*PINNED UPDATES* Some info taken from comments that people might find helpful... 1. The quick screws work with other fans that aren't from Coolermaster. But if you use an IXO like I do then all screws are faster screws. 2. The 140mm fans don't fit in the bottom of the 2500D version of this case. This is the airflow model with a mesh front and fan mounts. The 2000X has a thinner glass panel as shown here. 3. The fans look great becasue some of them are reverse blade. See here: ruclips.net/video/VV7E-Xqq8y0/видео.html Thanks!
For the 2500X, which has just a glass panel for the front, the three 140mm fans fit perfectly in the bottom... everything screws in as it should. Hope this helps.
It depends on the GPU, but the one in the video is the width of 2.5 rear slots and there's a gap between the top of the fans and the GPU cooler that you can fit your hand in. It's hand thickness... so you can get your fingers in there but you can't plug in a USB header unless you're good with long nose tweezers because there's not much wriggle room. Take a look at 33:57 as that's the best view this video has. You can see the GPU has a gap between the fans and the cooler on it. Note that the top of the fans is slightly lower than the bottom edge of the motherboard so that should give you a clue. The closer the card is to the bottom edge the closer it will be to the fans. This is a MATX case though. A full three slot card would fit because that doesn't overhand the bottom of the motherboard - but it wouldn't be a good idea - I would say a 2.5 rear slot width card is the limit.
Details about radiator fitting can be found here... www.corsair.com/uk/en/explorer/diy-builder/cases/corsair-2500-series/#p-data-block-keyxlvc1installing-a-radiatorp The motherboard actually mounts low in the case to give clearance above it. If the cooler you're thinking about has a typical thickness with standard thickness fans then it should be clear of the RAM modules.
*PINNED UPDATES*
Some info taken from comments that people might find helpful...
1. The quick screws work with other fans that aren't from Coolermaster. But if you use an IXO like I do then all screws are faster screws.
2. The 140mm fans don't fit in the bottom of the 2500D version of this case. This is the airflow model with a mesh front and fan mounts. The 2000X has a thinner glass panel as shown here.
3. The fans look great becasue some of them are reverse blade. See here: ruclips.net/video/VV7E-Xqq8y0/видео.html
Thanks!
I've used the quick screws on normal fans too without issue as well :)
Nice to know.
I use an Ixo so all screws are quick screws. 🤣
3:30 Now i no for what these cases are used for."dam it"Now i need to get rid of the others i have .LOL
i got the 2500D air flow and i bought lian li TL 140mm fans it doesnt fit on the bottom
Thanks for the info.
The 2500X has a glass panel - so thinner than a front that’s got mesh and fan mounts.
@@sterntechdaddy But does screw fit properly? I just didnt get that?
For the 2500X, which has just a glass panel for the front, the three 140mm fans fit perfectly in the bottom... everything screws in as it should.
Hope this helps.
Thanks for the video
What is the clearence for GPU left after installing 3x140 at the bottom?
It depends on the GPU, but the one in the video is the width of 2.5 rear slots and there's a gap between the top of the fans and the GPU cooler that you can fit your hand in.
It's hand thickness... so you can get your fingers in there but you can't plug in a USB header unless you're good with long nose tweezers because there's not much wriggle room.
Take a look at 33:57 as that's the best view this video has. You can see the GPU has a gap between the fans and the cooler on it.
Note that the top of the fans is slightly lower than the bottom edge of the motherboard so that should give you a clue. The closer the card is to the bottom edge the closer it will be to the fans. This is a MATX case though.
A full three slot card would fit because that doesn't overhand the bottom of the motherboard - but it wouldn't be a good idea - I would say a 2.5 rear slot width card is the limit.
How well would the liquid freezer 3 360 fit in the top with the "rgb bling" ram modules? And if it could fit the 280 version?
Details about radiator fitting can be found here...
www.corsair.com/uk/en/explorer/diy-builder/cases/corsair-2500-series/#p-data-block-keyxlvc1installing-a-radiatorp
The motherboard actually mounts low in the case to give clearance above it. If the cooler you're thinking about has a typical thickness with standard thickness fans then it should be clear of the RAM modules.
todos los coolers estan extrayendo aire, no hay flujo de aire en esa configuraciòn.
Alguns se os ventiladores forem de lâmina reversa... 😜
Você pode ver as caixas para eles às 23:50
🙂
@@sterntechdaddy nice !
See this: ruclips.net/video/VV7E-Xqq8y0/видео.html
Os ventiladores de lâmina reversa são brilhantes!