin freely when you spin it by hand ... that mean,you have to replace the capacitor ... but if the fan blade were quit heavy or some kind of tight when you trying to spin it by hand ... follow the step which shown in the video
So you removed the blown part
Nice 👍🏻👍🏻 🇮🇳 Kuki 22|04|2022
Bang, saya nak tukar kapasitor kipas. Macam mana nak discharge dia? Saya trauma sikit bab2 kapasitor ni. Dah la sekarang musim panas, kipas plak lembap... T.T
Tak perlu risau .. bila Kita off power ...kapasitor tu akan discas sendiri ... Dlm berapa saat ... atau cabut plug Dan shortkan L dgn N guna skru driver
@@KluangmanCooleck boleh tak kalau saya tukar kapasitor dari 1.0uf500v kepada 1.5uf340v ? Ada kesan apa2 tak? Bahaya tak?
@@wowwow8171 boleh ... Lagi besar Volt ... kapasitor tu lagi tahan lasak ... Bab uf ni kalau berbesa cuma 0.5 je ... Boleh
Kapasitor nipun ... Berbeza2 kebolehan dia jika ketebalannya berbeza ... Walaupun mempunyi uf yg sama
Fab ren -ren awaj karta ha but nhi ghumta hai kaise solve hoga pls help me sir
Pular stand fan me muving set karna h
very informative..
Glad you liked it
I removed the thermistor fuse but my fan is the same so slow and gets overheated so fast
dear friend you have no mouth to tolk it is very sad to give some ideas to your spectatures
6:38 what is the role of black screw one ?? Thanks :)
sir i'm not so clear the part that you repair on the cable at the motor winding wire coil? can you more detail explain at that part?
thank you for this video sharing.
that small part with two pole which I cut off were actually a small amp fuse which will blown off if the amp in the coil exceeding the fuse limit.
havells fan coil convetion bta bhai
Nurul Syafiqah Abd Rahim
sir fharata fan rotor kharab ka karad sound ati hai