Micro Drone Toothpick class build 100mm Banggood.com
HTML-код
- Опубликовано: 10 сен 2024
- Toothpick class build, parts list below from Banggood.com
Crazybee F4 Pro V2.0 Mobula7 HD 1-3S Flight Controller
bit.ly/2JGwlv5
AMAXinno 1103 7500KV 1-2S Brushless Motor
bit.ly/2ED3wvl
Caddx Turbo EOS2 4:3 1200TVL 2.1mm 160 Degree 1/3 CMOS Mini FPV
bit.ly/2EBHYPM
Happymodel Mobula7 Part Upgrade Whoop_VTX 5.8G 40CH 25mW~200mW
bit.ly/2VPOAzW
HGLRC M2 2mm Screw Hardware Pack
bit.ly/2McibnA
4 Pairs Gemfan Flash 2540 2.5x4 2.5 Inch 3-Blade Propeller with 1.5mm Mounting Hole
bit.ly/2MbNQ8M
Gaoneng GNB 7.4V 450MAH 80C 2S Lipo Battery XT30 Plug
bit.ly/2wnRmCf
Realacc Trident U.FL IPX IPEX 5.8G 2dBi Omni Directional Linear FPV
bit.ly/2wmg2ea
XT30 1S-3S Plug Parallel Charger Board Banana Plug Input For IMAX B6 Charger
bit.ly/2W83hDl
10X Amass XT30UPB XT30 UPB 2mm Plug Male Female Bullet Connectors
bit.ly/2HEDVnD
2 Pairs Gemfan 65mm 1mm / 1.5mm Hole 2-blade Propeller
bit.ly/2VQCMgF
Pickle Frame
bit.ly/2JJNa8u
Pull off the plastic housing of the plug first, rather easy. Than you can desolder all 3 pins one after the other, grab with tweezer or small pliers, melt solder and pull out the pin. Much easier. If you need the plug afterwards (btw, they are crapcheap), you can reassemble them.
Nice video!
Searching a new board for my Moskito 70....
Just got 2 tyro69's going to use the FC and escs for a 3" build :)
much easier way to remove the motor tabs. Simply push the edge of the tab to create a tiny gap between the edge and the fc then slide a tiny flat blade in the gap and wobble it slightly back and fourth the connector slides right off and you can simply pry the pins off with a small needle nose plies. Takes less than 2 minutes to do all four.
That will save my burnt fingers 👍
@@sp8rk Yes i've done 4 GEPRC12a boards this way and it works great.
+1👍 nice result!
Best vid to date IMHO (",)
hi, may I ask what is the max distance if you use the Y antenna for the vtx?
Hi, I changed it to a dipole as it wasn't a real improvement, and it added a few more grams, the vtx is on 200mw and with the dipole it works just fine, don't bother with the Y antenna (my opinion)
@@sp8rk thank you
cost of this build? Can you compare this one to the new eachine red devil? thanks
About £110 , you could swap out the camera and vtx to an all in one to save a little , but I like the higher quality motors , and 3 cell is not worth it , as they can burn the esc's and destroy the bi props if you prefer using those :/
Would you use the 16x16 iflight stack on this
Yeah, I think that would be ok, a lot of people have had issues with the crazybee boards so great option:) I have stuck a capacitor on my xt 30 plug on my crazybee with no issues :)