JOG 50 engine assembly tuning 110cc 3KJ by BWSP
HTML-код
- Опубликовано: 28 янв 2020
- Project JOG 110CC...Tuning engine forJOG 50 water cooling with racing ignition, cylinder 54mm, crankshaft long stroke +3mm, modified transmission. www.aliexpress.com/item/33012...
We are able to build any tuning engine or scooter such as JOG50, DIO50, BWS100 and 4 stroke engines like BWS125, GY6-125/150, 5ML, MIO115, YBR125.
★ WEBSITE: tunescoot.site
★ INSTAGRAM: / bwsp_tuning
#bwsptuning #tunescootebwspstudio #yamahajog50 #jog110cc #engine3kj #jogtuning #scootertuning #yamahajog110cc #tuningupgrade #modifiedjog #jog50modification #bigbore #racingperfomance #upgradeengine3kj #upgradejog #scootermodification
Hi , the spare parts from this video on this page tunescoot.site/en/yamaha/jog-90/big-bore-54mm-cylinder-jog50-jog90-3kj-engine-kit-for-racing-125cc
I absolutely love the fact that
After all these years of me building minarelli engines, I’ve never come across someone who obviously does this for a living, only to witness him with a massive deal of confidence in NOT BOTHERING TO PUT SEALANT ON THE CRANK CASES!
I hope who ever you built this for does not watch this video!
Didn’t use any oil/assembly lube to install
The wrist pin bearing, piston or even on the cylinder!
Also nice to see you couldn’t even be bothered to centre the crank after installing.
No torquing the head studs, no squish clearances nothing!
Master mechanic! keep up the good work
i know clearly a mechanic whos there just to make money and not give quality assurance
i mean u dont normally have to squish, but yeah no sealant or lube is a big nono
and to use narakau crankshaft
@@kesperi2 yeahh🤷♂️
Very impressed...you seem to know what your doing.
I like these little engines and they seem very popular within the racing boys.
Well done and nice-n-clean.
Всё супер. Не хватает динамометрического ключа. Закручивать пневмаком придерживая рукой - это круто 😁 спасибо за видос, классное железо 👍
Почему половинки мотора собраны без герметика или прокладки и цилинд тоже стоит без прокладки
You trust those head gaskets sealed the right way. It’s a lot easier if you just use a little bit of Honda bond on the gasket so they stay in place.
Mantap mas bro...
I have a Yamaha slider 2000 model with 3KJ engine . I am willing to modify it like this jog . Thanks for the idea
i like that engine to install diy surfboard my friend..
Did you prelube the piston or cylinder before installation, or did you forget it?
Also could you let me know what cylinder kit this is?
Specs and crankshaft rod length etc..
I have a stroker 88cc kit on mine
What did you use to work the crankcases? A pickaxe? Bruh the boundary layer of fluid on surfaces is important when the fluid is at high speeds..
long belt what length you used? 788 or 820?
Can you recommend an upgrade for my Suzuki street Magic TR50. Flywheel magnets are broken. Might as well think of doing an upgrade with it. Thanks
What ignition please . Is it a pit bike 4t iner rotor ?
Where do you source this kit? I have a 99 yamaha jog I want to do this too. Also any videos of radiator mounted with body panels on?
Hello and how to connect the wiring to the spark ?
Love the videos aloha from hawaii ill be in touch for a motor soon.aloha
What is mainjet did you use
Lut ! Nice musique 🎵
Following this!
Do you have a link for that inner rotor?
Also please link me that handlebar stem pleaseeeeeee
I know its just a cheap one but will come in handy if ever my italkit one dies
Не плохо.👍
Forgot to apply some gasket sealant between the crankcase?
No need just you need to make some force on screw
what is your ignition ? thank you
Che accensione e quella?
Is this same engine on hyosung sd50?
Me gustaría saber si le ase a una adly 2t 100cc
箱体不用密封吗?
where can i buy the complete kit
Ignition coil kit which bike
How many gram the flyball you use?
Donde se puede conseguir ese kit
Quiero un kit de esos para mi 3kj. Donde puedo comprarlo?
Yes le big bore de l'extrême !!
Test run ?
What is the size of the tire
Donde consigo el kit y cuanto cuesta
Magnet AC or DC...?
how u can buy one like this
Where's any seal between the crankcase halves?
Do you leave the crank bearing seal off in the crankcase side of the bearing?
He did but installed the outer seals which are thicker.
how can i get this engine plz
Manin sigue el proyecto quiero ver como acaba
💪💪💪💪
Где можно купить все ето
I want this clindar kit please pro
Where can i buy the crankcase or the engine shell?
1PE40QMB is the Chinese clone of the top mount long case 50cc 2 stroke. The engine in the video is very similar
почему вы не используете скутер или моторный мост? это не вариант. и у вас также есть такие крепления, где вы можете повесить блок двигателя для дальнейшей сборки там. Но хорошие видео. привет из Нидерландов.
что это за цилиндр?
Isn't that engine 3WF, not 3KJ?
Where are can get that kit for my scooter ? please
Mario Martinez if you need kit text me in WhatsApp +8613068844900
for o ring in top head graisse
Dónde puedo conseguir un kit de esos para armar mi proyecto?
Merlit Cepeda tunescoot.site/en/157-yamaha/s-1/engine-3kj
Not hating but your crankshaft should be doing more freely with a load on it and it was stiff but nice build ! If you crack the case again and make she bearings are seated all the way down and the crank is centered and it’ll fix it every time
What I've done what tap the crankshaft ends back and forth to release the side load on the bearings. But yeah I saw that too.
Почему не разговариваешь мне кажется с разговором будет интересно и подписчиков будет больше
Подскажите, какую поршневые поставить на 3wf?
Смотря что по деньгам, если есть 10к то malossi sport, если до 3к то kiyoshi
Thats all? Where 0-100 km/h time?
Tip for poormans over range kit
The piaggio zip torque driver fits minarelli with some minor modification,ends up with even more belt travel than the malossi furia rossa(note the kick starter case needs cutting to fit)
What belt do u use
@@marksantaniello5247 I managed to find one that fits well from a malaguti crosser
Is this will fit with yamaha super jog ZR 50 1993 ?
Yes
@@BWSP-CLUB can it use for Sanex qj50?
Смоттрел и ранее но небыло времени написать.Наличие запчастей это хорошо,но знаний и уверенности в работе нет.Мастер это когда работа кипит,нет лишних движений и ошибок,а сдесь на лицо не опытность мастера.Будем надеятся что опыт и знания прийдут.Ну а так неплохое позновательное видио для начинающих.
link to were i can buy that ignition plz!
jens lorenzen tunescoot.site/en/yamaha/jog-90/sport-rotor-ignition-yamaha-jog50-jog90-tuning-3kj-engine-
Por que no ponen aceite dentro del motor a medida que van armando?
El aceite es lo ultimo que se echa. La prende sin aceite y si marcha bien se lo echa
@@mauro8925 no hermano, al cilindro y las piezas que están en rose se le pone aceite así el primer arranque no lo hace en seco
Привет скажи пожалуйста этл цилиндр от чего и ты его на какой скутер поставил ??
Скорее всего сотая минарелли с доработками
Le vilebrequin ce monte sur aerox minarelli
👌👌👌👌👌👍👍👍👍🌹🌹
no gasket between the block halves?
i was saying the same
Not supposed to use gaskets this is a 2stroke not 4stroke engine slot of inexperienced people commenting on here like you
@@pekelosilveirajr7461 i still put some silicone when putting my engine back together just to be safe
@@WAYZRIDEz yeah I was looking didnt even see silicone on any of the halfs lmao wow
@@pekelosilveirajr7461 you could have been nice and just said nicely that 2-strokes usually don't use gaskets but a sealant instead. No need to be rude and shame people or calling them names. Not everyone knows everything, you know. I'm just saying. Have a nice day.
I want this
Tem algum BR assistindo
Gasket of block!!!😳
why without water coling my man ?
We just haven’t shown it at the video
Y la pasta para sellar motores? Ese motor tiene que tener toma de aire
Roman.Racing text me in whatsapp +8613068844900
TUNESCOOT BWSP STUDIO you hace yo use a sealant ir a join Maker un the carter
He sad; you forgot the gasket/sealant between the two carter halfs. 😳
Do you sell the cylinder? Looking for a 54mm liquid cooler cylinder for my 4dm engine.
How many gram flyball you use ihave 4dm fm crankshaft 788 belt ported pully and tunepipe but stock carb i want it to wheelie and it has a end speed
@@kennethdizon786 idk what pipe you have to give you any advice
@@X7rocks tunepipe bro
@@kennethdizon786 that doesn't tell me anything. I have 6 different "tuned pipes" all for different builds.
@@X7rocks tune pipe malossi stylr
Que precio tiene ese kit
Hi friend, text me in WhatsApp +8613068844900
What is the cost for the kit? Saludos amigo cual es el precio de ese kit?
Hi friend, text me in WhatsApp+8613068844900
cuanto vale el kit para una z tiburón
Quale modèle questo kit ?
donde consigo ese kit
Aliexpress
@@mariocastellanoscervilla7275 como lo pido y cuanto cuesta
Onde posso comprar uma pegá-la dessa ?
ありえく
Where to buy engine case?
WhatsApp +86 13068844900
@@BWSP-CLUB cant find the number on whatsapp?
Так... вы руссские?
عراقي هل يوجد هنا ؟
Whats the bore size sir?
54mm piston size
95cc -.-
109,93061013441CC to be exact 😉
@@pietjepuk6372 oof
top perfomance alu nitro not make 110 cc but 77 or 86cc and for racing pieces no oil no graisse ??? you sur you profetionnel me have 25 years mécanique im never see this
yeah i thought the same. that cylinder is just a 47mm 70cc or 75cc max 80cc, definitely not a 110ccc....
And that exhaust is too smaal for a 110cc it would explode at longer rides...
:(
Ai chiuso il blocco motore senza fare la guarnizione
*Hai
ты заработался где музон
С музоном вечно что то провтыкаешь,и потом по новой...Нужна тишь да гладь..
Картера скрутил без герметика
Так нужно
@@nikita-vc7yv зачем так нужно?
ジョグ50じゃなくて90ですね。
а где герметик?
Він і не потрібен, буде знову розбирати коли та пластмаса з колінвалу в поршневу потрапить і потім приклеїть поршень! Прлвірено на Хонді такт...
Никого не смутило что он не снял боковую нагрузку с коленвала, он еле крутится вообще
Кроме того он даже герметика не положил между половинки когда устанавливал коленвал... :О
Про зрение хочу спросить у вас господа судьи , Вы разве не видите что фильм смонтирован из обрезков, что это далеко не весь процесс сборки, что многое не показано в видео
Zaworu membranowego nie zamontował👌😆
Get a better exhaust and ignition
У меня такая же саксофон был такое дерьмо
Такая же хуйня.Не ехал нихера на ней.Впарил ее каком-то лоху
@@user-mw9oi1gy5b тоже такая же херня, продал соседу! а тот второй год не может понять почему скутер не едет! уже не раз двигатель переберал!😀😀😀
u didnt even sit the crank the right way, this is so not right
jeppe petersen why
And he forgot the gasket between the two engine halfs
@@pietjepuk6372 your not supposed to use gaskets between the engine halfs only rtv silicone have u ever build an scooter engine before probaly not
@@pekelosilveirajr7461 No that is not true, Peugeot and Vespa uses paper gasket.
pekelo silveira jr not only silicone
Go all out just to run an ebay pipe, smh
вы русские?
Українці
Русские ? Чееевоооо?