BASIC REPAIRS - iPHONE 7 NO SIM - NO IMEI - NO SIGNAL - QUALCOM BASEBAND - JUST SEARCHING

[@mjd9813]

What temp and air settings you used to remove the ic if you dont mind me asking?

[@tibornyari3232]

Hi! Why did I have to use a jumper? Which of the 4 solder points was not a ground point?

[@ipadmini2249]

thanks bro 100% working this method

[@jorge195501]

Thank you for another good video.

[@samuelhinidza9678]

Please where do you buy replacement chips

[@emanuelrodriguez2177]

Hola hermano , que estacion de calor utilizas ?

[@Fly_HiGh-wt8xd]

Thanks! Solved my baseband issue

[@nourdin9215]

كيفا ش شي والا لمنتخب كوررا لمنتخب كوررا منالأهداف سورة التوبة من صلاة الفجر صلاة التراويح ليلة ليلة القدر

[@ayoubaghsain9221]

Sometimes it didn’t work even if we make that jump i got no signal, i found a short on the caps around the BBPMU but when i remove the BBCPU the short goes is there a solution ?

[@sharfazhameed6382]

Great video Ben. Thx for your time and your detailed informations.

[@zahangirkhan3457]

Hi sir please tell me .how to remoov ic audio iphhone 7 and 7plus...Good tamprachar....

[@DAVIDDAVID-85]

I have an iPhone 7 Sharing and I don't have it, and when I removed the Essie Power Baseband Qualcomm, I found two dots attached to the Essie on the Qualcomm Essie, what happened, sir?

[@krzysztofbednarek9485]

Thank You , Good job , dobra robota .

[@romzget1892]

should I restore iphone after put new bbmpu(baseband ) Ic should I restore or update on itunes???

[@easytech23]

if your phone is in activation screen you need to restore..if your can access the menu no need..

[@smustafov8790]

My iphone 7 always shorts its with qualcomm chip. Must be grounded or it can be from any other thing ?

[@faizalichal9651]

i have same problem,brother.....can you helpme ? are you cange the ic or not....???
I have the same damage, and I get short on the capacitor, c5630, c5703, c5701, is the IC really broken? because I haven't dared to pull out the ic. please help me with an explanation

[@KhoaTran0720]

Can I use the checkm8 exploit to bypass the setup screen?

[@dmstore4262]

Good job

[@kozo6878]

can you please link where you got the chip

[@stephenafful2314]

Can you replace Qualcomm on item

[@azeemmohamed1520]

plz tell me what soldering iron did u use for wicking pads

[@mansoorpallivathilka]

I think JBC

[@lassinatraore91]

We must replace the circuit where we must remove only and put again

[@ditaarmy]

what brand of blower, bro

[@asunsunsanto3220]

bro i need ask , i got iphone 7 sercing only am flash iphone cant aktif what am work for done iphone , what simcard u use ?

[@solo_mansjournal]

I couldn't activate my iphone 7. It says server is temporarily unavailable. Phone was working fine before resetting.

[@hasanmehdi0110]

Very nice

[@nikolatihomirov8347]

What microscope did you use

[@TTT-V]

so skillful~!!

[@iliyasuhudu1727]

Nice job

[@mrkevin891]

Is iT possible without microscope

[@opolotbenjamin8791]

Am In Uganda I Have the Same Problem How Can I Get it To You to Get It Fixed?

[@mobileworldafrica4213]

Send to me Gh

[@jonathangordon4742]

Can u give a link to where u buyed the chip

[@anjaneyuluvarikupalla7304]

How much it would cost

[@zahangirkhan3457]

I m waiting sir...

[@Daroooo24]

How temp to heat gun?

[@graphicscardtech3167]

Can I do same thing for an iPhone 8 intel version? I’m stuck on set up doesn’t activate

[@RESQREPAIR]

Hey bro. No. Different model, different errors. I have to see the phone and check.

[@haidararafidhi3132]

Merci frère

[@doctorcel]

yo can do this with iphone 8 Qualcom too ?

[@asservicephone]

good 👍👍👍👍

[@anashijjaway141]

Did you change the pb or reball it?

[@andrewg2430]

he replaced it and says it at 12:30

[@ayaanbjjmma4087]

What reason the jumper

[@fabiocme]

Hello friend, what is the reason for the jumper on the bb_pmu ground line?

[@РемонтфотоапаратівСЦАНКОМ]

This is a kind of protection of baseband.

[@BillCarrIpswich]

The GNDs are all needed; they provide a feedback reference to the SMPS (switched mode power supply) lines. The GNDs pads in this location are not very good - the resistance to GND is too high. The SMPS lines then go to a higher voltage, so a 1.0v line can go as high as VDD_Main voltage due to the bad ground.

[@ddysign]

My phone wont boot after bbpmu replacement, is this jumper can solve my problem?

[@mobile_deep_fix_finland]

Very nice!

[@SHABAB_RAJPOOT]

Temperature??

[@amirmobile50]

Good

[@alazagi9]

greetings this works for 1660

[@dsystemwireless283]

whats the name of the hot-air you use? and the tips

[@shariftamu3463]

HI did you managed to get the name plz

[@alazagi9]

También funciona para el 1660

[@herrlip72]

ask your network provider to see if they can give you a Femto Cell

[@AyukFabrice]

Can I keep using my phone without With this fault? I really never use a sim card

[@lahaine8026]

You cant even activate your phone if you have this problem , your phone will be iCloud Locked

[@emanuelrodriguez2177]

what heat station do you use bro?

[@alazagi9]

Se puede para el iPhone 7 a1660

[@teodorospl2993]

How temperature

[@aliajak306]

Perfect👌👌👌

[@afanhaidar7558]

Baseband , IMEI is shown but still it is shown no service what could be the possible problem????

[@Fixmyphonesaket.]

Afan Haidar Zia new pmd

[@afanhaidar7558]

mohit rai what is “pmd”

[@Fixmyphonesaket.]

Baseband power

[@ayoubmaaroufi769]

Hi

[@l4589]

You want sell your stemi 305...?

[@servicehpmedan]

subtitutel indonesia please

[@Kim-eang]

Holle MIs

[@dilipgajjar74]

My mobail ripering oll mobail riperin

[@gbcellular8373]

Tidak untuk d contoh gg jelas

[@dilipgajjar74]

My sop india

[@samettr27]

nice tattoo :)

[@vanhuongta2225]

cảm thấy vô lý

[@waseemabbass4164]

😀😀

[@akramnazeir5505]

👏👏👏👏👏👏👏👏👏👏👏👏👏👏

[@Zeksait]

ю спик ас рашн

[@dilipgajjar74]

Hi

[@dilipgajjar74]

Mi gujarat india

[@dilipgajjar74]

Mi iphone 7